Drew Dalgleish wrote:
Pretty easy to coble a steambox. I just unscrew the downspout off my
garage and stuff a rag in the end. pop the wood in and prop it up over
the electric kettle. Way easier than making up a laminated gunwale and
faster too.

On Fri, 10 Jul 2009 00:41:31 -0700 (PDT), timmynocky
wrote:

Not much I can add to the previous advice except to say forget the
steaming.
It=92s not worth the hassle of setting up a steam box for a small one
off job, especially when it=92s easier to laminate.
You can stress bend =BD inch around the gentle curves and laminate =BC
inch on the tighter bends.
It=92s always worth trying to source the lumber as close to home as
possible, just in case you need to go back for more....

Mike

http://www.diy-wood-boat.com

On Jul 10, 12:46=A0am, "
wrote:
I am repairing a fiberglass dinghy which has wooden gunwales. =A0The
gunwale wood is rotten and cracked. =A0The inwale and outwale are about
1/2" by 1 1/4" in section, about 11 - 12 feet in length. =A0Where do I
get a replacement hardwood in this size and do I need to steam bend,
or can I just stress bend it using existing bolt holes? =A0What material
is the best for the least?


I made a box because I had the lumber lying around and I use a turkey
fryer. I have an old radiator hose stuck in a piece of plywood which I
secure to the top of the pot of water with an innertube wrapped around a
few times and tied off.. Stick the other end of the hose in the steambox
and make sure you keep the water level up in the pot...

In article ,
says...

Drew Dalgleish wrote:
Pretty easy to coble a steambox. I just unscrew the downspout off my
garage and stuff a rag in the end. pop the wood in and prop it up over
the electric kettle. Way easier than making up a laminated gunwale and
faster too.

On Fri, 10 Jul 2009 00:41:31 -0700 (PDT), timmynocky
wrote:

Not much I can add to the previous advice except to say forget the
steaming.
It=92s not worth the hassle of setting up a steam box for a small one
off job, especially when it=92s easier to laminate.
You can stress bend =BD inch around the gentle curves and laminate =BC
inch on the tighter bends.
It=92s always worth trying to source the lumber as close to home as
possible, just in case you need to go back for more....

Mike

http://www.diy-wood-boat.com

On Jul 10, 12:46=A0am, "
wrote:
I am repairing a fiberglass dinghy which has wooden gunwales. =A0The
gunwale wood is rotten and cracked. =A0The inwale and outwale are about
1/2" by 1 1/4" in section, about 11 - 12 feet in length. =A0Where do I
get a replacement hardwood in this size and do I need to steam bend,
or can I just stress bend it using existing bolt holes? =A0What material
is the best for the least?


I made a box because I had the lumber lying around and I use a turkey
fryer. I have an old radiator hose stuck in a piece of plywood which I
secure to the top of the pot of water with an innertube wrapped around a
few times and tied off.. Stick the other end of the hose in the steambox
and make sure you keep the water level up in the pot...

Yup, I do the same thing exactly, Frier, radiator hose, box...

As to his other question "what kind of wood". I suggest Douglass Fir. Go
to the yard and look at the wider boards for straight grain and cut your
pieces out of that. Fir can be bent over time too. I do 2x6's by
clamping them on and bending them a bit more every day till they fit...
Doug fir is cheap, and it bends nice. You just have to find the straight
grain pieces with no knots in the area you are going to cut.