BoatBanter.com

BoatBanter.com (https://www.boatbanter.com/)
-   ASA (https://www.boatbanter.com/asa/)
-   -   Sealing topside leaks (https://www.boatbanter.com/asa/22822-sealing-topside-leaks.html)

Wally September 16th 04 11:27 AM

Sealing topside leaks
 
My boat (Foxcub 18) has some leaks in the topsides, where the shrouds come
down to the deck. The shrouds attach to U-bolts which pass through the edge
of the deck to a blind fixing inside. After messing about with a hose, it
appears that water is getting through between the U-bolts and GRP.

Since the fixings don't seem to be removable, I'm thinking of sealing them
from above, using some sort of mastic or highly-flexible sealant, perhaps
squeezed in with a syringe. What would be a good material to use? Any other
way of fixing the problem?


--
Wally
www.artbywally.com
www.wally.myby.co.uk



Bobsprit September 16th 04 11:29 AM

Since the fixings don't seem to be removable, I'm thinking of sealing them
from above, using some sort of mastic or highly-flexible sealant, perhaps


Wally, you're going to get plenty of real advise on this one, so I don't feel
there's anything wrong with me pointing out that you're a royal putz who
shouldn't be allowed to own a boat.
Non removable fixings????

Bwahahahahahahaha!

RB

Wally September 16th 04 11:44 AM

Bobsprit wrote:

Wally, you're going to get plenty of real advise on this one, so I
don't feel there's anything wrong with me pointing out that you're a
royal putz who shouldn't be allowed to own a boat.
Non removable fixings????

Bwahahahahahahaha!


Thank you for offering such unmitigated support to a sweet, innocent,
fresh-faced n00b. If I'm ever in NY, remind me to give your boatload of
waif-and-stray skanks a wide berth.


--
Wally
www.artbywally.com
www.wally.myby.co.uk




Bobsprit September 16th 04 11:51 AM

Thank you for offering such unmitigated support to a sweet, innocent,
fresh-faced n00b.

Wally, a few moments of research could produce the info you want. You might
also join a few of the Sailnet groups which could provide you with FAR more
genuine info that this group can provide.
If you want a "proper" repair, you need to rebed those U bolts, even if you
have to cut them out. It's done all the time on low-end boats. Most recently I
watched a guy do exactly that job on a small Chrysler boat. But wouldn't you
prefer more feedback from a far bigger group that this one?
Get a clue, Wally. Puh-lease!

RB

DSK September 16th 04 02:46 PM

Wally wrote:
My boat (Foxcub 18) has some leaks in the topsides, where the shrouds come
down to the deck. The shrouds attach to U-bolts which pass through the edge
of the deck to a blind fixing inside. After messing about with a hose, it
appears that water is getting through between the U-bolts and GRP.

Since the fixings don't seem to be removable, I'm thinking of sealing them
from above, using some sort of mastic or highly-flexible sealant, perhaps
squeezed in with a syringe. What would be a good material to use? Any other
way of fixing the problem?


Squeezing in miracle goop from above is doubtful. Is there any way of
taking the nuts & backing plates off the underside? That way you could
clean out all the old goop... somebody is sure to have squeezed some in
from above, at some point in the past... maybe it even worked for a
while... and start fresh. Lately I've been using 3M 4200 UV-resistant.
Works well on everything I've rebedded so far.

Fresh Breezes- Doug King


Scott Vernon September 16th 04 03:35 PM


"Bobsprit" wrote ...

Wally, I used duct tape on my boat. Stopped the leaks and looks

really cool.

BS




Alan Gomes September 17th 04 07:47 AM

Butyl tape?
--Alan Gomes

"Wally" wrote in message
...
My boat (Foxcub 18) has some leaks in the topsides, where the shrouds come
down to the deck. The shrouds attach to U-bolts which pass through the

edge
of the deck to a blind fixing inside. After messing about with a hose, it
appears that water is getting through between the U-bolts and GRP.

Since the fixings don't seem to be removable, I'm thinking of sealing them
from above, using some sort of mastic or highly-flexible sealant, perhaps
squeezed in with a syringe. What would be a good material to use? Any

other
way of fixing the problem?


