On Feb 17, 4:32 pm, Harlan Lachman wrote:
I have been intrigued by the discussion of anchoring -- especially the
thought of rigging an anchor so one can drop it off the bow from the
cockpit. Thinking about spin pole, cleats, hatches, etc., I wonder if
anyone has figured out the best ways to accomplish this maneuver with
the least risk. And how early in the game did they rig their anchor set
up.

harlan

--
To respond, obviously drop the "nospan"?

You just use a power windlass with a self dropping anchor with a up/
down switch at the helm.

"capt.bill" wrote:
You just use a power windlass with a self dropping anchor with a up/
down switch at the helm.

Every self respecting 100' yacht should have one ;-)
Seriously though, on a small boat, say 25' or less, I've found a
windlass can be more trouble than it's worth.

Rick

"capt.bill11" wrote:
You just use a power windlass with a self dropping anchor with a up/
down switch at the helm.

Every self respecting 100' yacht should have one ;-)
Seriously though, on smallish boats, say 25' or less, I've found a
windlass to be more trouble than it's worth.

Rick

On Feb 17, 6:27 pm, wrote:
"capt.bill11" wrote:
You just use a power windlass with a self dropping anchor with a up/
down switch at the helm.

Every self respecting 100' yacht should have one ;-)
Seriously though, on smallish boats, say 25' or less, I've found a
windlass to be more trouble than it's worth.

Rick

:-)

Nice to see someone get the joke without the need for a ":-)" all the
time.

In article ,
lid wrote:

"capt.bill11" wrote:
You just use a power windlass with a self dropping anchor with a up/
down switch at the helm.

Every self respecting 100' yacht should have one ;-)
Seriously though, on smallish boats, say 25' or less, I've found a
windlass to be more trouble than it's worth.

Rick

I agree, except for the size. I have found windlasses to be a bother
with modern designs at 32' or below, say about 5 tons. In the rare cases
where we're leaving an anchorage in enough wind to make hauling
difficult, either Pat twiddles the motor controls or I shift the rode to
the stern and haul with the genny winch.

--
Jere Lull
Xan-a-Deux ('73 Tanzer 28 #4 out of Tolchester, MD)
Xan's NEW Pages: http://web.mac.com/jerelull/iWeb/Xan/
Our BVI FAQs (290+ pics) http://homepage.mac.com/jerelull/BVI/

"Jere Lull" skrev i en meddelelse
...
In article ,
lid wrote:

"capt.bill11" wrote:
You just use a power windlass with a self dropping anchor with a up/
down switch at the helm.

SNIP

I agree, except for the size. I have found windlasses to be a bother
with modern designs at 32' or below, say about 5 tons. In the rare
cases
where we're leaving an anchorage in enough wind to make hauling
difficult, either Pat twiddles the motor controls or I shift the rode
to
the stern and haul with the genny winch.

How do you handle this situation, if you're the only person on the boat?
I mean, how do you get the anchor in place with the chain/rode, without
damaging the freeboard?

--
Flemming Torp
Gimle/DEN-61

In article ,
"Flemming Torp" fletopkanelbolle2rp.danmark wrote:

In the rare cases where we're leaving an anchorage in enough wind
to make hauling difficult, either Pat twiddles the motor controls
or I shift the rode to the stern and haul with the genny winch.

How do you handle this situation, if you're the only person on the
boat? I mean, how do you get the anchor in place with the chain/rode,
without damaging the freeboard?

Lead the free rode back to the aft fairlead and winch, release the rode
at the bow & haul.

Truth be told, I did that only for practice as it's messy and I hardly
ever find myself needing to leave an anchorage in winds that high. DID
do it a couple of times to free a very deeply set anchor.

About my most difficult hand-haul was in the BVI on a Beneteau 33 in
about 25 knots (Christmas winds). By simply hauling only when the rode
was a little freer from our sailing around, snubbing the rest of the
time, it didn't take much effort, though it took a while.

If I'm in a hurry, I'll lash the tiller amidships, put the engine in
gear just enough to ease the tension slightly, then haul from the bow.
Once we're *near* free, I'll walk back, kick the boat out of gear, then
finish up on the anchor. It's easy to bring an anchor in from about 2:1
if there's any wave action, which you'll have in those winds.

