Mr. Luddite wrote:
On 10/11/2018 8:12 PM, wrote:
On Thu, 11 Oct 2018 16:42:41 -0400, "Mr. Luddite"
wrote:

On 10/11/2018 3:40 PM, wrote:
On Thu, 11 Oct 2018 14:11:23 -0400, John H.
wrote:


http://tinyurl.com/y7dezaq3

"The left is revving up attacks on capitalism just as workers on the
bottom rungs are beginning to
benefit from the booming U.S. economy. According to last week's jobs
report, unemployment has been
pushed back to its lowest level since 1969. Wages in blue-collar
industries, such as construction
and maintenance, are rising faster than for white-collar workers. Pay
for people without a college
education jumped almost 6 percent since last year -- triple the overall wage gain."

Gosh, I thought wage growth was stagnant.

There was an article in USA Today yesterday talking about .how wages
are going up across the board and some jobs are really taking off

BTW your link took me to Harbor Fright generators.

About that, why is my 5.5 KW Briggs 11 hp and theirs is 8?
They must have stronger horses in China



With no losses considered:

8 hp = 5.96Kw
11 hp = 8.2Kw

I completely forgot about a small generator I bought from a neighbor
last year. It was brand new, still in the box and she
decided to have a whole house generator installed instead. She
only wanted $200 for it but after looking it up I decided I'd be
ripping her off, so I gave her $300. It's rated at 4,750 peak watts
and 3800 watts continuous. Engine is 6.3 hp.

I put it together last spring and fired it up. Ran fine, was not
overly noisy (for a conventional type generator). It has electric
start which is nice and will run on gas or propane, although propane
is at a reduced output capacity. I ran it out of gas and stored it away
and, until just now, had forgotten I had it. It's a "Wren" that she got
from Home Depot:

https://tinyurl.com/ybef4hty

I keep hearing about the reduced output capacity on propane but I
don't see it. I will say fuel consumption is where the difference of
energy density shows up. At full load the gasoline consumption is
around 0.5 GPH and propane is more like 0.8 GPH although the gasoline
is easier to measure accurately. I am just going on a gauge on a 150
gallon tank and that is not very precise.
After a similar discussion on the real boat group I tested my
generator using my convection oven as the load.
This is 5402.7w running a 5500w generator on propane
http://gfretwell.com/Propaneproject/Onpropane.jpg
When I plugged in two 100w lights, it tripped the breaker before I
could take pictures.



I think any generator can temporarily exceed their rated capacity but
they may not last long if done on a regular basis. Windings and other
components will get hot and go "poof". It's not often that generators
are running all the time at full capacity and if they are, you probably
need a bigger generator. :-)

I mentioned before that the little Honda I have is rated for 2,000 watts
surge and 1600 watts continuous or 13.3 amps. It ran my large microwave
with a measured amperage draw of over 16 amps for a short time but as
soon as I realized how much current was being drawn I shut the microwave
off. I wouldn't do that on a regular basis. The circuit breaker on the
generator never tripped.

I've been looking around for a larger portable generator but I want one
with 4 poles instead of the typical 2 poles. 4 poles will allow the
engine to run at 1800 RPM to produce it's rated output at 60Hz instead
of the typical 3600 RPM in a 2 pole generator. 3600 RPM is the main
reason they are so noisy.





My Yamaha 2000 runs my Samsung camper microwave fine. Never ran it for a
long time, mostly heat water for coffee.

On Fri, 12 Oct 2018 05:04:47 -0000 (UTC), Bill
wrote:

Mr. Luddite wrote:
On 10/11/2018 8:12 PM, wrote:
On Thu, 11 Oct 2018 16:42:41 -0400, "Mr. Luddite"
wrote:

On 10/11/2018 3:40 PM, wrote:
On Thu, 11 Oct 2018 14:11:23 -0400, John H.
wrote:


http://tinyurl.com/y7dezaq3

"The left is revving up attacks on capitalism just as workers on the
bottom rungs are beginning to
benefit from the booming U.S. economy. According to last week's jobs
report, unemployment has been
pushed back to its lowest level since 1969. Wages in blue-collar
industries, such as construction
and maintenance, are rising faster than for white-collar workers. Pay
for people without a college
education jumped almost 6 percent since last year -- triple the overall wage gain."

Gosh, I thought wage growth was stagnant.

There was an article in USA Today yesterday talking about .how wages
are going up across the board and some jobs are really taking off

BTW your link took me to Harbor Fright generators.

About that, why is my 5.5 KW Briggs 11 hp and theirs is 8?
They must have stronger horses in China



With no losses considered:

8 hp = 5.96Kw
11 hp = 8.2Kw

I completely forgot about a small generator I bought from a neighbor
last year. It was brand new, still in the box and she
decided to have a whole house generator installed instead. She
only wanted $200 for it but after looking it up I decided I'd be
ripping her off, so I gave her $300. It's rated at 4,750 peak watts
and 3800 watts continuous. Engine is 6.3 hp.

