Home |
Search |
Today's Posts |
#21
posted to rec.boats.cruising,uk.rec.sailing
|
|||
|
|||
Volvo MD7A overheating
On Sun, 21 Dec 2008 22:45:50 -0800 (PST),
wrote: This installation diagram from Vetus on their water strainer specifically shows that the strainer be at least 15cm / 6" ABOVE the waterline. http://www.vetusweb.com/manuals/file...01%2007-07.pdf Probably because their strainer has a plastic top (polycarbonate) which I regard as unseaworthy. Proper marine strainers look like this: http://marineengineparts.com/shopsit...l/page515.html |
#22
posted to rec.boats.cruising,uk.rec.sailing
|
|||
|
|||
Volvo MD7A overheating
Bruce In Bangkok wrote:
On Sun, 21 Dec 2008 22:45:50 -0800 (PST), wrote: This installation diagram from Vetus on their water strainer specifically shows that the strainer be at least 15cm / 6" ABOVE the waterline. http://www.vetusweb.com/manuals/file...01%2007-07.pdf Yes it does but I can see no reason for it. To clean the filter you turn the sea cock off so that can't be the reason Yes it can be, but it probably isn't the only reason. Doing it this way means you don't *have to* close the seacock when cleaning the filter, although it is of course good practice to do so anyway. If the strainer is mounted above the waterline, then it's easier to see whether it even needs cleaning, without having to bend down and put your head and an inspection lamp into a difficult to get at space. A few more reasons: (1) If the strainer lid leaks slightly (this should never happen, but it could), then if it's below the waterline you will get water coming into the boat unless you close the seacock every time you stop the engine (and if you do that, you have to remember to open it every time you start the engine). Most people don't do that, they only close seacocks when leaving the boat unattended for a prolonged period (more than a few hours). (2) If the strainer is mounted above the waterline, it's likely to be in a more visible position, and will have some air in the top. This makes it easy to tell visually how well the pump is sucking, from the gush of water coming up the feed pipe and splashing against the underside of the strainer lid. This is sometimes easier than looking for water coming out of the exhaust. (3) If it's ever necessary to prime the pump manually, this is more easily done if it's above the pump: just open the strainer lid and pour water in. and the way it is specified every engine start is with a dry impeller in the pump. This is not actually true. Typically the hose from strainer to pump is always full of water, and so is part (maybe half) of the strainer body. |
#23
posted to rec.boats.cruising,uk.rec.sailing
|
|||
|
|||
Volvo MD7A overheating
Wayne.B wrote:
On Sun, 21 Dec 2008 22:45:50 -0800 (PST), wrote: This installation diagram from Vetus on their water strainer specifically shows that the strainer be at least 15cm / 6" ABOVE the waterline. http://www.vetusweb.com/manuals/file...01%2007-07.pdf Probably because their strainer has a plastic top (polycarbonate) which I regard as unseaworthy. Proper marine strainers look like this: http://marineengineparts.com/shopsit...l/page515.html The removable glass cyclinders don't look much less seaworthy. If you want a really proper one, get one which is all bronze, like this: http://www.gaelforcemarine.co.uk/Pum...isherman-Model |
#24
posted to rec.boats.cruising,uk.rec.sailing
|
|||
|
|||
Volvo MD7A overheating
In message , hpeer
writes I have Volvo MD7A, 13 hp two cylinder unit with salt water cooling. Runs perfectly with one exception, it occasionally overheats and I can't figure out what the heck is going on. I bought the boat used and the previous owner had fitter her out himself. Every time she overheats, I find something to "fix" after which she is fine for a spell then she will overheat again. Clearly I'm not getting to the root cause. Generally she will seem to be running along just fine and all of a sudden the pressure gauge just goes up, up, up. It seems to be a bi-state kind of thing, it either works perfectly well or not at all. Its almost as if there is a ball valve or something somewhere that is sticking. It's obviously not a bad gage. The plumbing goes like this: Through hull fitting Salt water strainer Tap to the transmission/engine Tap to secondary pick up from bilge Tap to sinks Here is some of the history and what I had done, in each case I have also checked/changed the impeller. They usually look just perfect. 