Home |
Search |
Today's Posts |
|
#1
|
|||
|
|||
Blown head gasket or what...?
1. The oil is not clear but rather milky. The oil level is much higher then
it should be - about 2 inches on a dipstick higher then "full". This is the first oil after reviving the engine (see below) so I'm not sure whether to attribute milkiness to water leftovers or blown gasket. the oil level though is something new. 2. checked the impeller and looks fine, not damaged , no burn marks or anything unusual 3. the water was coming out quite steadily also steam was present 4. there is rust in the intake below carb, there is also a rust streak from s. plug no.4 downwards indicating the water could have been leaking from this plug socket 5. I bought this boat with a seized engine, I soaked it, unseized, ran it several times (never on water), starts and runs OK. When I unseized it I cranked out lot of water from the cylinders (min. 1 liter). What I did was a great success, no mechanic has ever given me any hope. It has stunned everyone. I also unseized another boat of mine (20 ft.) using the same method. Engine runs but the compression is at 60/70 on 2 cyl. so I know I need to hone and replace rings on it, to say the least. I took both as a challenge, bought them and had them running within a month. The idea was to keep both in different locations so I could enjoy some diversity while vacationing. What baffles me is that except for compression test (unexpectedly high) I have all indications of blown head gasket. I have removed risers and manifolds, cleaned them to perfection, installed new gaskets. If it was a riser gasket water concentration would be rather equally spread over the side rather then 1 cylinder Since this is a boat engine I cannot pressurize cooling system easily. I thought of pressurizing the suspected cylinder but couldn't find any inexpensive tool or method of doing it. |
#2
|
|||
|
|||
Blown head gasket or what...?
Check for cracks on the sides of the lifter valley of the block. That is a
common point for cracks when the engine is not winterized and freezes. You can pressure check the system by clamping something inside the hoses. "Proxy" wrote in message .rogers.com... 1. The oil is not clear but rather milky. The oil level is much higher then it should be - about 2 inches on a dipstick higher then "full". This is the first oil after reviving the engine (see below) so I'm not sure whether to attribute milkiness to water leftovers or blown gasket. the oil level though is something new. 2. checked the impeller and looks fine, not damaged , no burn marks or anything unusual 3. the water was coming out quite steadily also steam was present 4. there is rust in the intake below carb, there is also a rust streak from s. plug no.4 downwards indicating the water could have been leaking from this plug socket 5. I bought this boat with a seized engine, I soaked it, unseized, ran it several times (never on water), starts and runs OK. When I unseized it I cranked out lot of water from the cylinders (min. 1 liter). What I did was a great success, no mechanic has ever given me any hope. It has stunned everyone. I also unseized another boat of mine (20 ft.) using the same method. Engine runs but the compression is at 60/70 on 2 cyl. so I know I need to hone and replace rings on it, to say the least. I took both as a challenge, bought them and had them running within a month. The idea was to keep both in different locations so I could enjoy some diversity while vacationing. What baffles me is that except for compression test (unexpectedly high) I have all indications of blown head gasket. I have removed risers and manifolds, cleaned them to perfection, installed new gaskets. If it was a riser gasket water concentration would be rather equally spread over the side rather then 1 cylinder Since this is a boat engine I cannot pressurize cooling system easily. I thought of pressurizing the suspected cylinder but couldn't find any inexpensive tool or method of doing it. |
#3
|
|||
|
|||
Blown head gasket or what...?
To do that I would need to get the intake out, right?
What would be a procedure to pressure check cooling system, can you give some steps, ideas to do it? What are the other ways of pinpointing the problem? "Lawrence James" wrote in message hlink.net... Check for cracks on the sides of the lifter valley of the block. That is a common point for cracks when the engine is not winterized and freezes. You can pressure check the system by clamping something inside the hoses. "Proxy" wrote in message .rogers.com... 1. The oil is not clear but rather milky. The oil level is much higher then it should be - about 2 inches on a dipstick higher then "full". This is the first oil after reviving the engine (see below) so I'm not sure whether to attribute milkiness to water leftovers or blown gasket. the oil level though is something new. 2. checked the impeller and looks fine, not damaged , no burn marks or anything unusual 3. the water was coming out quite steadily also steam was present 4. there is rust in the intake below carb, there is also a rust streak from s. plug no.4 downwards indicating the water could have been leaking from this plug socket 5. I bought this boat with a seized engine, I soaked it, unseized, ran it several times (never on water), starts and runs OK. When I unseized it I cranked out lot of water from the cylinders (min. 1 liter). What I did was a great success, no mechanic has ever given me any hope. It has stunned everyone. I also unseized another boat of mine (20 ft.) using the same method. Engine runs but the compression is at 60/70 on 2 cyl. so I know I need to hone and replace rings on it, to say the least. I took both as a challenge, bought them and had them running within a month. The idea was to keep both in different locations so I could enjoy some diversity while vacationing. What baffles me is that except for compression test (unexpectedly high) I have all indications of blown head gasket. I have removed risers and manifolds, cleaned them to perfection, installed new gaskets. If it was a riser gasket water concentration would be rather equally spread over the side rather then 1 cylinder Since this is a boat engine I cannot pressurize cooling system easily. I thought of pressurizing the suspected cylinder but couldn't find any inexpensive tool or method of doing it. |
#4
|
|||
|
|||
Blown head gasket or what...?
