Home |
Search |
Today's Posts |
|
#1
![]() |
|||
|
|||
![]()
I would recommend you stay away from the teak deck in a boat almost 20
years old. Teak decks, because of the screw holes (used to hold the teak down), are prone to causing saturation and/or delamination of the underlying deck core material unless the boat has been well maintained for the entire 20 years. Just because it looks good doesn't mean that the underlying deck and core are in good condition. Repairing a saturated core is a major (read: expensive) job. The PS Crealock is probably the best quality but, as you are seeing, that comes at a high price. It's also pretty small inside (IMO). Don't compromise on the boat. You can always stretch out the purchase of the extras. Eric "Wendy" wrote in message ... I had a close look at four boats today, all offered through brokers. The experience was a pleasurable one; the brokers were pleasant enough and quite helpful. The weather was a bit cool for my taste, though. Anyway, here's what I looked over in the order in which I saw them, along with my thoughts: Cheoy Lee Pedrick 36, 1985 Model: This boat is simply a very good looking boat; it has loads of visual appeal and has been well-kept. The teak deck is in quite good condition, as are the topside fittings and rigging. Belowdecks, the engine is easily accessible, the cabin layout is sensible and not ostentatiously ornate. She has a genset, which is a plus, but no stove- a definite minus (one could easily be added, however). She's radar-equipped, no SSB or GPS. She would be a fine live-aboard and coastal cruiser, and should handle longer range cruising as the tankage is more than adequate. I'd like to research Cheoy Lee's more; I liked this boat. At an asking price of less than $60,000 she is well within my budget. Pacific Seacraft Crealock 34, 1990 Model: Nice boat; she has a spartan interior and a non-nonsense air about her. This boat is clearly designed for ocean passages. Living aboard would not be difficult, but again the boat is designed to go anywhere, not sit on a dock. At just under $100,000 she is out of my price range, so I didn't really seriously evaluate all her features. Cabo Rico 38, 1981 Model: She was once a nice boat, but neglect has sadly hurt her. The below $80,000 price reflects the condition she's in; it would take a lot of work to bring this boat up to snuff. The teak deck is shot. I would take a pass on this boat; I don't want a project. Tayana 37, 1982 Model: Wonderful boat, she has lots of room and is built like a tank. She has a Perkins, which I like as I have lots of experience with them. She's air-conditioned as well, a must in Texas. Very beamy and not at all claustrophobic, the boat is clearly designed for comfort and safety. She is equipped with a wind generator as well as a wind vane steering system. She has no navigation station; the large quarterberth is designed as an aft stateroom. I would prefer a nav station, but a fold down table sort of thing could be easily added by a carpenter. Electronics consists of an SSB; a radar and GPS system would have to be added (I am a Garmin GPS junkie, I'll freely admit that ![]() within my budget, though I would have to scrape for any planned add-ons. It should be apparent that the first and last boats I looked at were the two which appealed most to me. I have distinct reservations about a teak deck, and while the Cheoy Lee is not the dedicated ocean passage boat that the Tayana is, she would no doubt provide years of performance and satisfaction. The Tayana represents security, comfort, and hominess. She has many of the features I would like in a boat, and probably represents the better investment of the two. It's quite clear to me that I am not exactly sure what I want at this point in time, although I am sure that as I continue to research and actively start sailing that this will become self-evident before I buy. I understand now why searching for a boat can take quite some time. Wendy |
#2
![]() |
|||
|
|||
![]()
The underlayment of teak decks on Tayanas is built up of softwood
squares individually isolated by dams of polyester. If such underlayment does get wet it usually doesnt not spread accross the whole deck as would be the case with ''sheets' of core filler. Not that you cant get a soggy deck on a Tayana; but, if you do the damage wont be as catastrophic as would a deck with continuous underlayment filler. Teak deck maintenance isnt all that bad if you kkep up a gentle and consistent regime of maintenance. Hell, I bet you expend more time scrubbing a glass deck than a teak deck owner does in periodically looking for loose bungs. Give me a teak deck anytime. So what if it makes the boat a bit more top heavy, **nothing** is this world has the non-dkid ability of bare teak. |
#3
![]() |
|||
|
|||
![]()
On Mon, 02 Feb 2004 21:35:11 GMT, Rich Hampel
wrote: The underlayment of teak decks on Tayanas is built up of softwood squares individually isolated by dams of polyester. If such underlayment does get wet it usually doesnt not spread accross the whole deck as would be the case with ''sheets' of core filler. Not that you cant get a soggy deck on a Tayana; but, if you do the damage wont be as catastrophic as would a deck with continuous underlayment filler. Teak deck maintenance isnt all that bad if you kkep up a gentle and consistent regime of maintenance. Hell, I bet you expend more time scrubbing a glass deck than a teak deck owner does in periodically looking for loose bungs. Give me a teak deck anytime. So what if it makes the boat a bit more top heavy, **nothing** is this world has the non-dkid ability of bare teak. The opposing view, and no doubt a boat I would love to visit because it looks so nice. This gentleman knows the problems with teak, knows how to deal with them, knows the best case scenario, and considers the net benefit worth it. I do not, although I've seen nice teak over metal decks that would put me off less than teak over cored decks. To each sailor his or her own. The less wood on the outside, the happier I am, but that's me and is totally from the upkeep point of view. R. |