I put it together last spring and fired it up. Ran fine, was not
overly noisy (for a conventional type generator). It has electric
start which is nice and will run on gas or propane, although propane
is at a reduced output capacity. I ran it out of gas and stored it away
and, until just now, had forgotten I had it. It's a "Wren" that she got
from Home Depot:

https://tinyurl.com/ybef4hty

I keep hearing about the reduced output capacity on propane but I
don't see it. I will say fuel consumption is where the difference of
energy density shows up. At full load the gasoline consumption is
around 0.5 GPH and propane is more like 0.8 GPH although the gasoline
is easier to measure accurately. I am just going on a gauge on a 150
gallon tank and that is not very precise.
After a similar discussion on the real boat group I tested my
generator using my convection oven as the load.
This is 5402.7w running a 5500w generator on propane
http://gfretwell.com/Propaneproject/Onpropane.jpg
When I plugged in two 100w lights, it tripped the breaker before I
could take pictures.



I think any generator can temporarily exceed their rated capacity but
they may not last long if done on a regular basis. Windings and other
components will get hot and go "poof". It's not often that generators
are running all the time at full capacity and if they are, you probably
need a bigger generator. :-)

I mentioned before that the little Honda I have is rated for 2,000 watts
surge and 1600 watts continuous or 13.3 amps. It ran my large microwave
with a measured amperage draw of over 16 amps for a short time but as
soon as I realized how much current was being drawn I shut the microwave
off. I wouldn't do that on a regular basis. The circuit breaker on the
generator never tripped.

I've been looking around for a larger portable generator but I want one
with 4 poles instead of the typical 2 poles. 4 poles will allow the
engine to run at 1800 RPM to produce it's rated output at 60Hz instead
of the typical 3600 RPM in a 2 pole generator. 3600 RPM is the main
reason they are so noisy.





My Yamaha 2000 runs my Samsung camper microwave fine. Never ran it for a
long time, mostly heat water for coffee.

I was able to run the microwave but with the low voltage, it did not
sound all that great so we didn't do it much. I made coffee before I
turned on the pool pump and little things like that got us by. With a
little discipline we could even use a stove burner but I had the gas
burner so I used that. We were pioneer folk, heating water on the
propane burner to wash dishes but it really wasn't bad.
Having the pool blue really made the lack of A/C a non issue. In fact
cleaning up the pool was one of the first things I did. Getting all of
that crap out of the pool as soon as I could saved it. I didn't even
have it greening up on is.
My neighbor's pools were all pea soup in a day or two. I had the pool
and spa blue the whole time even tho all I could run on the spa was
the low speed circulation.
My wife was commenting this evening about how fast the whole
neighborhood got to work on recovering.
If you are sitting around without A/C you might as well go outside and
get some **** done. Once I got the basic stuff working here I hopped
in my cart and went around the neighborhood checking on my neighbors.
I ran into other guys doing the same thing.
Nothing like a good storm to meet your neighbors. Fortunately there
really was not that much really bad stuff here and a lot of people had
bailed anyway.
I did find a free generator for my next door neighbor Luis (from our
board president) that just needed a carburetor job and he had it
running that evening. They had a brand new one they scored before the
storm.

On Fri, 12 Oct 2018 05:04:47 -0000 (UTC), Bill wrote:

Mr. Luddite wrote:
On 10/11/2018 8:12 PM, wrote:
On Thu, 11 Oct 2018 16:42:41 -0400, "Mr. Luddite"
wrote:

On 10/11/2018 3:40 PM, wrote:
On Thu, 11 Oct 2018 14:11:23 -0400, John H.
wrote:


http://tinyurl.com/y7dezaq3

"The left is revving up attacks on capitalism just as workers on the
bottom rungs are beginning to
benefit from the booming U.S. economy. According to last week's jobs
report, unemployment has been
pushed back to its lowest level since 1969. Wages in blue-collar
industries, such as construction
and maintenance, are rising faster than for white-collar workers. Pay
for people without a college
education jumped almost 6 percent since last year -- triple the overall wage gain."

Gosh, I thought wage growth was stagnant.

There was an article in USA Today yesterday talking about .how wages
are going up across the board and some jobs are really taking off

BTW your link took me to Harbor Fright generators.

About that, why is my 5.5 KW Briggs 11 hp and theirs is 8?
They must have stronger horses in China



With no losses considered:

8 hp = 5.96Kw
11 hp = 8.2Kw

I completely forgot about a small generator I bought from a neighbor
last year. It was brand new, still in the box and she
decided to have a whole house generator installed instead. She
only wanted $200 for it but after looking it up I decided I'd be
ripping her off, so I gave her $300. It's rated at 4,750 peak watts
and 3800 watts continuous. Engine is 6.3 hp.

I put it together last spring and fired it up. Ran fine, was not
overly noisy (for a conventional type generator). It has electric
start which is nice and will run on gas or propane, although propane
is at a reduced output capacity. I ran it out of gas and stored it away
and, until just now, had forgotten I had it. It's a "Wren" that she got
from Home Depot:

https://tinyurl.com/ybef4hty

I keep hearing about the reduced output capacity on propane but I
don't see it. I will say fuel consumption is where the difference of
energy density shows up. At full load the gasoline consumption is
around 0.5 GPH and propane is more like 0.8 GPH although the gasoline
is easier to measure accurately. I am just going on a gauge on a 150
gallon tank and that is not very precise.
After a similar discussion on the real boat group I tested my
generator using my convection oven as the load.
This is 5402.7w running a 5500w generator on propane
http://gfretwell.com/Propaneproject/Onpropane.jpg
When I plugged in two 100w lights, it tripped the breaker before I
could take pictures.



