Hello,

I am in the throws of deciding on a sailing cruiser to build and
perhaps more importantly which method of construction that I plan to
use prior to ordering plans.

Currently my preferences are either stitch and glue (as I have done
this before) or cedar strip (which looks like an interesting
challenge), but recently I have been looking at the
http://www.glen-l.com/ website where many of their plans require the
craft to be built from Fiberglass planking. So as to consider this
method of construction is anyone aware of suppliers of such planking
in the UK?

Many thanks,
Mark

That is a coincidence but here is another one: we are working on a foam
sandwich version of the VG23.
Already, as designed you could build her that way but I am working on a set
of scantlings.

--
Jacques
http://www.bateau.com


"Mark" wrote in message
om...
Hi Jacques

You are right. I meant planks, but got the subject title wrong.

Interestingly enough, your Vagabond 23 is my primary interest at the
moment, and probably the boat that I will go for. The build will have
to wait until after Christmas to allow the weather to warm a little as
I will be building primarily outside within a small covered area.

My interest was momentarily grabbed by the thought of fiberglass
planks, but if there is no supplier in the UK, I will rule this out on
cost grounds.

Many thanks,
Mark

"Jacques Mertens" wrote in message
.. .
Could that be C-Flex? I don't think they use panels.
For C-Flex, find a company named Seamann. They have an agent in Holland,
don't know about the UK.

--
Jacques
http://www.bateau.com

"Mark" wrote in message
m...
Hello,

I am in the throws of deciding on a sailing cruiser to build and
perhaps more importantly which method of construction that I plan to
use prior to ordering plans.

Currently my preferences are either stitch and glue (as I have done
this before) or cedar strip (which looks like an interesting
challenge), but recently I have been looking at the
http://www.glen-l.com/ website where many of their plans require the
craft to be built from Fiberglass planking. So as to consider this
method of construction is anyone aware of suppliers of such planking
in the UK?

Many thanks,
Mark

Excellent. I've not yet looked into foam sandwich - but it is
something that I would consider.

Time for some more research, I think.

Many thanks,
Mark

"Jacques Mertens" wrote in message . ..
That is a coincidence but here is another one: we are working on a foam
sandwich version of the VG23.
Already, as designed you could build her that way but I am working on a set
of scantlings.

--
Jacques
http://www.bateau.com


"Mark" wrote in message
om...
Hi Jacques

You are right. I meant planks, but got the subject title wrong.

Interestingly enough, your Vagabond 23 is my primary interest at the
moment, and probably the boat that I will go for. The build will have
to wait until after Christmas to allow the weather to warm a little as
I will be building primarily outside within a small covered area.

My interest was momentarily grabbed by the thought of fiberglass
planks, but if there is no supplier in the UK, I will rule this out on
cost grounds.

Many thanks,
Mark

Mark wrote:

Hello,

I am in the throws of deciding on a sailing cruiser to build and
perhaps more importantly which method of construction that I plan to
use prior to ordering plans.

Currently my preferences are either stitch and glue (as I have done
this before) or cedar strip (which looks like an interesting
challenge), but recently I have been looking at the
http://www.glen-l.com/ website where many of their plans require the
craft to be built from Fiberglass planking. So as to consider this
method of construction is anyone aware of suppliers of such planking
in the UK?

Many thanks,
Mark

Usually fabricated in situ, I believe,

As I recall, a frame kit, some c-flex foam tacked on and some
delightful glass-fibre woven material, like fireproof drapes, and
catalyzed polyester resin slopped on can easily become a
'fiberglass panel' boat.

If you useed planks or cut up pieces of plywood instead, you
would have a more traditional wooden boat, no?

Or do you expect to buy sheets of cured fiberglass like plywood,
to be cut to shape or precut shaped panels, and stuck together,
with glue of some sort, like double sided tape or velcro, maybe
nails? Screws are such a bother.

If, after glassing the outside, you glass the inside too, you
would have a foam sandwich construction with floatation core, and
would need to incorperate some connection system to bind the 2
layers of glass together, unless you trust it to adhere strongly
to the foam while sloughing off 10 tons of lumpy seawater while
the loose elephant cargo below makes a break for Freedom and
Africa?

Dream on.

--
Terry K - My email address is MY PROPERTY, and is protected by
copyright legislation. Permission to reproduce it is
specifically denied for mass mailing and unrequested
solicitations. Reproduction or conveyance for any unauthorised
purpose is THEFT and PLAGIARISM. Abuse is Invasion of privacy
and harassment. Abusers may be prosecuted. -This notice footer
released to public domain. Spamspoof salad by spamchock -
SofDevCo

Terry,
Maybe you could research the product the guy is asking about before you
jump in with your useless uninformed (and rather rude) post.

For the original poster:

A yahoo search came up with a few UK locations that mention the C-Flex
fiberglass panels. I didn't search through for specific suppliers but
it appears that they are available. It seems some of the Bruce-Roberts
boats must use this material so contacting one of the places that deals
in their stuff might turn up a source. I have had good results asking
questions at Glen-L so maybe an email to them would help find a source.

Good luck.
Ed



Terry Spragg wrote:

Mark wrote:

Hello,

I am in the throws of deciding on a sailing cruiser to build and
perhaps more importantly which method of construction that I plan to
use prior to ordering plans.

