Home |
Search |
Today's Posts |
#1
posted to rec.boats
|
|||
|
|||
Can't reinstall outdrive (alpha I gen II) - First timer needs tip..
I have a 94' mercruise v8 5.7 liter w/ alpha i gen2 drive. I had to remove
it to fix a leak in the gear lube. Upon attempting to reinstall the drive I am having problems getting it all the way in. I can get it as far as the beginnings of the bolts but then it doesn't go any further.. I have the assistance of 2 other people lifting and guiding.. the shift shafts are aligned, but it doesn't seem to get to the point where the would go together. The drive is engaged in the FORWARD position.... I know there has to be a trick of the trade to do this... any help is greatly appreciated.. Thanks!! -Matt |
#2
posted to rec.boats
|
|||
|
|||
Can't reinstall outdrive (alpha I gen II) - First timer needs tip..
The gear shifter must also be in forward. Try stepping on the left side of
the prop while moving the drive into position. This will help to engage the splines. Jim "oelf92" wrote in message ... I have a 94' mercruise v8 5.7 liter w/ alpha i gen2 drive. I had to remove it to fix a leak in the gear lube. Upon attempting to reinstall the drive I am having problems getting it all the way in. I can get it as far as the beginnings of the bolts but then it doesn't go any further.. I have the assistance of 2 other people lifting and guiding.. the shift shafts are aligned, but it doesn't seem to get to the point where the would go together. The drive is engaged in the FORWARD position.... I know there has to be a trick of the trade to do this... any help is greatly appreciated.. Thanks!! -Matt |
#3
posted to rec.boats
|
|||
|
|||
Can't reinstall outdrive (alpha I gen II) - First timer needs tip..
I have the gear shifter in FORWARD, not all the way just enough to engage..
and it seems as if the splines went together. I tried to rotate the prop CCW but it wouldn't budge.. And i wasn't to the point where the shift coupler connects... How hard should i attempt to turn the prop? Should I put some weight behind it? I don't want to strip or grind anything... "JIMinFL" wrote in message . net... The gear shifter must also be in forward. Try stepping on the left side of the prop while moving the drive into position. This will help to engage the splines. Jim "oelf92" wrote in message ... I have a 94' mercruise v8 5.7 liter w/ alpha i gen2 drive. I had to remove it to fix a leak in the gear lube. Upon attempting to reinstall the drive I am having problems getting it all the way in. I can get it as far as the beginnings of the bolts but then it doesn't go any further.. I have the assistance of 2 other people lifting and guiding.. the shift shafts are aligned, but it doesn't seem to get to the point where the would go together. The drive is engaged in the FORWARD position.... I know there has to be a trick of the trade to do this... any help is greatly appreciated.. Thanks!! -Matt |
#4
posted to rec.boats
|
|||
|
|||
Can't reinstall outdrive (alpha I gen II) - First timer needs tip..
I hope you got the shifter lined up right when you put the drive halves
together.When the shift shaft on the drive is fore and aft the drive should be in forward gear. If you move the prop CCW you should see the ujoint shaft move with it. When you do this exercise with the drive off you will see how much force it takes to turn the u-joint shaft with the prop. It really doesn't take a lot. While you have the drive off you ought to check the engine alignment. Also make sure you have the o rings in the right places, and grease them along with the splines. The gimbal bearing could be cocked a little. The engine alignment tool would straighten it for you. Jim "oelf92" wrote in message t... I have the gear shifter in FORWARD, not all the way just enough to engage.. and it seems as if the splines went together. I tried to rotate the prop CCW but it wouldn't budge.. And i wasn't to the point where the shift coupler connects... How hard should i attempt to turn the prop? Should I put some weight behind it? I don't want to strip or grind anything... "JIMinFL" wrote in message . net... The gear shifter must also be in forward. Try stepping on the left side of the prop while moving the drive into position. This will help to engage the splines. Jim "oelf92" wrote in message ... I have a 94' mercruise v8 5.7 liter w/ alpha i gen2 drive. I had to remove it to fix a leak in the gear lube. Upon attempting to reinstall the drive I am having problems getting it all the way in. I can get it as far as the beginnings of the bolts but then it doesn't go any further.. I have the assistance of 2 other people lifting and guiding.. the shift shafts are aligned, but it doesn't seem to get to the point where the would go together. The drive is engaged in the FORWARD position.... I know there has to be a trick of the trade to do this... any help is greatly appreciated.. Thanks!! -Matt |
#5
posted to rec.boats
|
|||
|
|||
Can't reinstall outdrive (alpha I gen II) - First timer needs tip..
The shifter is lined up like the mercruise book shows.. how does the engine
become unaligned? I can see the ujoint shaft move if i put a little resistance on the shaft. I'll get some rest and try again in th emorning.. thanks for the help........ "JIMinFL" wrote in message nk.net... I hope you got the shifter lined up right when you put the drive halves together.When the shift shaft on the drive is fore and aft the drive should be in forward gear. If you move the prop CCW you should see the ujoint shaft move with it. When you do this exercise with the drive off you will see how much force it takes to turn the u-joint shaft with the prop. It really doesn't take a lot. While you have the drive off you ought to check the engine alignment. Also make sure you have the o rings in the right places, and grease them along with the splines. The gimbal bearing could be cocked a little. The engine alignment tool would straighten it for you. Jim "oelf92" wrote in message t... I have the gear shifter in FORWARD, not all the way just enough to engage.. and it seems as if the splines went together. I tried to rotate the prop CCW but it wouldn't budge.. And i wasn't to the point where the shift coupler connects... How hard should i attempt to turn the prop? Should I put some weight behind it? I don't want to strip or grind anything... "JIMinFL" wrote in message . net... The gear shifter must also be in forward. Try stepping on the left side of the prop while moving the drive into position. This will help to engage the splines. Jim "oelf92" wrote in message ... I have a 94' mercruise v8 5.7 liter w/ alpha i gen2 drive. I had to remove it to fix a leak in the gear lube. Upon attempting to reinstall the drive I am having problems getting it all the way in. I can get it as far as the beginnings of the bolts but then it doesn't go any further.. I have the assistance of 2 other people lifting and guiding.. the shift shafts are aligned, but it doesn't seem to get to the point where the would go together. The drive is engaged in the FORWARD position.... I know there has to be a trick of the trade to do this... any help is greatly appreciated.. Thanks!! -Matt |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Alpha One Gen. II lubrication points | General | |||
Alpha 1 outdrives | Cruising | |||
What Year 3.0l will fit my 1988 Alpha one? | General | |||
outdrive questions | Cruising | |||
Mercruiser outdrive question | General |