"Vic Smith" wrote in message
...
On Fri, 22 Jun 2007 15:33:00 +0000, Larry wrote:

I had a string of VWs. 3 bugs, 411 wagon, 2 Kombi campers, one bus...all
great vehicles, but way too much maintenance on the air cooled pancake
engines. All that valve adjusting was way too much.

Had to rebuild mine after the jugs got too big inside. Think I paid
@50 bucks for new jugs with pistons and rings already in them.
Easy job rebuilding them, ground the valves with a reversing drill.
Those engines had a natural life of @60-70k in captivity - the
maintenance you mentioned.
Besides, most I could squeeze out of it was 29 mpg highway.
But the full-sized crap was getting 10-15 mpg, so it was cheap to
run/fix - and easy to park! Mine was a '64. 6 volt.
Had a '67 Squareback too - POS. But it was nice to hear its gas
heater take off like a jet and start steaming up the windows.

--Vic


My brother was a big VW fan. He had numerous 'bugs', an orange
'squareback', a 68 bus and even the 'Thing'.
I bought a '72 Super Beetle brand new and kept it 5 years. That was enough
for me.

"Don White" wrote in
:

My brother was a big VW fan. He had numerous 'bugs', an orange
'squareback', a 68 bus and even the 'Thing'.
I bought a '72 Super Beetle brand new and kept it 5 years. That was
enough for me.


Did any of you guys own an automatic stick shift beetle? I had one of
those. The clutch was a button in the top of the stick shift.

Larry
--
http://www.spp.gov/
The end of the USA and its Constitution....RIP

"Larry" wrote in message
...

Did any of you guys own an automatic stick shift beetle? I had one of
those. The clutch was a button in the top of the stick shift.

Larry


No way....I believe those things were only 2 speed..
I enjoyed the 4 on the floor standard transmission.

On Sat, 23 Jun 2007 00:42:29 +0000, Larry wrote:

"Don White" wrote in
:

My brother was a big VW fan. He had numerous 'bugs', an orange
'squareback', a 68 bus and even the 'Thing'.
I bought a '72 Super Beetle brand new and kept it 5 years. That was
enough for me.


Did any of you guys own an automatic stick shift beetle? I had one of
those. The clutch was a button in the top of the stick shift.

No, mine were manuals. Pretty long-lived. Since you had to pull the
engine to change the clutch out, a good thing.

--Vic

Vic Smith wrote in
:

Since you had to pull the
engine to change the clutch out, a good thing.



That wasn't much of a big deal IF you had the proper engine stand to put
under it on the lift. The dealers pulled them out for the simplest of
reasons.

I was in the Volkswagen Analog Computer Repair Business for a while when
I owned the 411 wagon. My 411 just stopped for no reason in the middle
of traffic. The towtruck took it back to its dealer, with me in a bad
mood. "It's the computer.", the service manager said flatly. He never
even looked at it. He already knew what the problem was. So, I got a
new "computer", an analog device that squirted fuel into its gullet
electrically. It wasn't much of a "computer", nothing digital, just hard
parts! I commandeered my old computer from him before he threw it into a
large pile of computers in a big box in the parts department. LOTS of
computers were tits up, it seemed. No schematic available, of course, I
took it back to my office and pulled it apart and drew my own. I tested
the simple transistors with my Radio Shack in-circuit transistor tester
and found one open, base to collector. I replaced the transistor with a
garden variety 2N2222 that was, in quantity, about 8c in those days. I
swapped it out under the driver's seat and my 411 wagon cranked right up.
I ran it on my home-repaired box, keeping the OEM box as a spare in the
car, just in case. I never had any more trouble with it.

Next time I had it serviced, I told the service manager about my repair,
carefully NOT telling him I knew what was wrong with, at least, my
computer box. "Would you like to repair some more?", he asked. "Sure.",
I replied. I took home about 200 dead boxes from his collection. I went
straight to that one transistor and they were all blown. I replaced a
bunch with 2N2222 generic NPNs and tested them in my 411, all good.

We came to an agreement at $50/unit to repair them. 2 other dealers sent
me their "collections". Anyone trying to pry information about my
repairs got nothing. I'm not shooting my foot. It was easy to open the
box and look at the transistor I replaced. In the next couple of years,
I made a tidy sum out of the repairs from the 3 dealers in just spare
time. I hired some of my tech school students to work on them on
weekends as they backed up. As the model ended, repairs slowed down and
I moved to a better job on the road with Navy contractors so the shop
closed. Every unit but about 3 had all the same blown part....too much
Ic for the little German transistor they were using, melted its
collector. 2N2222 worked great...(c;

Larry
--
http://www.spp.gov/
The end of the USA and its Constitution....RIP

On Sun, 24 Jun 2007 01:17:35 +0000, Larry wrote:

Vic Smith wrote in
:

Since you had to pull the
engine to change the clutch out, a good thing.

That wasn't much of a big deal IF you had the proper engine stand to put
under it on the lift. The dealers pulled them out for the simplest of
reasons.