--
Wally
www.artbywally.com
www.wally.myby.co.uk





Wally September 17th 04 09:33 PM

Bobsprit wrote:

Wally, you're going to get plenty of real advise on this one


And Bobsprit also wrote:

... join a few of the Sailnet groups which could provide you
with FAR more genuine info that this group can provide.


You're contradicting yourself.


If you want a "proper" repair, you need to rebed those U bolts, even
if you have to cut them out. It's done all the time on low-end boats.
Most recently I watched a guy do exactly that job on a small Chrysler
boat.


The boat has a cabin lining which is a single-piece GRP moulding. There's an
air gap between this and the hull, and I can just get my fingers into the
gap, accessed from inside the settee berth. I used a little mirror to try
and get a look, and I can just see the inside of one of the U-bolts (three
per side). I reckon the chances of getting at the nuts with a socket set are
somewhere between minimal to hopeless, so I'm going to look into the
possibility of cutting apertures in the liner to gain access that way.
There's a glued-on moulded shelf on the liner where I'd want to do the
cutting, so I need to try and get that off first.


But wouldn't you prefer more feedback from a far bigger group
that this one?


Get a clue, Wally. Puh-lease!


Lame.


--
Wally
www.artbywally.com
www.wally.myby.co.uk



Bobsprit September 17th 04 10:37 PM

The boat has a cabin lining which is a single-piece GRP moulding.


Okay, so they put in the bolts, then glued or riveted the liner in. The liner
won't come down and you can't slip a wrench in their to grab a bolt. You'd
never get a bolt back on anyway in that case. That sucks. But cutting access
areas into the liner is a good idea. A Roto Zip tool (use the depth setting)
can make this a neat job. Set the depth to JUST through the depth of the liner.
You could then make teak plugs for the holes you made later on. Be careful not
to cut right up through the deckside!
Do it slowly and plan it carefull to avoid a mishap that will leave you with a
larger repair and glass work.
Why not take pics of this job before and after. Done right, you'll have made a
nice repair and an improvement to her that will help sell her when that day
comes.

Good Luck,

RB

Wally September 17th 04 11:30 PM

Bobsprit wrote:

Okay, so they put in the bolts, then glued or riveted the liner in.


Yup, that's how it looks to me. What bugs me is that there doesn't seem to
be much of a backing plate other than the little strip that usually comes
with a standard U-bolt. That said, there's very little room to fit anything
bigger - no extra width, but maybe some more length. Whether any more
backing is needed is something I don't know - I'm not sure on what sort of
strain the rig is likely to put on the edge of the deck, or how well the GRP
will cope with it.


The liner won't come down and you can't slip a wrench in their to
grab a bolt. You'd never get a bolt back on anyway in that case. That
sucks. But cutting access areas into the liner is a good idea. A Roto
Zip tool (use the depth setting) can make this a neat job. Set the
depth to JUST through the depth of the liner.


I'm not sure that there's enough room to get in with a Rotozip - it's
possible, but it depends on where I need the hole such that the chosen tool
can reach up. The higher the hole needs to be, the harder it'll be to get
the Rotozip in (because it'll be hitting the liner/underside of the side
deck). I think a 1/4" drive socket with a short extension will work, though,
and that will let me work two or three inches below the underside.


You could then make
teak plugs for the holes you made later on.


No need to be that fancy - the holes would be behind the moulded shelf,
which would be reattached afterwards.


Be careful not to cut
right up through the deckside!
Do it slowly and plan it carefull to avoid a mishap that will leave
you with a larger repair and glass work.


Yup. No worries there.


Why not take pics of this job before and after. Done right, you'll
have made a nice repair and an improvement to her that will help sell
her when that day comes.


It's highly likely that I'll do pictures - I take loads as it is, and find
them very handy for getting a look at something when I'm at home, thinking
about stuff that I want to do.


--
Wally
www.artbywally.com
www.wally.myby.co.uk




All times are GMT +1. The time now is 04:49 PM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 BoatBanter.com