On 5/22/2010 1:49 PM, YukonBound wrote:


"hk" wrote in message
...
On 5/22/10 9:37 AM, moose wrote:
On 5/22/2010 9:17 AM, *e#c wrote:
On May 21, 5:07 pm, wrote:
i dont think mine are...but just curious about the warning signs...

Are they used in Salt, or Fresh Water?

Cracks on the outside ( you'll see rust stains ) . Cracks on the
inside are hard to immediately see. Over heating is a sure sign. Using
clear tubing while idling...do you see any bubbles passing through? I
just rebuilt my 40 year old Risers over the winter. Soaking them in
Pickling Vinegar worked great to clean them out. After that, I scored
out the cracks very slightly with the Dremel, and put a nice coat of
JB Weld over top, followed by a coat of Tremclad white.The finishing
touch was to paint the Exhaust Stubs with High Heat Enamel. They do
look nice now.

You've had your warning. The next one won't be so subtle. Spell
hydrolock, or is it hydralock?

So, you went right from chipping paint on old navy ships to sucking
used lower unit oil out of outdrives?


His lips are of Olympic capabilities after years & years of training.

See. This is what earned you a seat on the short bus.

On May 22, 9:37*am, moose wrote:
On 5/22/2010 9:17 AM, *e#c wrote:

On May 21, 5:07 pm, *wrote:
i dont think mine are...but just curious about the warning signs...

Are they used in Salt, or Fresh Water?

Cracks on the outside ( you'll see rust stains ) . Cracks on the
inside are hard to immediately see. Over heating is a sure sign. Using
clear tubing while idling...do you see any bubbles passing through? I
just rebuilt my 40 year old Risers over the winter. Soaking them in
Pickling Vinegar worked great to clean them out. After that, I scored
out the cracks very slightly with the Dremel, and put a nice coat of
JB Weld over top, followed by a coat of Tremclad white.The finishing
touch was to paint the Exhaust Stubs with High Heat Enamel. They do
look nice now.

You've had your warning. The next one won't be so subtle. Spell
hydrolock, or is it hydralock?

Looks as though you've had a " brainlock ". Get with the topic, or
keep your pie-hole shut. You've added nothing to this thread but pure
****.

On 5/22/2010 4:17 PM, *e#c wrote:
On May 22, 9:37 am, wrote:
On 5/22/2010 9:17 AM, *e#c wrote:

On May 21, 5:07 pm, wrote:
i dont think mine are...but just curious about the warning signs...

Are they used in Salt, or Fresh Water?

Cracks on the outside ( you'll see rust stains ) . Cracks on the
inside are hard to immediately see. Over heating is a sure sign. Using
clear tubing while idling...do you see any bubbles passing through? I
just rebuilt my 40 year old Risers over the winter. Soaking them in
Pickling Vinegar worked great to clean them out. After that, I scored
out the cracks very slightly with the Dremel, and put a nice coat of
JB Weld over top, followed by a coat of Tremclad white.The finishing
touch was to paint the Exhaust Stubs with High Heat Enamel. They do
look nice now.

You've had your warning. The next one won't be so subtle. Spell
hydrolock, or is it hydralock?

Looks as though you've had a " brainlock ". Get with the topic, or
keep your pie-hole shut. You've added nothing to this thread but pure
****.

Since you are such a dimwit, i won't bother explaining the process to
you. BTW it was spot on topic.

On May 22, 4:44*pm, moose wrote:
On 5/22/2010 4:17 PM, *e#c wrote:



On May 22, 9:37 am, *wrote:
On 5/22/2010 9:17 AM, *e#c wrote:

On May 21, 5:07 pm, * *wrote:
i dont think mine are...but just curious about the warning signs...

Are they used in Salt, or Fresh Water?

Cracks on the outside ( you'll see rust stains ) . Cracks on the
inside are hard to immediately see. Over heating is a sure sign. Using
clear tubing while idling...do you see any bubbles passing through? I
just rebuilt my 40 year old Risers over the winter. Soaking them in
Pickling Vinegar worked great to clean them out. After that, I scored
out the cracks very slightly with the Dremel, and put a nice coat of
JB Weld over top, followed by a coat of Tremclad white.The finishing
touch was to paint the Exhaust Stubs with High Heat Enamel. They do
look nice now.

You've had your warning. The next one won't be so subtle. Spell
hydrolock, or is it hydralock?