I think any generator can temporarily exceed their rated capacity but
they may not last long if done on a regular basis. Windings and other
components will get hot and go "poof". It's not often that generators
are running all the time at full capacity and if they are, you probably
need a bigger generator. :-)

I mentioned before that the little Honda I have is rated for 2,000 watts
surge and 1600 watts continuous or 13.3 amps. It ran my large microwave
with a measured amperage draw of over 16 amps for a short time but as
soon as I realized how much current was being drawn I shut the microwave
off. I wouldn't do that on a regular basis. The circuit breaker on the
generator never tripped.

I've been looking around for a larger portable generator but I want one
with 4 poles instead of the typical 2 poles. 4 poles will allow the
engine to run at 1800 RPM to produce it's rated output at 60Hz instead
of the typical 3600 RPM in a 2 pole generator. 3600 RPM is the main
reason they are so noisy.





My Yamaha 2000 runs my Samsung camper microwave fine. Never ran it for a
long time, mostly heat water for coffee.

Even the bigger microwaves are only about 1200 watts. Shouldn't be a problem for the 2000 watter.

On 10/12/2018 5:49 AM, John H. wrote:
On Fri, 12 Oct 2018 05:04:47 -0000 (UTC), Bill wrote:

Mr. Luddite wrote:
On 10/11/2018 8:12 PM, wrote:
On Thu, 11 Oct 2018 16:42:41 -0400, "Mr. Luddite"
wrote:

On 10/11/2018 3:40 PM, wrote:
On Thu, 11 Oct 2018 14:11:23 -0400, John H.
wrote:


http://tinyurl.com/y7dezaq3

"The left is revving up attacks on capitalism just as workers on the
bottom rungs are beginning to
benefit from the booming U.S. economy. According to last week's jobs
report, unemployment has been
pushed back to its lowest level since 1969. Wages in blue-collar
industries, such as construction
and maintenance, are rising faster than for white-collar workers. Pay
for people without a college
education jumped almost 6 percent since last year -- triple the overall wage gain."

Gosh, I thought wage growth was stagnant.

There was an article in USA Today yesterday talking about .how wages
are going up across the board and some jobs are really taking off

BTW your link took me to Harbor Fright generators.

About that, why is my 5.5 KW Briggs 11 hp and theirs is 8?
They must have stronger horses in China



With no losses considered:

8 hp = 5.96Kw
11 hp = 8.2Kw

I completely forgot about a small generator I bought from a neighbor
last year. It was brand new, still in the box and she
decided to have a whole house generator installed instead. She
only wanted $200 for it but after looking it up I decided I'd be
ripping her off, so I gave her $300. It's rated at 4,750 peak watts
and 3800 watts continuous. Engine is 6.3 hp.

I put it together last spring and fired it up. Ran fine, was not
overly noisy (for a conventional type generator). It has electric
start which is nice and will run on gas or propane, although propane
is at a reduced output capacity. I ran it out of gas and stored it away
and, until just now, had forgotten I had it. It's a "Wren" that she got
from Home Depot:

https://tinyurl.com/ybef4hty

I keep hearing about the reduced output capacity on propane but I
don't see it. I will say fuel consumption is where the difference of
energy density shows up. At full load the gasoline consumption is
around 0.5 GPH and propane is more like 0.8 GPH although the gasoline
is easier to measure accurately. I am just going on a gauge on a 150
gallon tank and that is not very precise.
After a similar discussion on the real boat group I tested my
generator using my convection oven as the load.
This is 5402.7w running a 5500w generator on propane
http://gfretwell.com/Propaneproject/Onpropane.jpg
When I plugged in two 100w lights, it tripped the breaker before I
could take pictures.



I think any generator can temporarily exceed their rated capacity but
they may not last long if done on a regular basis. Windings and other
components will get hot and go "poof". It's not often that generators
are running all the time at full capacity and if they are, you probably
need a bigger generator. :-)

I mentioned before that the little Honda I have is rated for 2,000 watts
surge and 1600 watts continuous or 13.3 amps. It ran my large microwave
with a measured amperage draw of over 16 amps for a short time but as
soon as I realized how much current was being drawn I shut the microwave
off. I wouldn't do that on a regular basis. The circuit breaker on the
generator never tripped.

I've been looking around for a larger portable generator but I want one
with 4 poles instead of the typical 2 poles. 4 poles will allow the
engine to run at 1800 RPM to produce it's rated output at 60Hz instead
of the typical 3600 RPM in a 2 pole generator. 3600 RPM is the main
reason they are so noisy.





My Yamaha 2000 runs my Samsung camper microwave fine. Never ran it for a
long time, mostly heat water for coffee.



Even the bigger microwaves are only about 1200 watts. Shouldn't be a problem for the 2000 watter.


John, the 1200 watt rating is the microwave output power, not the power
required to produce it. My 1200 watt microwave draws just over 16 amps
to run. 120v x 16 amps = 1920 watts which is over the continuous
output rating of the Honda (1600 watts). It means the Honda has to run
near or at it's "surge" capacity continuously in order to power the 1200
watt microwave.