--
Jere Lull
Xan-a-Deux ('73 Tanzer 28 #4 out of Tolchester, MD)
Xan's NEW Pages: http://web.mac.com/jerelull/iWeb/Xan/
Our BVI FAQs (290+ pics) http://homepage.mac.com/jerelull/BVI/

"Jere Lull" skrev i en meddelelse
...
In article ,
"Flemming Torp" fletopkanelbolle2rp.danmark wrote:

In the rare cases where we're leaving an anchorage in enough wind
to make hauling difficult, either Pat twiddles the motor controls
or I shift the rode to the stern and haul with the genny winch.

How do you handle this situation, if you're the only person on the
boat? I mean, how do you get the anchor in place with the chain/rode,
without damaging the freeboard?

Lead the free rode back to the aft fairlead and winch, release the
rode
at the bow & haul.

SNIP

If I'm in a hurry, I'll lash the tiller amidships, put the engine in
gear just enough to ease the tension slightly, then haul from the bow.
Once we're *near* free, I'll walk back, kick the boat out of gear,
then
finish up on the anchor. It's easy to bring an anchor in from about
2:1
if there's any wave action, which you'll have in those winds.

Thank you for your explanation. The last idea, I have tried with some
success ... but my back does not like it ...

Due to language problems on my part, I'm sure I fully understand your
first procedure, because, I don't know, what a fairled is ... Sorry. Is
it some kind of wheel og "thing", that keeps the rode/chain and the
anchor free of the side/stern? What I find pretty difficult is not to
scratch the glass fibre side (called freeboard?), when i use the winch
for the spinaker/genua. Hauling from the bow, the rode and the anchor
goes (almost) free of the sides of the boat.

--
Flemming Torp
Gimle/DEN-61

Sorry for misformulation ... see below ...

"Flemming Torp" fletopkanelbolle2rp.danmark skrev i en meddelelse
. ..

"Jere Lull" skrev i en meddelelse
...
In article ,
"Flemming Torp" fletopkanelbolle2rp.danmark wrote:

In the rare cases where we're leaving an anchorage in enough wind
to make hauling difficult, either Pat twiddles the motor controls
or I shift the rode to the stern and haul with the genny winch.

How do you handle this situation, if you're the only person on the
boat? I mean, how do you get the anchor in place with the
chain/rode,
without damaging the freeboard?

Lead the free rode back to the aft fairlead and winch, release the
rode
at the bow & haul.

SNIP

If I'm in a hurry, I'll lash the tiller amidships, put the engine in
gear just enough to ease the tension slightly, then haul from the
bow.
Once we're *near* free, I'll walk back, kick the boat out of gear,
then
finish up on the anchor. It's easy to bring an anchor in from about
2:1
if there's any wave action, which you'll have in those winds.

Thank you for your explanation. The last idea, I have tried with some
success ... but my back does not like it ...

Due to language problems on my part, I'm sure I fully understand your

Unfortunately, I've forgotten a not ... so the meaning is:

I'm *not* sure I fully understand your .... sorry for the confusion ...

first procedure, because, I don't know, what a fairled is ... Sorry.
Is it some kind of wheel og "thing", that keeps the rode/chain and the
anchor free of the side/stern? What I find pretty difficult is not to
scratch the glass fibre side (called freeboard?), when i use the winch
for the spinaker/genua. Hauling from the bow, the rode and the anchor
goes (almost) free of the sides of the boat.

--
Flemming Torp
Gimle/DEN-61

"Jere Lull" wrote:
Once we're *near* free, I'll walk back, kick the boat out of gear,
then
finish up on the anchor. It's easy to bring an anchor in from about
2:1
if there's any wave action, which you'll have in those winds.

"Flemming Torp" wrote:
Thank you for your explanation. The last idea, I have tried with some
success ... but my back does not like it ...

Don't use your back. Just take a wrap around the cleat or Sampson
post or whatever you have there. Take up the slack as the bow falls
and just hold the wrap as the bow rises. Let the boat do the back
breaking work. Once the anchor pops free, you can haul it in no prob.

Rick