I had no trouble using just a wheeled floor jack. Once the transaxle
splines are clear of the pressure plate you just lower the engine then
push it off the jack and onto the floor. Then jack up the car's rear
end enough to drag the engine clear. All light duty stuff, no lift
required. Maybe 1/2 an hour after you've done it once.
It's a PITA if the jack is in sand though, which situation I let
myself get into once.

I was in the Volkswagen Analog Computer Repair Business for a while when
I owned the 411 wagon. My 411 just stopped for no reason in the middle
of traffic. The towtruck took it back to its dealer, with me in a bad
mood. "It's the computer.", the service manager said flatly. He never
even looked at it. He already knew what the problem was. So, I got a
new "computer", an analog device that squirted fuel into its gullet
electrically. It wasn't much of a "computer", nothing digital, just hard
parts! I commandeered my old computer from him before he threw it into a
large pile of computers in a big box in the parts department. LOTS of
computers were tits up, it seemed. No schematic available, of course, I
took it back to my office and pulled it apart and drew my own. I tested
the simple transistors with my Radio Shack in-circuit transistor tester
and found one open, base to collector. I replaced the transistor with a
garden variety 2N2222 that was, in quantity, about 8c in those days. I
swapped it out under the driver's seat and my 411 wagon cranked right up.
I ran it on my home-repaired box, keeping the OEM box as a spare in the
car, just in case. I never had any more trouble with it.

Next time I had it serviced, I told the service manager about my repair,
carefully NOT telling him I knew what was wrong with, at least, my
computer box. "Would you like to repair some more?", he asked. "Sure.",
I replied. I took home about 200 dead boxes from his collection. I went
straight to that one transistor and they were all blown. I replaced a
bunch with 2N2222 generic NPNs and tested them in my 411, all good.

We came to an agreement at $50/unit to repair them. 2 other dealers sent
me their "collections". Anyone trying to pry information about my
repairs got nothing. I'm not shooting my foot. It was easy to open the
box and look at the transistor I replaced. In the next couple of years,
I made a tidy sum out of the repairs from the 3 dealers in just spare
time. I hired some of my tech school students to work on them on
weekends as they backed up. As the model ended, repairs slowed down and
I moved to a better job on the road with Navy contractors so the shop
closed. Every unit but about 3 had all the same blown part....too much
Ic for the little German transistor they were using, melted its
collector. 2N2222 worked great...(c;

Cool. Sometimes I wish I learned more about electronics, but my color
perception kept me on wrenches. I'll just refer to your posts when I
need electronics advice.

--Vic

"Vic Smith" wrote in message
...
On Sun, 24 Jun 2007 01:17:35 +0000, Larry wrote:

Vic Smith wrote in
m:

Since you had to pull the
engine to change the clutch out, a good thing.

That wasn't much of a big deal IF you had the proper engine stand to put
under it on the lift. The dealers pulled them out for the simplest of
reasons.

I had no trouble using just a wheeled floor jack. Once the transaxle
splines are clear of the pressure plate you just lower the engine then
push it off the jack and onto the floor. Then jack up the car's rear
end enough to drag the engine clear. All light duty stuff, no lift
required. Maybe 1/2 an hour after you've done it once.
It's a PITA if the jack is in sand though, which situation I let
myself get into once.

I was in the Volkswagen Analog Computer Repair Business for a while when
I owned the 411 wagon. My 411 just stopped for no reason in the middle
of traffic. The towtruck took it back to its dealer, with me in a bad
mood. "It's the computer.", the service manager said flatly. He never
even looked at it. He already knew what the problem was. So, I got a
new "computer", an analog device that squirted fuel into its gullet
electrically. It wasn't much of a "computer", nothing digital, just hard
parts! I commandeered my old computer from him before he threw it into a
large pile of computers in a big box in the parts department. LOTS of
computers were tits up, it seemed. No schematic available, of course, I
took it back to my office and pulled it apart and drew my own. I tested
the simple transistors with my Radio Shack in-circuit transistor tester
and found one open, base to collector. I replaced the transistor with a
garden variety 2N2222 that was, in quantity, about 8c in those days. I
swapped it out under the driver's seat and my 411 wagon cranked right up.
I ran it on my home-repaired box, keeping the OEM box as a spare in the
car, just in case. I never had any more trouble with it.

Next time I had it serviced, I told the service manager about my repair,
carefully NOT telling him I knew what was wrong with, at least, my
computer box. "Would you like to repair some more?", he asked. "Sure.",
I replied. I took home about 200 dead boxes from his collection. I went
straight to that one transistor and they were all blown. I replaced a
bunch with 2N2222 generic NPNs and tested them in my 411, all good.

We came to an agreement at $50/unit to repair them. 2 other dealers sent
me their "collections". Anyone trying to pry information about my
repairs got nothing. I'm not shooting my foot. It was easy to open the
box and look at the transistor I replaced. In the next couple of years,
I made a tidy sum out of the repairs from the 3 dealers in just spare
time. I hired some of my tech school students to work on them on
weekends as they backed up. As the model ended, repairs slowed down and
I moved to a better job on the road with Navy contractors so the shop
closed. Every unit but about 3 had all the same blown part....too much
Ic for the little German transistor they were using, melted its
collector. 2N2222 worked great...(c;

Cool. Sometimes I wish I learned more about electronics, but my color
perception kept me on wrenches. I'll just refer to your posts when I
need electronics advice.