1: Recently fitted salt water strainer seemed to be blocked with debris from its construction. It is home built out of some interlocking pieces of PVC pipe, the inner piece has a zillion small holes drilled in it. I dumped this stuff out and she was fine. 2: Found a small leak in the copper pipe from the transmission to the impeller. I thought that maybe it was sucking in air and the impeller was getting air bound. Repaired the leak. 3: Moved and lowered the salt water strainer. This was mounted pretty high on a bulkhead with real long hoses. I moved it to the engine compartment and lowered it. I thought that maybe there was just too much suction head to get the water going. 4: Threw thermostat overboard. Any clues? You've had many replies - and good clues to look for. Whilst at it, I would look at your flexible exhaust - if this has laminated and partially blocked the exit it will cause overheating. And it likely has laminated if you've overheated.. -- Keith replace nospam with ilf0rd |
#25
posted to rec.boats.cruising,uk.rec.sailing
|
|||
|
|||
Volvo MD7A overheating
"Bruce In Bangkok" wrote in message
... On Sun, 21 Dec 2008 22:45:50 -0800 (PST), wrote: This installation diagram from Vetus on their water strainer specifically shows that the strainer be at least 15cm / 6" ABOVE the waterline. http://www.vetusweb.com/manuals/file...01%2007-07.pdf MW Yes it does but I can see no reason for it. To clean the filter you turn the sea cock off so that can't be the reason and the way it is specified every engine start is with a dry impeller in the pump. Doesn't make sense to me... unless you like to change pump impellers. Cheers, Bruce (bruceinbangkokatgmaildotcom) My strainer is well above the water line, and I don't have to turn off the seacock to clean the strainer. The out from the strainer holds water against the impeller, so it's never without a water start... -- "j" ganz @@ www.sailnow.com |
#26
posted to rec.boats.cruising,uk.rec.sailing
|
|||
|
|||
Volvo MD7A overheating
"Ronald Raygun" wrote in message
... Wayne.B wrote: On Sun, 21 Dec 2008 22:45:50 -0800 (PST), wrote: This installation diagram from Vetus on their water strainer specifically shows that the strainer be at least 15cm / 6" ABOVE the waterline. http://www.vetusweb.com/manuals/file...01%2007-07.pdf Probably because their strainer has a plastic top (polycarbonate) which I regard as unseaworthy. Proper marine strainers look like this: http://marineengineparts.com/shopsit...l/page515.html The removable glass cyclinders don't look much less seaworthy. If you want a really proper one, get one which is all bronze, like this: http://www.gaelforcemarine.co.uk/Pum...isherman-Model Maybe, but then you can't see what's going on without opening it up. With the clear one, you can see if there's debris with the engine running. Can't imagine what would break the glass in anything other than extraordinary circumstances. Then, you probably have bigger problems anyway. -- "j" ganz @@ www.sailnow.com |
#27
posted to rec.boats.cruising,uk.rec.sailing
|
|||
|
|||
Volvo MD7A overheating
Capt. JG wrote:
"Ronald Raygun" wrote in message ... Wayne.B wrote: Probably because their strainer has a plastic top (polycarbonate) which I regard as unseaworthy. Proper marine strainers look like this: http://marineengineparts.com/shopsit...l/page515.html The removable glass cyclinders don't look much less [un]seaworthy. If you want a really proper one, get one which is all bronze, like this: http://www.gaelforcemarine.co.uk/Pum...isherman-Model Maybe, but then you can't see what's going on without opening it up. With the clear one, you can see if there's debris with the engine running. True. Can't imagine what would break the glass in anything other than extraordinary circumstances. Then, you probably have bigger problems anyway. Well, I would imagine that anything which would break the polycarbonate would also break the glass. |
#28
posted to rec.boats.cruising,uk.rec.sailing
|
|||
|
|||
Volvo MD7A overheating
hpeer wrote:
