LinkBack Thread Tools Search this Thread Display Modes
Prev Previous Post   Next Post Next
  #5   Report Post  
posted to rec.boats
external usenet poster
 
First recorded activity by BoatBanter: Feb 2014
Posts: 3,524
Default ??? upgrading shore power to 50A 220V

On 3/18/14, 7:05 AM, Mr. Luddite wrote:
On 3/18/2014 6:26 AM, F*O*A*D wrote:
On 3/17/14, 6:19 PM, KC wrote:
On 3/17/2014 6:01 PM, david@righthere... wrote:
I've been on 30A 120V power at the dock for years and would now like
to upgrade
to 50A 220V, or what they refer to as 50A 250V at the marina office. I
haven't
put a meter on it yet but so far suspect it's closer to 220 than 250.
The socket
on the pedestal is like the one pictured he

http://www.catagle.com/68-153/CWD_Ar...uyersGuide.htm

They say it's 3-pole 4-wire. I'm guessing X and Y are the two hot legs
and W is
the neutral. Between X or Y and W would be 120V+/- and between X and Y
is the
220/250V. Right? How does the ground tie into it though? With only 3
poles do we
run a separate wire from the boat to the pedestal, and if so how do we
tie in?

Also can anyone suggest the cheapest place to get a plug like that? So
far the
best price I've found is $68.18 he

http://www.ktool.net/servlet/the-581...-63CR65/Detail




Thank you for any help!
David


The plug is 10-20 bucks at home depot or lowes, Scottys whatever you
have. It's a dryer plug basically... As to the wiring, I forget but I
have a book I always use when I do the wiring.. It was about 20 bucks at
home depot, I have had it for as long as I have owned a house...



Yikes! It's NOT a dryer plug, basically or otherwise.



Not to knock Scotty but I got a big kick out of his statement, "As to
the wiring, I forget but I have a book I always use when I do the wiring".

I think Scott should limit his wiring to 12 volt devices. Whoops. I
take that back. My oldest grandson recently got his first car and
(like all teenagers) was installing a sound system that included a
massive bass speaker cabinet and a dedicated, 1200 watt amplifier to
drive it. He was wiring the power to the amp with some small gauge
"hook up" wire that he bought. I explained to him that he only had 12
volts +/- available and if the amp was capable of 1200 watts, he could
be drawing close to 100 peak amps at times and his little hookup wire
was going to act like a fuse. Got him some appropriately sized wire.



I'm not a fan of taking unnecessary physical, fire or explosion risks,
so I don't do wiring any more difficult than replacing a switch or a
light fixture. We haven't really had any serious electrical issues here.
The wiring for our generator was handled by the contractor's licensed
electricians.


 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is Off
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Bad shore power [email protected] Cruising 14 June 16th 06 08:09 AM
Shore power plug Roger Long Cruising 18 May 2nd 05 07:57 PM
FS: Shore Power set in NY Bobsprit Marketplace 0 April 16th 04 02:56 AM
Shore Power Parallax Cruising 5 October 15th 03 02:18 PM
Using a generator for AC power in absence of shore power Zeki Gunay Electronics 1 August 7th 03 05:24 PM


All times are GMT +1. The time now is 12:58 AM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 BoatBanter.com.
The comments are property of their posters.
 

About Us

"It's about Boats"

 

Copyright © 2017