Mr. Luddite wrote:
On 10/12/2018 5:49 AM, John H. wrote:
On Fri, 12 Oct 2018 05:04:47 -0000 (UTC), Bill wrote:

Mr. Luddite wrote:
On 10/11/2018 8:12 PM, wrote:
On Thu, 11 Oct 2018 16:42:41 -0400, "Mr. Luddite"
wrote:

On 10/11/2018 3:40 PM, wrote:
On Thu, 11 Oct 2018 14:11:23 -0400, John H.
wrote:


http://tinyurl.com/y7dezaq3

"The left is revving up attacks on capitalism just as workers on the
bottom rungs are beginning to
benefit from the booming U.S. economy. According to last week's jobs
report, unemployment has been
pushed back to its lowest level since 1969. Wages in blue-collar
industries, such as construction
and maintenance, are rising faster than for white-collar workers. Pay
for people without a college
education jumped almost 6 percent since last year -- triple the overall wage gain."

Gosh, I thought wage growth was stagnant.

There was an article in USA Today yesterday talking about .how wages
are going up across the board and some jobs are really taking off

BTW your link took me to Harbor Fright generators.

About that, why is my 5.5 KW Briggs 11 hp and theirs is 8?
They must have stronger horses in China



With no losses considered:

8 hp = 5.96Kw
11 hp = 8.2Kw

I completely forgot about a small generator I bought from a neighbor
last year. It was brand new, still in the box and she
decided to have a whole house generator installed instead. She
only wanted $200 for it but after looking it up I decided I'd be
ripping her off, so I gave her $300. It's rated at 4,750 peak watts
and 3800 watts continuous. Engine is 6.3 hp.

I put it together last spring and fired it up. Ran fine, was not
overly noisy (for a conventional type generator). It has electric
start which is nice and will run on gas or propane, although propane
is at a reduced output capacity. I ran it out of gas and stored it away
and, until just now, had forgotten I had it. It's a "Wren" that she got
from Home Depot:

https://tinyurl.com/ybef4hty

I keep hearing about the reduced output capacity on propane but I
don't see it. I will say fuel consumption is where the difference of
energy density shows up. At full load the gasoline consumption is
around 0.5 GPH and propane is more like 0.8 GPH although the gasoline
is easier to measure accurately. I am just going on a gauge on a 150
gallon tank and that is not very precise.
After a similar discussion on the real boat group I tested my
generator using my convection oven as the load.
This is 5402.7w running a 5500w generator on propane
http://gfretwell.com/Propaneproject/Onpropane.jpg
When I plugged in two 100w lights, it tripped the breaker before I
could take pictures.



I think any generator can temporarily exceed their rated capacity but
they may not last long if done on a regular basis. Windings and other
components will get hot and go "poof". It's not often that generators
are running all the time at full capacity and if they are, you probably
need a bigger generator. :-)

I mentioned before that the little Honda I have is rated for 2,000 watts
surge and 1600 watts continuous or 13.3 amps. It ran my large microwave
with a measured amperage draw of over 16 amps for a short time but as
soon as I realized how much current was being drawn I shut the microwave
off. I wouldn't do that on a regular basis. The circuit breaker on the
generator never tripped.

I've been looking around for a larger portable generator but I want one
with 4 poles instead of the typical 2 poles. 4 poles will allow the
engine to run at 1800 RPM to produce it's rated output at 60Hz instead
of the typical 3600 RPM in a 2 pole generator. 3600 RPM is the main
reason they are so noisy.





My Yamaha 2000 runs my Samsung camper microwave fine. Never ran it for a
long time, mostly heat water for coffee.



Even the bigger microwaves are only about 1200 watts. Shouldn't be a
problem for the 2000 watter.


John, the 1200 watt rating is the microwave output power, not the power
required to produce it. My 1200 watt microwave draws just over 16 amps
to run. 120v x 16 amps = 1920 watts which is over the continuous
output rating of the Honda (1600 watts). It means the Honda has to run
near or at it's "surge" capacity continuously in order to power the 1200
watt microwave.





I would figure most microwave units should be about 14 amps max. They are
designed to run on 15 amp circuits.

On Fri, 12 Oct 2018 14:37:24 -0000 (UTC), Bill
wrote:

Mr. Luddite wrote:
On 10/12/2018 5:49 AM, John H. wrote:
On Fri, 12 Oct 2018 05:04:47 -0000 (UTC), Bill wrote:

Mr. Luddite wrote:
On 10/11/2018 8:12 PM, wrote:
On Thu, 11 Oct 2018 16:42:41 -0400, "Mr. Luddite"
wrote:

On 10/11/2018 3:40 PM, wrote:
On Thu, 11 Oct 2018 14:11:23 -0400, John H.
wrote:


http://tinyurl.com/y7dezaq3

"The left is revving up attacks on capitalism just as workers on the
bottom rungs are beginning to
benefit from the booming U.S. economy. According to last week's jobs
report, unemployment has been
pushed back to its lowest level since 1969. Wages in blue-collar
industries, such as construction
and maintenance, are rising faster than for white-collar workers. Pay
for people without a college
education jumped almost 6 percent since last year -- triple the overall wage gain."

Gosh, I thought wage growth was stagnant.

There was an article in USA Today yesterday talking about .how wages
are going up across the board and some jobs are really taking off

BTW your link took me to Harbor Fright generators.

About that, why is my 5.5 KW Briggs 11 hp and theirs is 8?
They must have stronger horses in China



With no losses considered:

8 hp = 5.96Kw
11 hp = 8.2Kw

I completely forgot about a small generator I bought from a neighbor
last year. It was brand new, still in the box and she
decided to have a whole house generator installed instead. She
only wanted $200 for it but after looking it up I decided I'd be
ripping her off, so I gave her $300. It's rated at 4,750 peak watts
and 3800 watts continuous. Engine is 6.3 hp.

