On Sun, 13 Mar 2011 10:14:28 -0400, Gene
wrote:

So, Does anybody sell wiring harnesses with marine tinned wire or
should I simply make my own?

Just make your own with quality wire and adhesive shrink fit
connectors. Silicone grease is your friend.....

Do you put silicone grease directly on the wire before making the
crimp?

On Sun, 13 Mar 2011 10:25:00 -0400, Wayne.B
wrote:

On Sun, 13 Mar 2011 10:14:28 -0400, Gene
wrote:

So, Does anybody sell wiring harnesses with marine tinned wire or
should I simply make my own?

Just make your own with quality wire and adhesive shrink fit
connectors. Silicone grease is your friend.....

Do you put silicone grease directly on the wire before making the
crimp?

I think he was talking about the wire pull?

On Sun, 13 Mar 2011 14:31:33 -0400, Gene
wrote:

On Sun, 13 Mar 2011 09:33:23 -0700, jps wrote:

On Sun, 13 Mar 2011 10:25:00 -0400, Wayne.B
wrote:

On Sun, 13 Mar 2011 10:14:28 -0400, Gene
wrote:

So, Does anybody sell wiring harnesses with marine tinned wire or
should I simply make my own?

Just make your own with quality wire and adhesive shrink fit
connectors. Silicone grease is your friend.....

Do you put silicone grease directly on the wire before making the
crimp?

I think he was talking about the wire pull?

Most wire pulls don't involve passing it through conduit.... but if
that is the case, use a proper wire pulling lubricant....

So, what are you using the silicone grease for? Are you talking about
a conductive silicone grease?

On Sun, 13 Mar 2011 14:48:51 -0400, Gene
wrote:

On Sun, 13 Mar 2011 11:35:05 -0700, jps wrote:

On Sun, 13 Mar 2011 14:31:33 -0400, Gene
wrote:

On Sun, 13 Mar 2011 09:33:23 -0700, jps wrote:

On Sun, 13 Mar 2011 10:25:00 -0400, Wayne.B
wrote:

On Sun, 13 Mar 2011 10:14:28 -0400, Gene
wrote:

So, Does anybody sell wiring harnesses with marine tinned wire or
should I simply make my own?

Just make your own with quality wire and adhesive shrink fit
connectors. Silicone grease is your friend.....

Do you put silicone grease directly on the wire before making the
crimp?

I think he was talking about the wire pull?

Most wire pulls don't involve passing it through conduit.... but if
that is the case, use a proper wire pulling lubricant....

So, what are you using the silicone grease for? Are you talking about
a conductive silicone grease?

Silicone grease is, by definition, NOT conductive.... it is a good
thermal conductor and will help keep moisture out of electrical
junctions....

So, you're applying it around the junction as a moisture barrier, not
in it, correct?

On Mon, 14 Mar 2011 01:40:33 -0400, wrote:

On Sun, 13 Mar 2011 13:32:41 -0700, jps wrote:

On Sun, 13 Mar 2011 14:48:51 -0400, Gene
wrote:

On Sun, 13 Mar 2011 11:35:05 -0700, jps wrote:

On Sun, 13 Mar 2011 14:31:33 -0400, Gene
wrote:

On Sun, 13 Mar 2011 09:33:23 -0700, jps wrote:

On Sun, 13 Mar 2011 10:25:00 -0400, Wayne.B
wrote:

On Sun, 13 Mar 2011 10:14:28 -0400, Gene
wrote:

So, Does anybody sell wiring harnesses with marine tinned wire or
should I simply make my own?

Just make your own with quality wire and adhesive shrink fit
connectors. Silicone grease is your friend.....

Do you put silicone grease directly on the wire before making the
crimp?

I think he was talking about the wire pull?

Most wire pulls don't involve passing it through conduit.... but if
that is the case, use a proper wire pulling lubricant....

So, what are you using the silicone grease for? Are you talking about
a conductive silicone grease?

Silicone grease is, by definition, NOT conductive.... it is a good
thermal conductor and will help keep moisture out of electrical
junctions....

So, you're applying it around the junction as a moisture barrier, not
in it, correct?

It is pretty common to have the silicone gel right in the connector
with underground splices. The mechanical pressure will squeeze it out
of the actual joint but leave the rest of the connector flooded with
silicone.

That's cool. With all the weather we get here, I think it's a good
idea for all crimps. I use silicone grease on the seals of my car top
to keep it from squeeking and have used it to reassemble ceramic
faucet parts. Good stuff.

On Mon, 14 Mar 2011 12:30:31 -0400, wrote:

On Mon, 14 Mar 2011 01:35:06 -0700, jps wrote:

On Mon, 14 Mar 2011 01:40:33 -0400, wrote:

On Sun, 13 Mar 2011 13:32:41 -0700, jps wrote:

On Sun, 13 Mar 2011 14:48:51 -0400, Gene
wrote:

On Sun, 13 Mar 2011 11:35:05 -0700, jps wrote:

On Sun, 13 Mar 2011 14:31:33 -0400, Gene
wrote:

On Sun, 13 Mar 2011 09:33:23 -0700, jps wrote:

On Sun, 13 Mar 2011 10:25:00 -0400, Wayne.B
wrote:

On Sun, 13 Mar 2011 10:14:28 -0400, Gene
wrote:

So, Does anybody sell wiring harnesses with marine tinned wire or
should I simply make my own?

