Roger Long wrote:
Are you talking about the kind of hose in this picture?

http://home.maine.rr.com/rlma/Bilge.htm#Sump

I can't tell from the photo, Roger, whether it's corrugated or only
reinforced. If it's rated for the application--not only for below
waterline, but for whatever goes through it and the temperature of
it--it's ok. If it's not, I'd replace it.
--
Peggie
----------
Peggie Hall
Specializing in marine sanitation since 1987
Author "Get Rid of Boat Odors - A Guide To Marine Sanitation Systems and
Other Sources of Aggravation and Odor"
http://shop.sailboatowners.com/books...ku=90&cat=1304

Since I started the deviation from the original, and Peggie has raised what
I consider valid points about below-grade stuff...

My applications are for suction or lift only. That is, if it's below
waterline, and attached to a manual bilge pump way above the waterline, the
only time it will be used is to suck up from the bilge. If it's attached to
a submerged bilge pump, the only time it will have water in it is when the
bilge pump is pushing it out, to a vented loop drain.

If those are the uses, are there any caveats? I'm interested in increasing
flow/decreasing resistance by not having that wire-wrap-without-a-slit or
small-shop-vac-suckerhose equivalent usual bilge hose with the cuffs every
foot or so for my discharge. And, my manuals are Whale Gusher 10s, with big
hoses (what's currently there looks about like central vacuum cleaner hose,
but it's not smooth on the inside and quite thinwalled).

And, just to check, I thought that all below-waterline hoses (with static
pressure, of course), for any application, were supposed to be wire
reinforced. Was that urban legend foisted on me by my diesel mech and
surveyor, or true?

Thanks.

L8R

Skip

--
Morgan 461 #2
SV Flying Pig KI4MPC
http://tinyurl.com/384p2 The vessel as Tehamana, as we bought her

"Twenty years from now you will be more disappointed by the things you
didn't do than by the ones you did do. So throw off the bowlines. Sail
away from the safe harbor. Catch the trade winds in your sails. Explore.
Dream. Discover." - Mark Twain
"Peggie Hall" wrote in message
om...
Roger Long wrote:
Are you talking about the kind of hose in this picture?

http://home.maine.rr.com/rlma/Bilge.htm#Sump

I can't tell from the photo, Roger, whether it's corrugated or only
reinforced. If it's rated for the application--not only for below
waterline, but for whatever goes through it and the temperature of
it--it's ok. If it's not, I'd replace it.
--
Peggie
----------
Peggie Hall
Specializing in marine sanitation since 1987
Author "Get Rid of Boat Odors - A Guide To Marine Sanitation Systems and
Other Sources of Aggravation and Odor"
http://shop.sailboatowners.com/books...ku=90&cat=1304

It's reinforced. The inside is like regular hose with only the
slightest irregularity from the outer reinforcing ribs slightly
distorting the plastic as it set. Absent the reinforcing ribs,
it's about as thick as clear plastic hose but appears to be a tougher
material. No wire in it but it would take quite a suction with the
ribs.

I bought this stuff at Hamilton Marine and the box said bilge pump
hose. (They also had the cheap, truly corrugated stuff.) I think
it's OK.

BTW wire can cause it's own problems. When we first tried to start
the engine of our new boat, the cooling system was sucking air. We
spent hours trying to track it down. It finally turned out to be the
connection at the strainer which was very hard to see. Even though
the wire in the hose was stainless, the end had touched the bronze
strainer body and the electrolysis had degraded the rubber.
Fortunately, the seller was paying but that cost him about $250.
Here's a photo:

http://home.maine.rr.com/rlma/Hose.jpg

No choice but to have wire when there is going to be any significant
suction but this is something to watch for when you are cutting the
wire while trimming hoses. Don't let the end of the wire stick out
where it can contact other metal.


--

Roger Long



"Peggie Hall" wrote in message
om...
Roger Long wrote:
Are you talking about the kind of hose in this picture?

http://home.maine.rr.com/rlma/Bilge.htm#Sump

I can't tell from the photo, Roger, whether it's corrugated or only
reinforced. If it's rated for the application--not only for below
waterline, but for whatever goes through it and the temperature of
it--it's ok. If it's not, I'd replace it.
--
Peggie
----------
Peggie Hall
Specializing in marine sanitation since 1987
Author "Get Rid of Boat Odors - A Guide To Marine Sanitation Systems
and Other Sources of Aggravation and Odor"
http://shop.sailboatowners.com/books...ku=90&cat=1304