I put it together last spring and fired it up. Ran fine, was not
overly noisy (for a conventional type generator). It has electric
start which is nice and will run on gas or propane, although propane
is at a reduced output capacity. I ran it out of gas and stored it away
and, until just now, had forgotten I had it. It's a "Wren" that she got
from Home Depot:

https://tinyurl.com/ybef4hty

I keep hearing about the reduced output capacity on propane but I
don't see it. I will say fuel consumption is where the difference of
energy density shows up. At full load the gasoline consumption is
around 0.5 GPH and propane is more like 0.8 GPH although the gasoline
is easier to measure accurately. I am just going on a gauge on a 150
gallon tank and that is not very precise.
After a similar discussion on the real boat group I tested my
generator using my convection oven as the load.
This is 5402.7w running a 5500w generator on propane
http://gfretwell.com/Propaneproject/Onpropane.jpg
When I plugged in two 100w lights, it tripped the breaker before I
could take pictures.



I think any generator can temporarily exceed their rated capacity but
they may not last long if done on a regular basis. Windings and other
components will get hot and go "poof". It's not often that generators
are running all the time at full capacity and if they are, you probably
need a bigger generator. :-)

I mentioned before that the little Honda I have is rated for 2,000 watts
surge and 1600 watts continuous or 13.3 amps. It ran my large microwave
with a measured amperage draw of over 16 amps for a short time but as
soon as I realized how much current was being drawn I shut the microwave
off. I wouldn't do that on a regular basis. The circuit breaker on the
generator never tripped.

I've been looking around for a larger portable generator but I want one
with 4 poles instead of the typical 2 poles. 4 poles will allow the
engine to run at 1800 RPM to produce it's rated output at 60Hz instead
of the typical 3600 RPM in a 2 pole generator. 3600 RPM is the main
reason they are so noisy.





My Yamaha 2000 runs my Samsung camper microwave fine. Never ran it for a
long time, mostly heat water for coffee.



Even the bigger microwaves are only about 1200 watts. Shouldn't be a
problem for the 2000 watter.


John, the 1200 watt rating is the microwave output power, not the power
required to produce it. My 1200 watt microwave draws just over 16 amps
to run. 120v x 16 amps = 1920 watts which is over the continuous
output rating of the Honda (1600 watts). It means the Honda has to run
near or at it's "surge" capacity continuously in order to power the 1200
watt microwave.





I would figure most microwave units should be about 14 amps max. They are
designed to run on 15 amp circuits.

Max on a 15a circuit is 12a (1440w). There are a few exceptions but
none if it has a plug on it.

On 10/12/2018 2:04 PM, wrote:
On Fri, 12 Oct 2018 14:37:24 -0000 (UTC), Bill
wrote:

Mr. Luddite wrote:
On 10/12/2018 5:49 AM, John H. wrote:
On Fri, 12 Oct 2018 05:04:47 -0000 (UTC), Bill wrote:

Mr. Luddite wrote:
On 10/11/2018 8:12 PM, wrote:
On Thu, 11 Oct 2018 16:42:41 -0400, "Mr. Luddite"
wrote:

On 10/11/2018 3:40 PM, wrote:
On Thu, 11 Oct 2018 14:11:23 -0400, John H.
wrote:


http://tinyurl.com/y7dezaq3

"The left is revving up attacks on capitalism just as workers on the
bottom rungs are beginning to
benefit from the booming U.S. economy. According to last week's jobs
report, unemployment has been
pushed back to its lowest level since 1969. Wages in blue-collar
industries, such as construction
and maintenance, are rising faster than for white-collar workers. Pay
for people without a college
education jumped almost 6 percent since last year -- triple the overall wage gain."

Gosh, I thought wage growth was stagnant.

There was an article in USA Today yesterday talking about .how wages
are going up across the board and some jobs are really taking off

BTW your link took me to Harbor Fright generators.

About that, why is my 5.5 KW Briggs 11 hp and theirs is 8?
They must have stronger horses in China



With no losses considered:

8 hp = 5.96Kw
11 hp = 8.2Kw

I completely forgot about a small generator I bought from a neighbor
last year. It was brand new, still in the box and she
decided to have a whole house generator installed instead. She
only wanted $200 for it but after looking it up I decided I'd be
ripping her off, so I gave her $300. It's rated at 4,750 peak watts
and 3800 watts continuous. Engine is 6.3 hp.

I put it together last spring and fired it up. Ran fine, was not
overly noisy (for a conventional type generator). It has electric
start which is nice and will run on gas or propane, although propane
is at a reduced output capacity. I ran it out of gas and stored it away
and, until just now, had forgotten I had it. It's a "Wren" that she got
from Home Depot:

https://tinyurl.com/ybef4hty

I keep hearing about the reduced output capacity on propane but I
don't see it. I will say fuel consumption is where the difference of
energy density shows up. At full load the gasoline consumption is
around 0.5 GPH and propane is more like 0.8 GPH although the gasoline
is easier to measure accurately. I am just going on a gauge on a 150
gallon tank and that is not very precise.
After a similar discussion on the real boat group I tested my
generator using my convection oven as the load.
This is 5402.7w running a 5500w generator on propane
http://gfretwell.com/Propaneproject/Onpropane.jpg
When I plugged in two 100w lights, it tripped the breaker before I
could take pictures.



