Home |
Search |
Today's Posts |
#5
|
|||
|
|||
To All :
Thanks for your quick responses. The boat is a cabin cruiser with a swim platform on the transom ... water did not splash over the transom and into the fuel injection system. Water contamination was found on the dipstick during a pre-launch checkout. The mechanic is telling me that water may have been sucked in through the exhaust port - either from coming off plane too quickly (never happens) or may have splashed up into the exhaust manifold area from being offloaded from the ramp into the water. He said some manufacturers don't position the engine or stringers right, so a boat may be more prone to taking on water even from just being put into the water off the trailer. I've found some info from the BoatUS consumer site that discusses water ingestion problems .. seems it's a design flaw that required changes in the exhaust manifold to prevent back suction of water into the exhaust valve area when it is still partially open during the intake stroke. I'm intending to pursue this issue with the manufacturer (LARSON) and Volvo. Thanks to Dr.Smithers for the link to Volvo. If I find the dealer and/or Volvo giving me a run-around for what looks like a design deficiency, I may consider pursuing legal class-action, as I'm probably not the only one who has been hit with this problem. For anyone out of warranty, they'd be stuck with the repair bill for something that is due to poor design. With the co$t of a boat, I don't expect to have to continue to pay co$tly repair$ for something the manufacturer should have designed correctly in the first place. We found the water in oil condition during a routine pre-launch check ... I've had many years of experience rebuilding automotive engines and readily recognized the symptoms of water contamination. Further, I just don't buy the "this is normal and/or expected" types of answers .. it IS a design flaw. Boats are sold with an implied "fitness of purpose" to be used on the water. To tell me that I shouldn't abruptly slow down or even worry about boat ramp loading areas as a problem is unacceptable. In my "day job" I'm an computer engineer .. if I were to tell someone they could only use their computers under strict parameters, people would rightly tell me I'm being ridiculous. Boats SHOULD be designed to function under the types of conditions expected for on-water use - to have an inherent problem that causes water ingestion under too easy of conditions is NOT proper design for what the boat was intended to do. Thanks to all for the feedback ! Ralph JamesgangNC wrote: Yea, but if it was running the water would pretty much be expelled before a noticable amount could get past the rings into the oil. Having said that it is always advisable to back down slowly to avoid having the wake overwash your tail. As far as cam overlap I have about as much overlap with a crane cam in a sb as possible with a wet exhaust and I still don't have water in the oil. The question is how much water??? No water should be in the oil. Any more than a little is really bad because it goes to the bottom of the oil pan and that where your oil pump pick up is. And a very slight amount is usually vaporized and vented. How did you find the water? While draining the oil? "Eisboch" wrote in message ... Dr. Dr. Smithers wrote: Is the mechanic saying that you came off plane and the water came over the transom and was ingested by the fuel injection system? If so, you would have noticed if you had ever had that problem, and even if the water flooded the deck, I can not imagine it leaking into the fuel injection system. If it will, you need to correct that leak, because you will always have water in a boat. . I would not accept that answer from the dealer. You can contact Volvo Penta directly at: http://www.volvo.com/volvopenta/glob...nited%20States "Ralph Modica" wrote in message ... Hello : I have a 2003 Larson Cabrio 254 Cabin Crusier w/73 hours on the 5.7 Volvo Penta I/O. Have recently discovered water in the engine oil. The dealer's mechanic is telling me this is "Normal" and may occur if the boat ingests water while coming down off-plane too rapidly or even if water is splashed too high while putting the boat in the water at a launch ramp. Seems this is TOO easy an "explanation" for what I think is a defective engine gasket. IF this IS something common, I'm amazed more people have not complained to the manufacturer's about designing their boats better to avoid water ingestion. I've also heard water ingestion is a common problem on Volvo 8-cylinder I/O engines. There is apparently a problem with valve timing being off - this allows the intake stroke to pull vacuum while an exhaust valve is still open, thus sucking water into the cylinders. Has anyone here heard of this or have further details ? Thanks in advance ! Ralph I don't know how the Volvo setup is designed, but I suspect the mechanic is saying that the water slap on the transom pushed up into the exhaust risers and then into a cylinder or two through the exhaust valves. It ain't supposed to happen, but it can. Eisboch |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
rec.boats.paddle sea kayaking FAQ | General | |||
rec.boats.paddle sea kayaking FAQ | General | |||
rec.boats.paddle sea kayaking FAQ | General | |||
Evinrude FICHT beats out Yamaha in JD Powers survey | General | |||
Engine News from Genmar | General |