#4
![]() |
|||
|
|||
![]()
Rich Hampel wrote:
Give me a teak deck anytime. So what if it makes the boat a bit more top heavy, **nothing** is this world has the non-dkid ability of bare teak. I've heard a lot of people say this, but it's not true in my observations. This is probably heresy, but to me it has always seemed like a teak deck is among the worst surfaces. I don't expect anybody else to agree, but I am telling only what I have seen to be true. I've heard "A teak deck is best when barefoot" when it has been proven to me by painful experience that a teak deck will get blistering hot in the southern sun. I've heard "A teak deck is incredible non-skid" said by a crew who had just returned from the foredeck on their hands & knees. In short, I own a boat with a teak deck... they're beautiful but they are not practical in any way... the maintenance is awful, the surface is unreliable, and if it's screwed down over cored fiberglass it's a lurking rot instigator. Our teak deck is coming off in the near future, to be replaced by either plain fiberglass with painted non-skid, or perhaps those industrial textured non-skid materials. wrote: The opposing view, and no doubt a boat I would love to visit because it looks so nice. This gentleman knows the problems with teak, knows how to deal with them, knows the best case scenario, and considers the net benefit worth it. I do not, although I've seen nice teak over metal decks that would put me off less than teak over cored decks. To each sailor his or her own. The less wood on the outside, the happier I am, but that's me and is totally from the upkeep point of view. A little wood here & there is nice, but whole layer of it over the deck is a bit much. Might as well build the whole boat out of the stuff ![]() Fresh Breezes- Doug King |
#5
![]() |
|||
|
|||
![]() "DSK" wrote in message .. . In short, I own a boat with a teak deck... they're beautiful but they are not practical in any way... the maintenance is awful, the surface is unreliable, and if it's screwed down over cored fiberglass it's a lurking rot instigator. Our teak deck is coming off in the near future, to be replaced by either plain fiberglass with painted non-skid, or perhaps those industrial textured non-skid materials. A friend of mine has a Choy Lee that had the deck problem and he removed the teak and replaced it with Treadmaster. I have it on my boat, which I love, but it is awful on bare feet. Leanne s/v Fundy |
#6
![]() |
|||
|
|||
![]()
x-no-archive:yes
"Leanne" wrote: "DSK" wrote in message . .. In short, I own a boat with a teak deck... they're beautiful but they are not practical in any way... the maintenance is awful, the surface is unreliable, and if it's screwed down over cored fiberglass it's a lurking rot instigator. Our teak deck is coming off in the near future, to be replaced by either plain fiberglass with painted non-skid, or perhaps those industrial textured non-skid materials. A friend of mine has a Choy Lee that had the deck problem and he removed the teak and replaced it with Treadmaster. I have it on my boat, which I love, but it is awful on bare feet. I love to go barefoot, and I do not find that Treadmaster is terrible on bare feet. Just very non-slippery. But of course I can walk on gravel barefoot (although I have to be cautious), and I've learned how to walk across a parking lot on a hot day by staying on the white paint lines that mark out the parking spaces. I do draw the line at things like glass, rose bush cuttings and American Chestnut hulls (which have tiny spines) OTOH, my husband doesn't go barefoot at all and has very tender feet. He's pretty AR about not letting anyone on deck with bare feet when underway. And I have proved to myself that the non-Treadmaster parts of the deck are slipperier with bare feet than with shoes. grandma Rosalie |
#7
![]() |
|||
|
|||
![]()
x-no-archive:yes
"Leanne" wrote: "DSK" wrote in message . .. In short, I own a boat with a teak deck... they're beautiful but they are not practical in any way... the maintenance is awful, the surface is unreliable, and if it's screwed down over cored fiberglass it's a lurking rot instigator. Our teak deck is coming off in the near future, to be replaced by either plain fiberglass with painted non-skid, or perhaps those industrial textured non-skid materials. A friend of mine has a Choy Lee that had the deck problem and he removed the teak and replaced it with Treadmaster. I have it on my boat, which I love, but it is awful on bare feet. I love to go barefoot, and I do not find that Treadmaster is terrible on bare feet. Just very non-slippery. But of course I can walk on gravel barefoot (although I have to be cautious), and I've learned how to walk across a parking lot on a hot day by staying on the white paint lines that mark out the parking spaces. I do draw the line at things like glass, rose bush cuttings and American Chestnut hulls (which have tiny spines) OTOH, my husband doesn't go barefoot at all and has very tender feet. He's pretty AR about not letting anyone on deck with bare feet when underway. And I have proved to myself that the non-Treadmaster parts of the deck are slipperier with bare feet than with shoes. grandma Rosalie |
#8
![]() |
|||
|
|||
![]()
"Leanne" wrote in message ...
