Home |
Search |
Today's Posts |
|
#1
posted to rec.boats.paddle
|
|||
|
|||
Kevlar canoe - minor bow repair
I've been playing 'ice breaker' a bit too enthusiastically in my Wenonah
Voyager and now there are two patches at the bow where the ice has worn through the skin coat and bits of kevlar weave are showing. Probably too small to cause a drop in hull speed, and I am pretty sure it won't affect waterproofing of the front buoyancy chamber either, but cosmetically it isn't great and I'd like to fix it and then declare my ice breaking days over once and for all. (Or maybe I need a kevlar strip at the bow to protect the, er, kevlar.) As you can probably tell I have no experience working with laminates whatsoever. Is it just a case of daubing some vinyl ester resin onto the kevlar weave, waiting for it to cure and then maybe filing the end result into shape? Which tools and materials will I need and where can small quantities be sourced from at a reasonable price? Grateful for any advice, I |
#2
posted to rec.boats.paddle
|
|||
|
|||
Kevlar canoe - minor bow repair
Call kevlar and find out the particular resin or plastic, the chemistry
part. then call complete sculptor in nyc (find # on internet) for technical info. I am a sculptor and they have a tech line. Wear gloves, and respirator when working with any of these materials. |
#3
posted to rec.boats.paddle
|
|||
|
|||
Kevlar canoe - minor bow repair
Call kevlar and find out the particular resin or plastic, the chemistry
part. then call complete sculptor in nyc (find # on internet) for technical info. I am a sculptor and they have a tech line. Wear gloves, and respirator when working with any of these materials. |
#4
posted to rec.boats.paddle
|
|||
|
|||
Kevlar canoe - minor bow repair
Check out this site: http://www.redrockstore.com/canoepatch.html
You'll probably have to substitute vinylester resin for epoxy resin in your case. |
#5
posted to rec.boats.paddle
|
|||
|
|||
Kevlar canoe - minor bow repair
Either way you may want to seal up that hole to the kevlar befor water
gets in there and freezes. That will cause expantion and more of the laminates will start to shed or flake off. Kevlar bow strips are available. I think I would get some of that stuff if you are going to immitate a Coast Guard ice breaker. I feel your pain. I used ny NDK kayak to take rock samples from a local cliff face Jan 1 and have the same work to do but a little more of it. Mine leaks..... Yuk. You know its only the likes us us that have this problem. In most circles when you talk about an ice breaker , or breaking the ice it is normally done with.... " You hair is quite beautifull, the highlights set off your eyes," sunsiquent cost a glass of wine, perhaps a bottle if things go well...... Extended cost's Three kids one headed to university next year, three , no four people wanting to take the car, and extended bunch of inlaws. ARRG!!! Oh, I have a son who likes to paddle.... Thank God! |
#6
posted to rec.boats.paddle
|
|||
|
|||
Kevlar canoe - minor bow repair
Ivan wrote:
Ivan, depending on where you live, you'll need to find the following: fiberglass cloth, 4-6oz weave. Polyester resin NOT EPOXY!!! Sandpaper - 150grit for presanding, and 200-400-600 for finish Heavy duty saran wrap. painters tape disposable paint brush ambient temp 65-75 degrees NO COLDER A little acetone might be nice too, but if the boat is clean don't bother. 1. clean damaged areas well, and dry thoroughly 2. sand damaged area lightly - but not enough to fuzz the kevlar 3. cut cloth to fit over the damage and a little more. If you've damaged the very nose end, you may need to shape and cut gussets in the material to get it to lay flat 4. mix the resin per mfg instructions. Mix a little more than you think you'll need 5. brush a very thin coat over the section to be repaired 6. carefully lay the glass into the resin, dabbing with the brush to make it lay down smoothly 7. completely wet out the glass, taking care not to let it run. work rapidly, because you've only got a few minutes before it kicks. clean up any runs or drips with a clean rag. 8. when it starts to kick (your resin cup will begin to feel warm), cover the area with the saran wrap, and smooth it carefully, making *sure* to get out any wrinkles. tape it down tight. You just saved about an hour of sanding. 9. Let it dry for an hour or so, remove the saran wrap. 10. Sand with progressively finer grit sandpaper, taking care not to sand thru to the kevlar. Go paddle your boat! Marsh www.kettercanoeing.com Wenonah Dealer/Distributor I've been playing 'ice breaker' a bit too enthusiastically in my Wenonah Voyager and now there are two patches at the bow where the ice has worn through the skin coat and bits of kevlar weave are showing. Probably too small to cause a drop in hull speed, and I am pretty sure it won't affect waterproofing of the front buoyancy chamber either, but cosmetically it isn't great and I'd like to fix it and then declare my ice breaking days over once and for all. (Or maybe I need a kevlar strip at the bow to protect the, er, kevlar.) As you can probably tell I have no experience working with laminates whatsoever. Is it just a case of daubing some vinyl ester resin onto the kevlar weave, waiting for it to cure and then maybe filing the end result into shape? Which tools and materials will I need and where can small quantities be sourced from at a reasonable price? Grateful for any advice, I |
#7
posted to rec.boats.paddle
|
|||
|
|||
Kevlar canoe - minor bow repair
"Marsh Jones" wrote in message . .. Ivan wrote: Marsh, Good directions for the bow repair!! Also if you cut the fiberglass patch on the bias it fits the bow curves a bit better. Mike |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
rec.boats.paddle sea kayaking FAQ | General | |||
Canoe Chairs | General | |||
rec.boats.paddle sea kayaking FAQ | General | |||
rec.boats.paddle sea kayaking FAQ | General | |||
rec.boats.paddle sea kayaking FAQ | General |