Currently my preferences are either stitch and glue (as I have done
this before) or cedar strip (which looks like an interesting
challenge), but recently I have been looking at the
http://www.glen-l.com/ website where many of their plans require the
craft to be built from Fiberglass planking. So as to consider this
method of construction is anyone aware of suppliers of such planking
in the UK?

Many thanks,
Mark


Usually fabricated in situ, I believe,

As I recall, a frame kit, some c-flex foam tacked on and some
delightful glass-fibre woven material, like fireproof drapes, and
catalyzed polyester resin slopped on can easily become a
'fiberglass panel' boat.

If you useed planks or cut up pieces of plywood instead, you
would have a more traditional wooden boat, no?

Or do you expect to buy sheets of cured fiberglass like plywood,
to be cut to shape or precut shaped panels, and stuck together,
with glue of some sort, like double sided tape or velcro, maybe
nails? Screws are such a bother.

If, after glassing the outside, you glass the inside too, you
would have a foam sandwich construction with floatation core, and
would need to incorperate some connection system to bind the 2
layers of glass together, unless you trust it to adhere strongly
to the foam while sloughing off 10 tons of lumpy seawater while
the loose elephant cargo below makes a break for Freedom and
Africa?

Dream on.

"Terry Spragg" wrote in message
...

If, after glassing the outside, you glass the inside too, you
would have a foam sandwich construction with floatation core, and
would need to incorperate some connection system to bind the 2
layers of glass together, unless you trust it to adhere strongly
to the foam while sloughing off 10 tons of lumpy seawater while
the loose elephant cargo below makes a break for Freedom and
Africa?

Dream on.


? New to me . . . I'm glad I didn't sink during those ocean crossings
because my boat did not have any of those "connections" between the skins.
Maybe we should warn all those yards, builders and designers of foam
sandwich hulls.

and
would need to incorperate some connection system to bind the 2
layers of glass together, unless you trust it to adhere strongly
to the foam while sloughing off 10 tons of lumpy seawater

Interestingly, I've just started working for a company specialising in
attaching resins to many substrates including foam. And I _really_
would trust it to adhere to the foam. I could give you a recipe for
adhesion to of all unlikely substrates, polysyrene, were it not
commerically sensitive.

Al

Terry Spragg wrote in message ...
Mark wrote:

Hello,

I am in the throws of deciding on a sailing cruiser to build and
perhaps more importantly which method of construction that I plan to
use prior to ordering plans.

Currently my preferences are either stitch and glue (as I have done
this before) or cedar strip (which looks like an interesting
challenge), but recently I have been looking at the
http://www.glen-l.com/ website where many of their plans require the
craft to be built from Fiberglass planking. So as to consider this
method of construction is anyone aware of suppliers of such planking
in the UK?

Many thanks,
Mark

Usually fabricated in situ, I believe,

As I recall, a frame kit, some c-flex foam tacked on and some
delightful glass-fibre woven material, like fireproof drapes, and
catalyzed polyester resin slopped on can easily become a
'fiberglass panel' boat.

If you useed planks or cut up pieces of plywood instead, you
would have a more traditional wooden boat, no?

Or do you expect to buy sheets of cured fiberglass like plywood,
to be cut to shape or precut shaped panels, and stuck together,
with glue of some sort, like double sided tape or velcro, maybe
nails? Screws are such a bother.

If, after glassing the outside, you glass the inside too, you
would have a foam sandwich construction with floatation core, and
would need to incorperate some connection system to bind the 2
layers of glass together, unless you trust it to adhere strongly
to the foam while sloughing off 10 tons of lumpy seawater while
the loose elephant cargo below makes a break for Freedom and
Africa?

Dream on.



Sounds to me like you are being sarcastic here, forgive me if I miss.
But if you are mocking this type of "dream" building it is being done
all the time and for some time now. Of course I don't usually carry
elephants around in the bilge, but you never know... maybe pink
ones...
Scotty

Hi Jacques,

Out of interest, do you have a BOM available for the foam sandwiched
version? This would help me do a cost comparison between the ply and
foam versions.

Foam sandwich would be a good way to go for me as I see this boat as
being a project to learn new techniques prior to a bigger build.

Thanks,
Mark

"Jacques Mertens" wrote in message . ..
That is a coincidence but here is another one: we are working on a foam
sandwich version of the VG23.
Already, as designed you could build her that way but I am working on a set
of scantlings.

--
Jacques
http://www.bateau.com

The plans for that version will have a BOM, like all good plans but it's not
ready now, sorry.
We are working on 3 other designs, that job is #4 on the list.

--
Jacques
http://www.bateau.com

"Mark" wrote in message
om...
Hi Jacques,

Out of interest, do you have a BOM available for the foam sandwiched
version? This would help me do a cost comparison between the ply and
foam versions.

Foam sandwich would be a good way to go for me as I see this boat as
being a project to learn new techniques prior to a bigger build.

Thanks,
Mark

"Jacques Mertens" wrote in message
. ..
That is a coincidence but here is another one: we are working on a foam
sandwich version of the VG23.
Already, as designed you could build her that way but I am working on a
set
of scantlings.

--
Jacques
http://www.bateau.com