"DSK" wrote in message .. . In short, I own a boat with a teak deck... they're beautiful but they are not practical in any way... the maintenance is awful, the surface is unreliable, and if it's screwed down over cored fiberglass it's a lurking rot instigator. Our teak deck is coming off in the near future, to be replaced by either plain fiberglass with painted non-skid, or perhaps those industrial textured non-skid materials. A friend of mine has a Choy Lee that had the deck problem and he removed the teak and replaced it with Treadmaster. I have it on my boat, which I love, but it is awful on bare feet. Leanne s/v Fundy I happen to think their is nothing better than a teak deck. You get better traction and their easier on your feet because they have more "give" than a fiberglass deck (we're talking about a "proper" installation here, no fiberglass deck underneath). But the best part about them is the cockpit is much cooler than fiberglass, which is very reflective. Just wet the teak down and it doesn't reflect the sunlight like fiberglass, and the water evaporating from the teak helps keep it cool as well. Also, they don't damage like a fiberglass deck when you drop something heavy on it (put a wet rag over the dented teak and a hot clothes iron on top of the rag, keep wetting the rag, you will be surprised how many dents you can get to come out like this). I admitt it takes a lot of work to keep it looking good, but do a side by side comparison, the teak just looks so much better. As far as having a teak deck over a cored deck, who ever did the job should be hung by his thumbs. That's just a serious problem waiting to happen. |
#9
![]() |
|||
|
|||
![]()
"Leanne" wrote in message ...
"DSK" wrote in message .. . In short, I own a boat with a teak deck... they're beautiful but they are not practical in any way... the maintenance is awful, the surface is unreliable, and if it's screwed down over cored fiberglass it's a lurking rot instigator. Our teak deck is coming off in the near future, to be replaced by either plain fiberglass with painted non-skid, or perhaps those industrial textured non-skid materials. A friend of mine has a Choy Lee that had the deck problem and he removed the teak and replaced it with Treadmaster. I have it on my boat, which I love, but it is awful on bare feet. Leanne s/v Fundy I happen to think their is nothing better than a teak deck. You get better traction and their easier on your feet because they have more "give" than a fiberglass deck (we're talking about a "proper" installation here, no fiberglass deck underneath). But the best part about them is the cockpit is much cooler than fiberglass, which is very reflective. Just wet the teak down and it doesn't reflect the sunlight like fiberglass, and the water evaporating from the teak helps keep it cool as well. Also, they don't damage like a fiberglass deck when you drop something heavy on it (put a wet rag over the dented teak and a hot clothes iron on top of the rag, keep wetting the rag, you will be surprised how many dents you can get to come out like this). I admitt it takes a lot of work to keep it looking good, but do a side by side comparison, the teak just looks so much better. As far as having a teak deck over a cored deck, who ever did the job should be hung by his thumbs. That's just a serious problem waiting to happen. |
#10
![]() |
|||
|
|||
![]() "DSK" wrote in message .. . In short, I own a boat with a teak deck... they're beautiful but they are not practical in any way... the maintenance is awful, the surface is unreliable, and if it's screwed down over cored fiberglass it's a lurking rot instigator. Our teak deck is coming off in the near future, to be replaced by either plain fiberglass with painted non-skid, or perhaps those industrial textured non-skid materials. A friend of mine has a Choy Lee that had the deck problem and he removed the teak and replaced it with Treadmaster. I have it on my boat, which I love, but it is awful on bare feet. Leanne s/v Fundy |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
![]() |
||||
Thread | Forum | |||
Boat fell off trailer | General | |||
4th FL trip report, shorter, this time! | Cruising | |||
I need your advice for a new boat | Cruising | |||
Interesting boat ride...... | General | |||
Sailor's tattoo, must be married too long, Wooden Boat Festival | General |