I think any generator can temporarily exceed their rated capacity but
they may not last long if done on a regular basis. Windings and other
components will get hot and go "poof". It's not often that generators
are running all the time at full capacity and if they are, you probably
need a bigger generator. :-)

I mentioned before that the little Honda I have is rated for 2,000 watts
surge and 1600 watts continuous or 13.3 amps. It ran my large microwave
with a measured amperage draw of over 16 amps for a short time but as
soon as I realized how much current was being drawn I shut the microwave
off. I wouldn't do that on a regular basis. The circuit breaker on the
generator never tripped.

I've been looking around for a larger portable generator but I want one
with 4 poles instead of the typical 2 poles. 4 poles will allow the
engine to run at 1800 RPM to produce it's rated output at 60Hz instead
of the typical 3600 RPM in a 2 pole generator. 3600 RPM is the main
reason they are so noisy.





My Yamaha 2000 runs my Samsung camper microwave fine. Never ran it for a
long time, mostly heat water for coffee.



Even the bigger microwaves are only about 1200 watts. Shouldn't be a
problem for the 2000 watter.


John, the 1200 watt rating is the microwave output power, not the power
required to produce it. My 1200 watt microwave draws just over 16 amps
to run. 120v x 16 amps = 1920 watts which is over the continuous
output rating of the Honda (1600 watts). It means the Honda has to run
near or at it's "surge" capacity continuously in order to power the 1200
watt microwave.





I would figure most microwave units should be about 14 amps max. They are
designed to run on 15 amp circuits.

Max on a 15a circuit is 12a (1440w). There are a few exceptions but
none if it has a plug on it.



I am not a code expert but why then, when you go to Lowe's or Home Depot
are the wall receptacles marked as "15 amp" or "20 amp"?

I've always wired a 20 amp outlet with 12 ga romex and 15 amp with 14
ga. and use the appropriate breaker in the service panel. More often
than not I skip the 15 amp altogether and just wire for 20 amp.

Have the codes changed?

On Fri, 12 Oct 2018 14:56:36 -0400, "Mr. Luddite"
wrote:

On 10/12/2018 2:04 PM, wrote:
On Fri, 12 Oct 2018 14:37:24 -0000 (UTC), Bill
wrote:

Mr. Luddite wrote:
On 10/12/2018 5:49 AM, John H. wrote:
On Fri, 12 Oct 2018 05:04:47 -0000 (UTC), Bill wrote:

Mr. Luddite wrote:
On 10/11/2018 8:12 PM, wrote:
On Thu, 11 Oct 2018 16:42:41 -0400, "Mr. Luddite"
wrote:

On 10/11/2018 3:40 PM, wrote:
On Thu, 11 Oct 2018 14:11:23 -0400, John H.
wrote:


http://tinyurl.com/y7dezaq3

"The left is revving up attacks on capitalism just as workers on the
bottom rungs are beginning to
benefit from the booming U.S. economy. According to last week's jobs
report, unemployment has been
pushed back to its lowest level since 1969. Wages in blue-collar
industries, such as construction
and maintenance, are rising faster than for white-collar workers. Pay
for people without a college
education jumped almost 6 percent since last year -- triple the overall wage gain."

Gosh, I thought wage growth was stagnant.

There was an article in USA Today yesterday talking about .how wages
are going up across the board and some jobs are really taking off

BTW your link took me to Harbor Fright generators.

About that, why is my 5.5 KW Briggs 11 hp and theirs is 8?
They must have stronger horses in China



With no losses considered:

8 hp = 5.96Kw
11 hp = 8.2Kw

I completely forgot about a small generator I bought from a neighbor
last year. It was brand new, still in the box and she
decided to have a whole house generator installed instead. She
only wanted $200 for it but after looking it up I decided I'd be
ripping her off, so I gave her $300. It's rated at 4,750 peak watts
and 3800 watts continuous. Engine is 6.3 hp.

I put it together last spring and fired it up. Ran fine, was not
overly noisy (for a conventional type generator). It has electric
start which is nice and will run on gas or propane, although propane
is at a reduced output capacity. I ran it out of gas and stored it away
and, until just now, had forgotten I had it. It's a "Wren" that she got
from Home Depot:

https://tinyurl.com/ybef4hty

I keep hearing about the reduced output capacity on propane but I
don't see it. I will say fuel consumption is where the difference of
energy density shows up. At full load the gasoline consumption is
around 0.5 GPH and propane is more like 0.8 GPH although the gasoline
is easier to measure accurately. I am just going on a gauge on a 150
gallon tank and that is not very precise.
After a similar discussion on the real boat group I tested my
generator using my convection oven as the load.
This is 5402.7w running a 5500w generator on propane
http://gfretwell.com/Propaneproject/Onpropane.jpg
When I plugged in two 100w lights, it tripped the breaker before I
could take pictures.



I think any generator can temporarily exceed their rated capacity but
they may not last long if done on a regular basis. Windings and other
components will get hot and go "poof". It's not often that generators
are running all the time at full capacity and if they are, you probably
need a bigger generator. :-)

I mentioned before that the little Honda I have is rated for 2,000 watts
surge and 1600 watts continuous or 13.3 amps. It ran my large microwave
with a measured amperage draw of over 16 amps for a short time but as
soon as I realized how much current was being drawn I shut the microwave
off. I wouldn't do that on a regular basis. The circuit breaker on the
generator never tripped.