After a long break I'm back with an update. I replaced the head gasket and
(surprise!) put it back together. After some tinkering I created a loop by unhooking intake and water outlet hoses, attached new ones that lead to the bucket with water. Filled the engine with water (mixed with block seal and ran the engine for about 15 min. First impression: after 5 min. I checked the oil and looked quite clear. I observed a water level in the bucket and it stayed the same. No bubbling. In short it seems that head gasket replacement together with intake seals did the trick. I pressure washed the cylinder head and that has revealed some slight rusting around water ports leading to the cylinder bore especially around cyl. no. 4, although not only. Looks like a head gasket was leaking between the block and the head gasket (underneath) although gasket itself was in perfect shape (not tight enough?). That will probably conclude the saga. I'll check it soon where it belongs: in the lake. Thanks everyone for help and words of encouragement. "Lawrence James" wrote in message hlink.net... Check for cracks on the sides of the lifter valley of the block. That is a common point for cracks when the engine is not winterized and freezes. You can pressure check the system by clamping something inside the hoses. "Proxy" wrote in message .rogers.com... 1. The oil is not clear but rather milky. The oil level is much higher then it should be - about 2 inches on a dipstick higher then "full". This is the first oil after reviving the engine (see below) so I'm not sure whether to attribute milkiness to water leftovers or blown gasket. the oil level though is something new. 2. checked the impeller and looks fine, not damaged , no burn marks or anything unusual 3. the water was coming out quite steadily also steam was present 4. there is rust in the intake below carb, there is also a rust streak from s. plug no.4 downwards indicating the water could have been leaking from this plug socket 5. I bought this boat with a seized engine, I soaked it, unseized, ran it several times (never on water), starts and runs OK. When I unseized it I cranked out lot of water from the cylinders (min. 1 liter). What I did was a great success, no mechanic has ever given me any hope. It has stunned everyone. I also unseized another boat of mine (20 ft.) using the same method. Engine runs but the compression is at 60/70 on 2 cyl. so I know I need to hone and replace rings on it, to say the least. I took both as a challenge, bought them and had them running within a month. The idea was to keep both in different locations so I could enjoy some diversity while vacationing. What baffles me is that except for compression test (unexpectedly high) I have all indications of blown head gasket. I have removed risers and manifolds, cleaned them to perfection, installed new gaskets. If it was a riser gasket water concentration would be rather equally spread over the side rather then 1 cylinder Since this is a boat engine I cannot pressurize cooling system easily. I thought of pressurizing the suspected cylinder but couldn't find any inexpensive tool or method of doing it. |
#5
|
|||
|
|||
Blown head gasket or what...?
"Proxy" wrote in message .rogers.com... 1. The oil is not clear but rather milky. The oil level is much higher then it should be - about 2 inches on a dipstick higher then "full". This is the first oil after reviving the engine (see below) so I'm not sure whether to attribute milkiness to water leftovers or blown gasket. the oil level though is something new. The milky color is due to water in the oil. If the oil level is rising on its own that is a clear indication that you are still getting water into the oil. 4. there is rust in the intake below carb, there is also a rust streak from s. plug no.4 downwards indicating the water could have been leaking from this plug socket I would not expect water to leak out of a plug socket. If you have any appreciable amount of water in the cylinder it would hydrolock. 5. I bought this boat with a seized engine, I soaked it, unseized, ran it several times (never on water), starts and runs OK. Okay, that changes my previous recommendations! When I unseized it I cranked out lot of water from the cylinders (min. 1 liter). How long had the engine been sitting with water in it? What baffles me is that except for compression test (unexpectedly high) I thought that the compression was rather high also. Could this be a "high performance" engine, which could have a high compression ratio (and thus require 91 octane gas)??? If you tested the compression right after you got it to turn over for the first time then there is a possibility that you still had some water in the cylinders. This would certainly raise the compression numbers. If you haven't tested it since you actually had it running you might want to do it again. I have all indications of blown head gasket. A head gasket can fail in several ways. The gasket must seal the cylinder pressure. There are also water passages that are under moderate pressure (a few PSI on a boat engine, up to 14 PSI on a closed cooling system). There are also oil passages that are not under pressure. A common failure is to have the pressure from the cylinder rupture the gasket. The rupture can go to the outside, an oil passage, or the water jacket. Such a rupture should show up on a compression test. Other than that, a rupture to the outside might not be noticable. A rupture to the water jacket would cause overheating on a closed cooling system but might be unnoticable on a boat with raw water cooling unless water entered the cylinder when the engine cooled. A rupture to an oil passage would result in excessive amount of "blow by". It is also possible for the water jacket to seal to fail, either to the outside or to an oil passage. To the outside would result in a visible leak, while a ruptuer to the oil passage would cause your crankcase to fill with water. Since the cylinder is still sealed this failure will not show up on a compression test. Usually, this sort of failure is the result of a warped head, perhaps the result of overheating. If the head is warped, just replacing the gasket may not fix the problem. I would recommend removing the heads and examining them. This, of course, requires removal of both the intake and exhaust manifolds, which it sounds like you may have already done once. Generally, once you have the manifolds off getting the heads off isn't too difficult. This will also allow you to examine the cylinders to see if there is any rust issues inside. Rod |
#6
|
|||
|
|||
Blown head gasket or what...?
