Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
r_d
 
Posts: n/a
Default Freeing a seized OMC... (2nd post attempt)

Hi All,
I am trying to get my boat running. The engine has been sitting for two
years when it was stored (oil in the cylinders and antifreeze in the block).
The engine does not spin with the starter, what is the process to get it
spinning? I pulled out the plugs and they were clean (no rust), the oil in
the engine is clean (no water) and it smells fine. My uncle says to just
put a breaker bar on the balancer and rock it back in forth until it spins.
Is this ok, it seams to me that would be very hard on the bearings? The
engine is an OMC stern drive 260 (1986 Chevy 350).

Thanks for the advice.

mark

P.S. This is a second post with the same message. My news server ate the
first one, if you received two copies this is why. thanks



  #2   Report Post  
Franko
 
Posts: n/a
Default

I know a couple of folks who work on rust-fused engines routinely: if the
mystery oil doesn't work (should free up the rings-to-cylinder-wall fusing),
they fill the crankcase with oil all the way up to the head (in case there
are bottom end fusings), let it sit for a week, then use the breaker bar
again. Good luck.

"JIMinFL" wrote in message
link.net...
Your uncles advice is OK. Just don't over do it. Before you blame the

engine
you need to remove the stern drive and/or the starter. (starter is easier

to
remove,usually.) If you still cant get the engine to roll over, fill the
cylinders with mystery oil and wait anywhere from a day to a week and try
again.
JIMinFL

[snip]

"r_d" wrote in message
groups.com...
Hi All,
I am trying to get my boat running. The engine has been sitting for two
years when it was stored (oil in the cylinders and antifreeze in the

block).
The engine does not spin with the starter, what is the process to get it
spinning? I pulled out the plugs and they were clean (no rust), the oil

in
the engine is clean (no water) and it smells fine. My uncle says to just
put a breaker bar on the balancer and rock it back in forth until it

spins.
Is this ok, it seams to me that would be very hard on the bearings? The
engine is an OMC stern drive 260 (1986 Chevy 350).

Thanks for the advice.

mark

P.S. This is a second post with the same message. My news server ate the
first one, if you received two copies this is why. thanks





Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is Off
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Want money for a new boat [email protected] General 3 March 27th 05 04:19 PM
Want spare money for cruising [email protected] Cruising 1 March 27th 05 02:00 AM
I've seen a post or two Capt. Neal® ASA 2 December 19th 04 03:38 AM
Enjoy the wild places while they last riverman General 252 November 30th 04 10:22 PM
OT--Not again! More Chinese money buying our politicians. NOYB General 23 February 6th 04 04:01 PM


All times are GMT +1. The time now is 07:25 AM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 BoatBanter.com.
The comments are property of their posters.
 

About Us

"It's about Boats"

 

Copyright © 2017