I have Volvo MD7A, 13 hp two cylinder unit with salt water cooling. Runs perfectly with one exception, it occasionally overheats and I can't figure out what the heck is going on. I bought the boat used and the previous owner had fitter her out himself. Every time she overheats, I find something to "fix" after which she is fine for a spell then she will overheat again. Clearly I'm not getting to the root cause. Generally she will seem to be running along just fine and all of a sudden the pressure gauge just goes up, up, up. It seems to be a bi-state kind of thing, it either works perfectly well or not at all. Its almost as if there is a ball valve or something somewhere that is sticking. It's obviously not a bad gage. The plumbing goes like this: Through hull fitting Salt water strainer Tap to the transmission/engine Tap to secondary pick up from bilge Tap to sinks Here is some of the history and what I had done, in each case I have also checked/changed the impeller. They usually look just perfect. 1: Recently fitted salt water strainer seemed to be blocked with debris from its construction. It is home built out of some interlocking pieces of PVC pipe, the inner piece has a zillion small holes drilled in it. I dumped this stuff out and she was fine. 2: Found a small leak in the copper pipe from the transmission to the impeller. I thought that maybe it was sucking in air and the impeller was getting air bound. Repaired the leak. 3: Moved and lowered the salt water strainer. This was mounted pretty high on a bulkhead with real long hoses. I moved it to the engine compartment and lowered it. I thought that maybe there was just too much suction head to get the water going. 4: Threw thermostat overboard. Any clues? Many thanks, Howard With that history, the impeller is almost certainly junk. Replace it every three years minimum or after *any* serious overheat. If you've got a delaminated hose, its interior may be collapsing under suction with nothing visible on the outside, blocking all flow. It will spring back when the engine is off, either immediately or when disturbed. With an intermittant problem like this, replace *all* hoses between the intake and the water pump if there is *any* sign of distortion or they are over about 5 years old with suction rated hose. The collapse would be triggered by a momentary obstruction e.g. a plastic bag or clump of seaweed over the intake which washes clear as soon as the hose collapses. On many engines removing the thermostat *will* result in cooling problems. Any bypass type thermostat *MUST* be in place for proper cooling and even a direct flow thermostat (only two ports on its chamber) can give trouble if missing. A seawater thermostat is easy enough to test in a pan of water on the stove so deep sixing it was not so smart. In an emergency, for a direct flow system, snipping out the central plunger will let you make a long motor passage to reach port with a failed thermostat, but if totally removed you should consider it harbour use only. Some engines will run happily with no thermostat but it all depends on the design of the water jacket and should *never* be counted on). For a bypass thermostat (3 port chamber) in an emergency either wedge it wide open, or you have to plug the bypass hoze. I belive your thermostat housing has a 1/4 inch bypass port and I have heard that it also doesn't seal properly without a thermostat in. It doesn't matter if the strainer is below or slightly above the water line so long as its absolutely air tight, and there is more water volume in the hose to the water pump than the volume of the strainer + the volume of that part of the intake above the waterline. Its going to have a bubble anyway and if you really want to be able to quickly visually check the flow in a large clear lidded strainer put a pingpong ball in there, ideally with half of it coloured black in sectors to make it easier to see it move. Personally I'd prefer below the waterline, with a nylon or marelon pipe coupler to join its intake and outlet hoses cable-tied to it for emergency repairs. The standup bronze one on the seacock, you can just shove a tapered bung into which should be there anyway. No air leaks or restrictions other than the strainer can be tolerated at all between the intake and the pump. You should remove the tap to the bilge and the galley and connect direct to the seacock. If the problem is solved, I *might* consider reconnecting the bilge pickup, but the amount of emergency seawater pumping this gives you is minimal and a large mechanically or electrically driven pump would be a far better idea. You can even get a dewatering pump that permanently clamps round your