My boat (Foxcub 18) has some leaks in the topsides, where the shrouds come
down to the deck. The shrouds attach to U-bolts which pass through the edge
of the deck to a blind fixing inside. After messing about with a hose, it
appears that water is getting through between the U-bolts and GRP.

Since the fixings don't seem to be removable, I'm thinking of sealing them
from above, using some sort of mastic or highly-flexible sealant, perhaps
squeezed in with a syringe. What would be a good material to use? Any other
way of fixing the problem?


--
Wally
www.artbywally.com
www.wally.myby.co.uk

Since the fixings don't seem to be removable, I'm thinking of sealing them
from above, using some sort of mastic or highly-flexible sealant, perhaps


Wally, you're going to get plenty of real advise on this one, so I don't feel
there's anything wrong with me pointing out that you're a royal putz who
shouldn't be allowed to own a boat.
Non removable fixings????

Bwahahahahahahaha!

RB

Bobsprit wrote:

Wally, you're going to get plenty of real advise on this one, so I
don't feel there's anything wrong with me pointing out that you're a
royal putz who shouldn't be allowed to own a boat.
Non removable fixings????

Bwahahahahahahaha!

Thank you for offering such unmitigated support to a sweet, innocent,
fresh-faced n00b. If I'm ever in NY, remind me to give your boatload of
waif-and-stray skanks a wide berth.


--
Wally
www.artbywally.com
www.wally.myby.co.uk

Thank you for offering such unmitigated support to a sweet, innocent,
fresh-faced n00b.

Wally, a few moments of research could produce the info you want. You might
also join a few of the Sailnet groups which could provide you with FAR more
genuine info that this group can provide.
If you want a "proper" repair, you need to rebed those U bolts, even if you
have to cut them out. It's done all the time on low-end boats. Most recently I
watched a guy do exactly that job on a small Chrysler boat. But wouldn't you
prefer more feedback from a far bigger group that this one?
Get a clue, Wally. Puh-lease!

RB

Bobsprit wrote:

Wally, you're going to get plenty of real advise on this one

And Bobsprit also wrote:

... join a few of the Sailnet groups which could provide you
with FAR more genuine info that this group can provide.

You're contradicting yourself.


If you want a "proper" repair, you need to rebed those U bolts, even
if you have to cut them out. It's done all the time on low-end boats.
Most recently I watched a guy do exactly that job on a small Chrysler
boat.

The boat has a cabin lining which is a single-piece GRP moulding. There's an
air gap between this and the hull, and I can just get my fingers into the
gap, accessed from inside the settee berth. I used a little mirror to try
and get a look, and I can just see the inside of one of the U-bolts (three
per side). I reckon the chances of getting at the nuts with a socket set are
somewhere between minimal to hopeless, so I'm going to look into the
possibility of cutting apertures in the liner to gain access that way.
There's a glued-on moulded shelf on the liner where I'd want to do the
cutting, so I need to try and get that off first.


But wouldn't you prefer more feedback from a far bigger group
that this one?

Get a clue, Wally. Puh-lease!

Lame.


--
Wally
www.artbywally.com
www.wally.myby.co.uk

The boat has a cabin lining which is a single-piece GRP moulding.


Okay, so they put in the bolts, then glued or riveted the liner in. The liner
won't come down and you can't slip a wrench in their to grab a bolt. You'd
never get a bolt back on anyway in that case. That sucks. But cutting access
areas into the liner is a good idea. A Roto Zip tool (use the depth setting)
can make this a neat job. Set the depth to JUST through the depth of the liner.
You could then make teak plugs for the holes you made later on. Be careful not
to cut right up through the deckside!
Do it slowly and plan it carefull to avoid a mishap that will leave you with a
larger repair and glass work.
Why not take pics of this job before and after. Done right, you'll have made a
nice repair and an improvement to her that will help sell her when that day
comes.

Good Luck,

RB

"Bobsprit" wrote ...

Wally, I used duct tape on my boat. Stopped the leaks and looks
really cool.

BS

Wally wrote:
My boat (Foxcub 18) has some leaks in the topsides, where the shrouds come
down to the deck. The shrouds attach to U-bolts which pass through the edge
of the deck to a blind fixing inside. After messing about with a hose, it
appears that water is getting through between the U-bolts and GRP.

Since the fixings don't seem to be removable, I'm thinking of sealing them
from above, using some sort of mastic or highly-flexible sealant, perhaps
squeezed in with a syringe. What would be a good material to use? Any other
way of fixing the problem?

Squeezing in miracle goop from above is doubtful. Is there any way of
taking the nuts & backing plates off the underside? That way you could
clean out all the old goop... somebody is sure to have squeezed some in
from above, at some point in the past... maybe it even worked for a
while... and start fresh. Lately I've been using 3M 4200 UV-resistant.
Works well on everything I've rebedded so far.

Fresh Breezes- Doug King

DSK wrote:

Squeezing in miracle goop from above is doubtful. Is there any way of
taking the nuts & backing plates off the underside?

See post to Bob - no way of getting access without cutting holes.


That way you could
clean out all the old goop... somebody is sure to have squeezed some
in from above, at some point in the past... maybe it even worked for a
while... and start fresh.

Doesn't look like there's been old goop put in from above - the gaps just
have some dirt in them.


Lately I've been using 3M 4200 UV-resistant.
Works well on everything I've rebedded so far.

Noted. How about Sikaflex? It's rather cheaper than 3M in my local chandler.


--
Wally
www.artbywally.com
www.wally.myby.co.uk

Butyl tape?
--Alan Gomes

"Wally" wrote in message
...
My boat (Foxcub 18) has some leaks in the topsides, where the shrouds come
down to the deck. The shrouds attach to U-bolts which pass through the
edge
of the deck to a blind fixing inside. After messing about with a hose, it
appears that water is getting through between the U-bolts and GRP.

Since the fixings don't seem to be removable, I'm thinking of sealing them
from above, using some sort of mastic or highly-flexible sealant, perhaps
squeezed in with a syringe. What would be a good material to use? Any
other
way of fixing the problem?


--
Wally
www.artbywally.com
www.wally.myby.co.uk