I've been looking around for a larger portable generator but I want one
with 4 poles instead of the typical 2 poles. 4 poles will allow the
engine to run at 1800 RPM to produce it's rated output at 60Hz instead
of the typical 3600 RPM in a 2 pole generator. 3600 RPM is the main
reason they are so noisy.





My Yamaha 2000 runs my Samsung camper microwave fine. Never ran it for a
long time, mostly heat water for coffee.



Even the bigger microwaves are only about 1200 watts. Shouldn't be a
problem for the 2000 watter.


John, the 1200 watt rating is the microwave output power, not the power
required to produce it. My 1200 watt microwave draws just over 16 amps
to run. 120v x 16 amps = 1920 watts which is over the continuous
output rating of the Honda (1600 watts). It means the Honda has to run
near or at it's "surge" capacity continuously in order to power the 1200
watt microwave.





I would figure most microwave units should be about 14 amps max. They are
designed to run on 15 amp circuits.

Max on a 15a circuit is 12a (1440w). There are a few exceptions but
none if it has a plug on it.



I am not a code expert but why then, when you go to Lowe's or Home Depot
are the wall receptacles marked as "15 amp" or "20 amp"?

I've always wired a 20 amp outlet with 12 ga romex and 15 amp with 14
ga. and use the appropriate breaker in the service panel. More often
than not I skip the 15 amp altogether and just wire for 20 amp.

Have the codes changed?

No.
A 20a has to be on 12ga but you can put a 15 on either as long as
there is more than one receptacle on the circuit. A duplex is 2.
There is no limit to how many you put on a circuit tho in residential.

Commercial has a 180va per duplex (90 per receptacle) rating for each
based on full circuit ampacity (not the 80%). I think Canada extends
that to residential.

The thinking in residential is receptacles are placed for convenience,
not actual load and most will not be used most of the time so you can
have all you want on a circuit. The NEC does not address "design".
Basically they are trying to avoid the need of extension cords and
cords running across doorways so the general rule is you are always
within 6' of a receptacle without crossing an opening. That includes
any wall space 24" or wider.
In the kitchen, on the counter top you are 2' from a receptacle.
This takes about 6-7 pages of fine print and pictures in the NEC to
describe. Damn lawyers ;-)
210.52 is one of the more confusing articles.

On Fri, 12 Oct 2018 08:05:14 -0400, "Mr. Luddite" wrote:

On 10/12/2018 5:49 AM, John H. wrote:
On Fri, 12 Oct 2018 05:04:47 -0000 (UTC), Bill wrote:

Mr. Luddite wrote:
On 10/11/2018 8:12 PM, wrote:
On Thu, 11 Oct 2018 16:42:41 -0400, "Mr. Luddite"
wrote:

On 10/11/2018 3:40 PM, wrote:
On Thu, 11 Oct 2018 14:11:23 -0400, John H.
wrote:


http://tinyurl.com/y7dezaq3

"The left is revving up attacks on capitalism just as workers on the
bottom rungs are beginning to
benefit from the booming U.S. economy. According to last week's jobs
report, unemployment has been
pushed back to its lowest level since 1969. Wages in blue-collar
industries, such as construction
and maintenance, are rising faster than for white-collar workers. Pay
for people without a college
education jumped almost 6 percent since last year -- triple the overall wage gain."

Gosh, I thought wage growth was stagnant.

There was an article in USA Today yesterday talking about .how wages
are going up across the board and some jobs are really taking off

BTW your link took me to Harbor Fright generators.

About that, why is my 5.5 KW Briggs 11 hp and theirs is 8?
They must have stronger horses in China



With no losses considered:

8 hp = 5.96Kw
11 hp = 8.2Kw

I completely forgot about a small generator I bought from a neighbor
last year. It was brand new, still in the box and she
decided to have a whole house generator installed instead. She
only wanted $200 for it but after looking it up I decided I'd be
ripping her off, so I gave her $300. It's rated at 4,750 peak watts
and 3800 watts continuous. Engine is 6.3 hp.

I put it together last spring and fired it up. Ran fine, was not
overly noisy (for a conventional type generator). It has electric
start which is nice and will run on gas or propane, although propane
is at a reduced output capacity. I ran it out of gas and stored it away
and, until just now, had forgotten I had it. It's a "Wren" that she got
from Home Depot:

https://tinyurl.com/ybef4hty

I keep hearing about the reduced output capacity on propane but I
don't see it. I will say fuel consumption is where the difference of
energy density shows up. At full load the gasoline consumption is
around 0.5 GPH and propane is more like 0.8 GPH although the gasoline
is easier to measure accurately. I am just going on a gauge on a 150
gallon tank and that is not very precise.
After a similar discussion on the real boat group I tested my
generator using my convection oven as the load.
This is 5402.7w running a 5500w generator on propane
http://gfretwell.com/Propaneproject/Onpropane.jpg
When I plugged in two 100w lights, it tripped the breaker before I
could take pictures.



I think any generator can temporarily exceed their rated capacity but
they may not last long if done on a regular basis. Windings and other
components will get hot and go "poof". It's not often that generators
are running all the time at full capacity and if they are, you probably
need a bigger generator. :-)

I mentioned before that the little Honda I have is rated for 2,000 watts
surge and 1600 watts continuous or 13.3 amps. It ran my large microwave
with a measured amperage draw of over 16 amps for a short time but as
soon as I realized how much current was being drawn I shut the microwave
off. I wouldn't do that on a regular basis. The circuit breaker on the
generator never tripped.