OK, changed the oil today, pumped out 9 liters ! of sludge, some of it so
thick that I couldn't believe my eyes. As indicated I have not had the boat in the water yet (no time plus a big "?" with regard to the engine). Oil filter contained almost no oil but water. I ran the engine last year on the hose for about 20 min altogether. That was after putting new oil in the engine (first change after getting it to run). Considering short time that I had it running on the hose it seems like I have a major leak. Since compression is quite high (140-160) I wonder whether it is something else other then head gasket (cracked block?). Water seems to accumulate in crackcase although as I said looks like also in cyl. # 4. I ran the engine today for about 30 sec. (dry, no water). Seems to be working, This a regular 305 8cyl. 5L OMC engine, nothing special about it. I guess there is no way to avoid heads removal. I bought Block Seal (K&W product) after I read some really good comments about it (many swar by it). I planned to connect 2 exhaust water hoses (that are normally hooked to manifolds) together and connect them with water inlet hose (unhook from the outdrive - bell housing) thereby creating a loop. I planned to fill it with water mixed with Block Seal and run it for 5 min. That should help seal small cracks (wonder how small or big mine is). If no improvement I would remove heads. In theory my plan looks OK but God knows.... Considering what I've accomplished so far without taking the engine apart I'm still optimistic although prospects are quite tough. What do you think should I do? What is the most likely fault/damage here? "Rod McInnis" wrote in message ... "Proxy" wrote in message .rogers.com... 1. The oil is not clear but rather milky. The oil level is much higher then it should be - about 2 inches on a dipstick higher then "full". This is the first oil after reviving the engine (see below) so I'm not sure whether to attribute milkiness to water leftovers or blown gasket. the oil level though is something new. The milky color is due to water in the oil. If the oil level is rising on its own that is a clear indication that you are still getting water into the oil. 4. there is rust in the intake below carb, there is also a rust streak from s. plug no.4 downwards indicating the water could have been leaking from this plug socket I would not expect water to leak out of a plug socket. If you have any appreciable amount of water in the cylinder it would hydrolock. 5. I bought this boat with a seized engine, I soaked it, unseized, ran it several times (never on water), starts and runs OK. Okay, that changes my previous recommendations! When I unseized it I cranked out lot of water from the cylinders (min. 1 liter). How long had the engine been sitting with water in it? What baffles me is that except for compression test (unexpectedly high) I thought that the compression was rather high also. Could this be a "high performance" engine, which could have a high compression ratio (and thus require 91 octane gas)??? If you tested the compression right after you got it to turn over for the first time then there is a possibility that you still had some water in the cylinders. This would certainly raise the compression numbers. If you haven't tested it since you actually had it running you might want to do it again. I have all indications of blown head gasket. A head gasket can fail in several ways. The gasket must seal the cylinder pressure. There are also water passages that are under moderate pressure (a few PSI on a boat engine, up to 14 PSI on a closed cooling system). There are also oil passages that are not under pressure. A common failure is to have the pressure from the cylinder rupture the gasket. The rupture can go to the outside, an oil passage, or the water jacket. Such a rupture should show up on a compression test. Other than that, a rupture to the outside might not be noticable. A rupture to the water jacket would cause overheating on a closed cooling system but might be unnoticable on a boat with raw water cooling unless water entered the cylinder when the engine cooled. A rupture to an oil passage would result in excessive amount of "blow by". It is also possible for the water jacket to seal to fail, either to the outside or to an oil passage. To the outside would result in a visible leak, while a ruptuer to the oil passage would cause your crankcase to fill with water. Since the cylinder is still sealed this failure will not show up on a compression test. Usually, this sort of failure is the result of a warped head, perhaps the result of overheating. If the head is warped, just replacing the gasket may not fix the problem. I would recommend removing the heads and examining them. This, of course, requires removal of both the intake and exhaust manifolds, which it sounds like you may have already done once. Generally, once you have the manifolds off getting the heads off isn't too difficult. This will also allow you to examine the cylinders to see if there is any rust issues inside. Rod |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Head Gasket on 50 HP 93 Evinrude | General | |||
head gasket failure, salt water in cylinders, question? | General | |||
Nannidiesel 2.50 - 14 HP : used 88 hrs then cylinder head gasket failure : continued | General | |||
Jabsco Head - help! | General | |||
Nannidiesel 2.50 - 14HP : used 88 hrs then cylinder head gasket failure ! | General |