Looks as though you've had a " brainlock ". Get with the topic, or
keep your pie-hole shut. You've added nothing to this thread but pure
****.

Since you are such a dimwit, i won't bother explaining the process to
you. BTW it was spot on topic.

Then you should have been a real man about it, and explained yourself.
But perhaps you cant, and just slink off like the coward you are.

On Sat, 22 May 2010 06:17:36 -0700 (PDT), "*e#c"
wrote:

On May 21, 5:07*pm, bpuharic wrote:
i dont think mine are...but just curious about the warning signs...

Are they used in Salt, or Fresh Water?

definitely salt water...


Cracks on the outside ( you'll see rust stains )

ah...very interesting...haven't seen anything like that. when i
changed the exhaust lines i checked the inside...they looked pretty
good but will watch

On May 22, 8:21*pm, bpuharic wrote:
On Sat, 22 May 2010 06:17:36 -0700 (PDT), "*e#c"

wrote:
On May 21, 5:07*pm, bpuharic wrote:
i dont think mine are...but just curious about the warning signs...

Are they used in Salt, or Fresh Water?

definitely salt water...



Cracks on the outside ( you'll see rust stains )

ah...very interesting...haven't seen anything like that. when i
changed the exhaust lines i checked the inside...they looked pretty
good but will watch

You didnt mention what the engine/drive setup is. I have no idea what
make of riser you're talking about. I was referring to mine, an
ancient OMC setup. In my manual, a test for air is to replace two of
the riser water output lines to check for air bubbles moving through
the lines when the engine is idling.
I imagine you're using something far newer than mine. But, as you can
see...Moosy just has to show its true colors, and pollute the thread,
without explanation of what its talking about. I'm no Mechanic, just a
driveway hero.I fix my own Boat, and it runs fine.

I would think that Risers used in Salt Water should be cleaned about
every 100 hours of steady use. If stationary, maybe every 150 hours.
Thats a guess, but Moosy will no doubt pollute us again with his idle
threats, and impish bull****.

On May 22, 9:17*am, "*e#c" wrote:
On May 21, 5:07*pm, bpuharic wrote:

i dont think mine are...but just curious about the warning signs...

Are they used in Salt, or Fresh Water?

Cracks on the outside ( you'll see rust stains ) . Cracks on the
inside are hard to immediately see. Over heating is a sure sign. Using
clear tubing while idling...do you see any bubbles passing through? I
just rebuilt my 40 year old Risers over the winter. Soaking them in
Pickling Vinegar worked great to clean them out. After that, I scored
out the cracks very slightly with the Dremel, and put a nice coat of
JB Weld over top, followed by a coat of Tremclad white.The finishing
touch was to paint the Exhaust Stubs with High Heat Enamel. They do
look nice now.

You need to buy some new risers. JBWeld is not going to stay in
cracks, the expansion coefficient is to different. You're just asking
for problems.

On Mon, 24 May 2010 05:08:20 -0700 (PDT), jamesgangnc
wrote:

You need to buy some new risers. JBWeld is not going to stay in
cracks, the expansion coefficient is to different. You're just asking
for problems.

Excellent advice.

On May 24, 8:08*am, jamesgangnc wrote:
On May 22, 9:17*am, "*e#c" wrote:

On May 21, 5:07*pm, bpuharic wrote:

i dont think mine are...but just curious about the warning signs...

Are they used in Salt, or Fresh Water?

Cracks on the outside ( you'll see rust stains ) . Cracks on the
inside are hard to immediately see. Over heating is a sure sign. Using
clear tubing while idling...do you see any bubbles passing through? I
just rebuilt my 40 year old Risers over the winter. Soaking them in
Pickling Vinegar worked great to clean them out. After that, I scored
out the cracks very slightly with the Dremel, and put a nice coat of
JB Weld over top, followed by a coat of Tremclad white.The finishing
touch was to paint the Exhaust Stubs with High Heat Enamel. They do
look nice now.

You need to buy some new risers. *JBWeld is not going to stay in
cracks, the expansion coefficient is to different. *You're just asking
for problems.

Thats funny, because the last application lasted TWO YEARS without
water penetrating through it. And the only reason I removed that
application, was to boil them out. I've had that statement said to me
before.
It has also lasted over two years on the block cracks the engine has .
I check them constantly. Are you getting your information first hand,
as in your experience...or just heresay?
If its first hand, you didnt clean the repaired area well enough.