I've been looking around for a larger portable generator but I want one
with 4 poles instead of the typical 2 poles. 4 poles will allow the
engine to run at 1800 RPM to produce it's rated output at 60Hz instead
of the typical 3600 RPM in a 2 pole generator. 3600 RPM is the main
reason they are so noisy.





My Yamaha 2000 runs my Samsung camper microwave fine. Never ran it for a
long time, mostly heat water for coffee.



Even the bigger microwaves are only about 1200 watts. Shouldn't be a problem for the 2000 watter.


John, the 1200 watt rating is the microwave output power, not the power
required to produce it. My 1200 watt microwave draws just over 16 amps
to run. 120v x 16 amps = 1920 watts which is over the continuous
output rating of the Honda (1600 watts). It means the Honda has to run
near or at it's "surge" capacity continuously in order to power the 1200
watt microwave.



You are correct. Thank you!

On 10/12/2018 1:04 AM, Bill wrote:
Mr. Luddite wrote:
On 10/11/2018 8:12 PM, wrote:
On Thu, 11 Oct 2018 16:42:41 -0400, "Mr. Luddite"
wrote:

On 10/11/2018 3:40 PM, wrote:
On Thu, 11 Oct 2018 14:11:23 -0400, John H.
wrote:


http://tinyurl.com/y7dezaq3

"The left is revving up attacks on capitalism just as workers on the
bottom rungs are beginning to
benefit from the booming U.S. economy. According to last week's jobs
report, unemployment has been
pushed back to its lowest level since 1969. Wages in blue-collar
industries, such as construction
and maintenance, are rising faster than for white-collar workers. Pay
for people without a college
education jumped almost 6 percent since last year -- triple the overall wage gain."

Gosh, I thought wage growth was stagnant.

There was an article in USA Today yesterday talking about .how wages
are going up across the board and some jobs are really taking off

BTW your link took me to Harbor Fright generators.

About that, why is my 5.5 KW Briggs 11 hp and theirs is 8?
They must have stronger horses in China



With no losses considered:

8 hp = 5.96Kw
11 hp = 8.2Kw

I completely forgot about a small generator I bought from a neighbor
last year. It was brand new, still in the box and she
decided to have a whole house generator installed instead. She
only wanted $200 for it but after looking it up I decided I'd be
ripping her off, so I gave her $300. It's rated at 4,750 peak watts
and 3800 watts continuous. Engine is 6.3 hp.

I put it together last spring and fired it up. Ran fine, was not
overly noisy (for a conventional type generator). It has electric
start which is nice and will run on gas or propane, although propane
is at a reduced output capacity. I ran it out of gas and stored it away
and, until just now, had forgotten I had it. It's a "Wren" that she got
from Home Depot:

https://tinyurl.com/ybef4hty

I keep hearing about the reduced output capacity on propane but I
don't see it. I will say fuel consumption is where the difference of
energy density shows up. At full load the gasoline consumption is
around 0.5 GPH and propane is more like 0.8 GPH although the gasoline
is easier to measure accurately. I am just going on a gauge on a 150
gallon tank and that is not very precise.
After a similar discussion on the real boat group I tested my
generator using my convection oven as the load.
This is 5402.7w running a 5500w generator on propane
http://gfretwell.com/Propaneproject/Onpropane.jpg
When I plugged in two 100w lights, it tripped the breaker before I
could take pictures.



I think any generator can temporarily exceed their rated capacity but
they may not last long if done on a regular basis. Windings and other
components will get hot and go "poof". It's not often that generators
are running all the time at full capacity and if they are, you probably
need a bigger generator. :-)

I mentioned before that the little Honda I have is rated for 2,000 watts
surge and 1600 watts continuous or 13.3 amps. It ran my large microwave
with a measured amperage draw of over 16 amps for a short time but as
soon as I realized how much current was being drawn I shut the microwave
off. I wouldn't do that on a regular basis. The circuit breaker on the
generator never tripped.

I've been looking around for a larger portable generator but I want one
with 4 poles instead of the typical 2 poles. 4 poles will allow the
engine to run at 1800 RPM to produce it's rated output at 60Hz instead
of the typical 3600 RPM in a 2 pole generator. 3600 RPM is the main
reason they are so noisy.





My Yamaha 2000 runs my Samsung camper microwave fine. Never ran it for a
long time, mostly heat water for coffee.


The Honda 2000 runs the smaller, counter-top microwave fine as well, but
it's only rated at 750 watts versus the 1200 watts that the over stove,
built in microwave is rated at. I purposely shopped for the lowest
wattage small microwave I could find and 750 watts seemed to be the
smallest. It still draws about 11 amps when running, so it needs 1320
watts of power to produce 750 watts of microwave power. 1320 watts is
within the Honda's rated continuous output of 1600 watts.

That's the thing. Can't confuse output power rating of the microwave
with the input required to produce it. The large microwave was drawing
slightly over 16 amps to produce 1200 watts of microwave power. That's
at least 1920 watts. The Honda is only rated for 1600 watts continuous
output and 2000 watts "surge". So to run the large microwave the Honda
was running near or at it's surge rating continuously. Not good.