On 7/3/2011 4:48 PM, Tim wrote:
Had some old plywood getting soft in the center, and decided to re-do
the floor. when we pulled off the old carpet which was weathered
anyhow, we found out that in the times past someone had repaired the
floor by cutting out a center section and replacing it with standard
plywood. Evidently it had held for quite a while but it's days were
numbered. besides it gave us a chance to inspect the stringers and
other bracing etc.

So, after thinking about the re-floor, we decided to not go with
standard ply because it's not weather resistant, or marine due to the
expense, so we settled on "DRYPLY"

http://www.gp.com/build/product.aspx?pid=4882

A weather resistant plywood which has a lot of characteristics of
marine plywood but is more cost effective. Like $23.00 a 3/4 sheet at
Menards, and in stock too.

Regardless. It ought to last way longer than I'll ever have the boat.

Have you considered not recarpeting and instead putting a non skid
coating on the plywood floor. Carpeting and upholstery in an open
cockpit is a high maintenance proposition'

On Jul 3, 5:00*pm, Jay wrote:
On 7/3/2011 4:48 PM, Tim wrote:









Had some old plywood getting soft in the center, and decided to re-do
the floor. when we pulled off the old carpet which was weathered
anyhow, we found out that in the times past someone had repaired the
floor by cutting out a center section and replacing it with standard
plywood. Evidently it had held for quite a while but it's days were
numbered. besides it gave us a chance to inspect the stringers and
other bracing etc.

So, after thinking about the re-floor, we decided to not go with
standard ply because it's not weather resistant, or marine due to the
expense, so we settled on "DRYPLY"

http://www.gp.com/build/product.aspx?pid=4882

A weather resistant plywood which has a *lot of characteristics of
marine plywood but is more cost effective. Like $23.00 a 3/4 sheet at
Menards, and in stock too.

Regardless. It ought to last way longer than I'll ever have the boat.

Have you considered not recarpeting and instead putting a non skid
coating on the plywood floor. Carpeting and upholstery in an open
cockpit is a high maintenance proposition'

It was considered, but not to the point of stress. It's a trailer boat
that will go to the water then at the end of the day or weekend will
go back to the warehouse, so it's not going to be that big of a deal.
But I'd thought about that. and even lighter colored non-skid surfaces
get hot, so the carpet treatment will do ...

Jay wrote:
On 7/3/2011 4:48 PM, Tim wrote:
Had some old plywood getting soft in the center, and decided to re-do
the floor. when we pulled off the old carpet which was weathered
anyhow, we found out that in the times past someone had repaired the
floor by cutting out a center section and replacing it with standard
plywood. Evidently it had held for quite a while but it's days were
numbered. besides it gave us a chance to inspect the stringers and
other bracing etc.

So, after thinking about the re-floor, we decided to not go with
standard ply because it's not weather resistant, or marine due to the
expense, so we settled on "DRYPLY"

http://www.gp.com/build/product.aspx?pid=4882

A weather resistant plywood which has a lot of characteristics of
marine plywood but is more cost effective. Like $23.00 a 3/4 sheet at
Menards, and in stock too.

Regardless. It ought to last way longer than I'll ever have the boat.

Have you considered not recarpeting and instead putting a non skid
coating on the plywood floor. Carpeting and upholstery in an open
cockpit is a high maintenance proposition'
Good point. There are epoxy coatings that would not only seal the
plywood but would make a great finish coat.

That's pretty good. Have a blessed and great day guys!!!!