Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
posted to rec.boats.cruising
external usenet poster
 
First recorded activity by BoatBanter: Jul 2006
Posts: 674
Default check valve

Here's another pic of the discharge. Not sure why I said it before, but the discharge is on the starboard side, not the port side. The port side is engine discharge. I must be dyslexic today.

http://picasaweb.google.com/SailNOW....20431152743042
  #2   Report Post  
posted to rec.boats.cruising
external usenet poster
 
First recorded activity by BoatBanter: Jun 2007
Posts: 760
Default check valve


"Jonathan Ganz" wrote in message
...
Here's another pic of the discharge. Not sure why I said it before, but
the discharge is on the starboard side, not the port side. The port side
is engine discharge. I must be dyslexic today.



Druglexic more like it. And not just today, everyday.

--
Gregory Hall


  #3   Report Post  
posted to rec.boats.cruising
external usenet poster
 
First recorded activity by BoatBanter: Jun 2007
Posts: 739
Default check valve

No need for a vented loop on those but it's probably worth putting in just
to reduce the back flow and amount of water in the bilge.

While you're at it perhaps we should revisit my current thinking on bilge
pumps ad currently done on "Strider".

The Rule, et. a., pumps often have a short life sitting in the bilge water.
Most of the water they pump is in very small amounts. The hose sized for
the pump to save your boat is large enough to cause a lot of backflow and
water in the bilge with a transom discharge. The answer to both problems is
two pumps. The first, in your current location, would be a small pump with
a 1/2 or 5/8 hose. This will easily deal with condensation, stuffing box
drips, etc. It will also make less noise and draw less current. The
second pump would be located high enough above the bilge that it will always
be dry, it can have a simple float switch because, if it is ever needed, it
will probably go on and stay on until the battery runs down. This pump
would be the largest appropriate for the hose diameter.

You could put a Tee a couple feet downstream of the vented loop and run the
small pump into that. If only the big pump was running, some water would
divert back into the bilge but, mose likely, the litte pump would already be
working against a leak that was simply faster than it could keep up with.

The ideal thing would be a second line for the primary (small) pump. I
would run this out the counter bottom just ahead of the transom.

--
Roger Long



  #4   Report Post  
posted to rec.boats.cruising
external usenet poster
 
First recorded activity by BoatBanter: Jul 2006
Posts: 674
Default check valve

In article ,
Roger Long wrote:
No need for a vented loop on those but it's probably worth putting in just
to reduce the back flow and amount of water in the bilge.

While you're at it perhaps we should revisit my current thinking on bilge
pumps ad currently done on "Strider".

The Rule, et. a., pumps often have a short life sitting in the bilge water.
Most of the water they pump is in very small amounts. The hose sized for
the pump to save your boat is large enough to cause a lot of backflow and
water in the bilge with a transom discharge. The answer to both problems is
two pumps. The first, in your current location, would be a small pump with
a 1/2 or 5/8 hose. This will easily deal with condensation, stuffing box
drips, etc. It will also make less noise and draw less current. The
second pump would be located high enough above the bilge that it will always
be dry, it can have a simple float switch because, if it is ever needed, it
will probably go on and stay on until the battery runs down. This pump
would be the largest appropriate for the hose diameter.

You could put a Tee a couple feet downstream of the vented loop and run the
small pump into that. If only the big pump was running, some water would
divert back into the bilge but, mose likely, the litte pump would already be
working against a leak that was simply faster than it could keep up with.

The ideal thing would be a second line for the primary (small) pump. I
would run this out the counter bottom just ahead of the transom.


I was also thinking about a second pump at some point. Right now, I have two... one for the primary and one for the shower sump. But neither would help much for a major leak.

  #5   Report Post  
posted to rec.boats.cruising
external usenet poster
 
First recorded activity by BoatBanter: Jul 2006
Posts: 674
Default check valve

In article ,
wrote:
On Wed, 02 Jul 2008 21:11:21 -0500, lid (Jonathan
Ganz) wrote:

Here's another pic of the discharge. Not sure why I said it before, but the discharge is on

the starboard side, not the port side. The port side is engine discharge. I must be dyslexic
today.

http://picasaweb.google.com/SailNOW....20431152743042


Congrats on your "funny" this morning!

I had one posted too long ago.


I laughed when my friend sent it too me... haven't see it show it yet here though. I knew it was accepted, but sometimes they change things.





Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is Off
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Double Piloted Check Valve help Larry Boat Building 5 June 24th 06 11:32 PM
Double Piloted Check Valve help Larry Power Boat Racing 0 June 24th 06 06:26 AM
FS: in UK new blakes sea valve daveynews Marketplace 0 July 9th 05 08:23 PM
Need special check valve or water pump Karl Timmermann Electronics 6 June 15th 04 11:37 AM
Where to buy 1" electric valve? William P.N. Smith Electronics 3 May 29th 04 10:13 PM


All times are GMT +1. The time now is 03:27 PM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 BoatBanter.com.
The comments are property of their posters.
 

About Us

"It's about Boats"

 

Copyright © 2017