propshaft and acts as a bilge blower as long as the water is below its housing. Google 'Ericson Safety Pump'. Unless one has a seawater manifold with an intake of at least 3 times the total area of *all* pipes off it, it is an extremely bad idea to tee *anything* off the engine cooling intake. The additional risk due to a properly installed and maintained seacock for the galley in a protected location is negligible, and it can be easily and properly fitted in a couple of hour yourself for less than a affordable meal out for two. If you are concerned about cooling flow, one of the simplest ways of monitoring it is to run a small bore pipe from the vent spigot on a non-valved vented loop between the engine and the injection elbow to a little telltale just over one of the cockpit drains, NOT an external through hull, so you can see there is adequate cooling at any time. If, as I do, you have a bronze strainer with wing nuts (actually wing bolts on mine), keep some spares. The one time you are under pressure to clear it, you'll loose a nut down the bildge. . . :-( You've probably got a partially blocked water jacket on the manifold or block. It will require acid flushing. I've had good results with a formic acid based kettle descaler which is less aggressive than the hydrochloric acid based products so safer for pumps, thermostats etc. There are various methods of flushing ranging from a static soak followed by hoseing out to running the engine while circulating the acid solution, best ask here for further advice. A dilute Phosphoric acid (Jenolite or milk stone remover) flush after you've got the rust and lime out will convert remaining rust to Iron Phosphate, reducing the risk of further rusting. Volvo used to recommend inhibiting the cooling system with a soluable oil when laying up. P.S. there is an engine workshop manual he http://www.bluemoment.com/manuals/Vo...A_Workshop.pdf |
#29
posted to rec.boats.cruising,uk.rec.sailing
|
|||
|
|||
Volvo MD7A overheating
"Ronald Raygun" wrote in message
m... Capt. JG wrote: "Ronald Raygun" wrote in message ... Wayne.B wrote: Probably because their strainer has a plastic top (polycarbonate) which I regard as unseaworthy. Proper marine strainers look like this: http://marineengineparts.com/shopsit...l/page515.html The removable glass cyclinders don't look much less [un]seaworthy. If you want a really proper one, get one which is all bronze, like this: http://www.gaelforcemarine.co.uk/Pum...isherman-Model Maybe, but then you can't see what's going on without opening it up. With the clear one, you can see if there's debris with the engine running. True. Can't imagine what would break the glass in anything other than extraordinary circumstances. Then, you probably have bigger problems anyway. Well, I would imagine that anything which would break the polycarbonate would also break the glass. In my case, the strainer is about chest high when I'm standing in the cabin. It's just behind the forward firewall above the top of the steps just to port of the sink. It would take a lot to break it from the firewall side. On the engine side of the strainer, there's open space above the engine. Probably my biggest concern is bumping it when I completely remove a small drawer above the top step, but it's a minor concern. -- "j" ganz @@ www.sailnow.com |
#30
posted to rec.boats.cruising,uk.rec.sailing
|
|||
|
|||
Volvo MD7A overheating
Keith wrote:
Whilst at it, I would look at your flexible exhaust - if this has laminated and partially blocked the exit it will cause overheating. And it likely has laminated if you've overheated.. With respect, DEELAMINATED. Laminated is sticking something together in layers, delaminated is when they come apart. You'll also get horrible black smoke at full throttle if the exhaust is significantly restricted. The water trap (water lift muffler) may also be damaged by overheating and causing a blockage, but in the absense of symptoms like limited power and smoke, I'd suspect something upstream of the exhaust first. Some designs of injection elbow are prone to blicking by rust flakes. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Volvo Penta V8 Overheating | General | |||
Volvo MD7A raw-water cooling flush | General | |||
Volvo MD7A raw-water cooling flush | General | |||
Volvo MD7A and MD5A difference?? | Cruising | |||
Need Exhaust Manifold (volvo MD7A) | Cruising |