--Vic

Vic, bad boys rape all our young girls, but Violet gives willingly, get some
now.

"Capt. Lewry" wrote in message
t...

"Vic Smith" wrote in message
...
On Sun, 24 Jun 2007 01:17:35 +0000, Larry wrote:

Vic Smith wrote in
:

Since you had to pull the
engine to change the clutch out, a good thing.

That wasn't much of a big deal IF you had the proper engine stand to put
under it on the lift. The dealers pulled them out for the simplest of
reasons.

I had no trouble using just a wheeled floor jack. Once the transaxle
splines are clear of the pressure plate you just lower the engine then
push it off the jack and onto the floor. Then jack up the car's rear
end enough to drag the engine clear. All light duty stuff, no lift
required. Maybe 1/2 an hour after you've done it once.
It's a PITA if the jack is in sand though, which situation I let
myself get into once.

I was in the Volkswagen Analog Computer Repair Business for a while when
I owned the 411 wagon. My 411 just stopped for no reason in the middle
of traffic. The towtruck took it back to its dealer, with me in a bad
mood. "It's the computer.", the service manager said flatly. He never
even looked at it. He already knew what the problem was. So, I got a
new "computer", an analog device that squirted fuel into its gullet
electrically. It wasn't much of a "computer", nothing digital, just hard
parts! I commandeered my old computer from him before he threw it into a
large pile of computers in a big box in the parts department. LOTS of
computers were tits up, it seemed. No schematic available, of course, I
took it back to my office and pulled it apart and drew my own. I tested
the simple transistors with my Radio Shack in-circuit transistor tester
and found one open, base to collector. I replaced the transistor with a
garden variety 2N2222 that was, in quantity, about 8c in those days. I
swapped it out under the driver's seat and my 411 wagon cranked right up.
I ran it on my home-repaired box, keeping the OEM box as a spare in the
car, just in case. I never had any more trouble with it.

Next time I had it serviced, I told the service manager about my repair,
carefully NOT telling him I knew what was wrong with, at least, my
computer box. "Would you like to repair some more?", he asked. "Sure.",
I replied. I took home about 200 dead boxes from his collection. I went
straight to that one transistor and they were all blown. I replaced a
bunch with 2N2222 generic NPNs and tested them in my 411, all good.

We came to an agreement at $50/unit to repair them. 2 other dealers sent
me their "collections". Anyone trying to pry information about my
repairs got nothing. I'm not shooting my foot. It was easy to open the
box and look at the transistor I replaced. In the next couple of years,
I made a tidy sum out of the repairs from the 3 dealers in just spare
time. I hired some of my tech school students to work on them on
weekends as they backed up. As the model ended, repairs slowed down and
I moved to a better job on the road with Navy contractors so the shop
closed. Every unit but about 3 had all the same blown part....too much
Ic for the little German transistor they were using, melted its
collector. 2N2222 worked great...(c;

Cool. Sometimes I wish I learned more about electronics, but my color
perception kept me on wrenches. I'll just refer to your posts when I
need electronics advice.

--Vic

Vic, bad boys rape all our young girls, but Violet gives willingly, get
some now.

Larry, The way we taught it was Violet gives willingly for gold or silver.
Now don't ask about Oscar in the trig functions. Teaching was fun, but it
got old at
TCL ( Technical College of the Low Country). At NATTC, I had a captive
audience and
they had the incentive to learn the avionics stuff or end up as paint
chippers on some tin can.

Leanne

Leanne

Vic Smith wrote in
:

Cool. Sometimes I wish I learned more about electronics, but my color
perception kept me on wrenches. I'll just refer to your posts when I
need electronics advice.

--Vic



I fail every depth perception test ever given to me. Charleston Naval
Shipyard nearly let me go the first time I failed the test, until my
bosses put a stop to it because of my troubleshooting abilities and the
fact that I came in 2nd in the microminiature soldering school...(c;

I don't know how I can solder a tiny wire the width of a hair with no
depth perception. I just don't have it.....???

Larry
--
http://www.spp.gov/
The end of the USA and its Constitution....RIP

In article ,
Larry wrote:

I fail every depth perception test ever given to me. Charleston Naval
Shipyard nearly let me go the first time I failed the test, until my
bosses put a stop to it because of my troubleshooting abilities and the
fact that I came in 2nd in the microminiature soldering school...(c;

I don't know how I can solder a tiny wire the width of a hair with no
depth perception. I just don't have it.....???

Larry

Don't feel bad Larry, I have been Color Blind since I was 12 years old...
For a RadioMan & Telecommunications Tech, that makes kind of HARD to do
Color Codes, and 500 Pair Wire Splices. I just compensate by ALWAYS
having a very Bright Flashlight in the toolpouch, and with Color
Corrective Glasses, for the last Decade, I can get along.....

Bruce in alaska
--
add a 2 before @