Just make your own with quality wire and adhesive shrink fit
connectors. Silicone grease is your friend.....

Do you put silicone grease directly on the wire before making the
crimp?

I think he was talking about the wire pull?

Most wire pulls don't involve passing it through conduit.... but if
that is the case, use a proper wire pulling lubricant....

So, what are you using the silicone grease for? Are you talking about
a conductive silicone grease?

Silicone grease is, by definition, NOT conductive.... it is a good
thermal conductor and will help keep moisture out of electrical
junctions....

So, you're applying it around the junction as a moisture barrier, not
in it, correct?

It is pretty common to have the silicone gel right in the connector
with underground splices. The mechanical pressure will squeeze it out
of the actual joint but leave the rest of the connector flooded with
silicone.

That's cool. With all the weather we get here, I think it's a good
idea for all crimps. I use silicone grease on the seals of my car top
to keep it from squeeking and have used it to reassemble ceramic
faucet parts. Good stuff.

The Dow 111 silicone works pretty good for sealing electrical stuff
(similar to spark plug boot grease) but it is sold as a plumbing lube.

I also use it to seal up PVC pipe joints that I want to be able to get
apart. As long as you have fairly low pressure (drains and swimming
pool supply pipes) it will hold. I use it for switching the 2" pipe
back and forth between the grand kid's pool sliding board and the
waterfall.

I've only been able to find it in small quantities in the plumbing
section at the big box hardware store. Have you seen it offered
retail (or wholesale) in larger quantities? Is this an electrical
warehouse item?

On Mon, 14 Mar 2011 09:44:52 -0700, jps wrote:

On Mon, 14 Mar 2011 12:30:31 -0400, wrote:

On Mon, 14 Mar 2011 01:35:06 -0700, jps wrote:

On Mon, 14 Mar 2011 01:40:33 -0400, wrote:

On Sun, 13 Mar 2011 13:32:41 -0700, jps wrote:

On Sun, 13 Mar 2011 14:48:51 -0400, Gene
wrote:

On Sun, 13 Mar 2011 11:35:05 -0700, jps wrote:

On Sun, 13 Mar 2011 14:31:33 -0400, Gene
wrote:

On Sun, 13 Mar 2011 09:33:23 -0700, jps wrote:

On Sun, 13 Mar 2011 10:25:00 -0400, Wayne.B
wrote:

On Sun, 13 Mar 2011 10:14:28 -0400, Gene
wrote:

So, Does anybody sell wiring harnesses with marine tinned wire or
should I simply make my own?

Just make your own with quality wire and adhesive shrink fit
connectors. Silicone grease is your friend.....

Do you put silicone grease directly on the wire before making the
crimp?

I think he was talking about the wire pull?

Most wire pulls don't involve passing it through conduit.... but if
that is the case, use a proper wire pulling lubricant....

So, what are you using the silicone grease for? Are you talking about
a conductive silicone grease?

Silicone grease is, by definition, NOT conductive.... it is a good
thermal conductor and will help keep moisture out of electrical
junctions....

So, you're applying it around the junction as a moisture barrier, not
in it, correct?

It is pretty common to have the silicone gel right in the connector
with underground splices. The mechanical pressure will squeeze it out
of the actual joint but leave the rest of the connector flooded with
silicone.

That's cool. With all the weather we get here, I think it's a good
idea for all crimps. I use silicone grease on the seals of my car top
to keep it from squeeking and have used it to reassemble ceramic
faucet parts. Good stuff.

The Dow 111 silicone works pretty good for sealing electrical stuff
(similar to spark plug boot grease) but it is sold as a plumbing lube.

I also use it to seal up PVC pipe joints that I want to be able to get
apart. As long as you have fairly low pressure (drains and swimming
pool supply pipes) it will hold. I use it for switching the 2" pipe
back and forth between the grand kid's pool sliding board and the
waterfall.

I've only been able to find it in small quantities in the plumbing
section at the big box hardware store. Have you seen it offered
retail (or wholesale) in larger quantities? Is this an electrical
warehouse item?

Did a google search and found lots under Dow 111 but still only in 5.3
oz tubes. I'm looking for the tub size that'll last for years.

On Mon, 14 Mar 2011 01:40:33 -0400, wrote:

It is pretty common to have the silicone gel right in the connector
with underground splices. The mechanical pressure will squeeze it out
of the actual joint but leave the rest of the connector flooded with
silicone.

It is also useful for prelubricating new water pump impellers, a trick
learned from my diesel mechanic. It helps with insertion and also
prevents dry start wear and tear.

On 3/14/2011 10:23 AM, Wayne.B wrote:
On Mon, 14 Mar 2011 01:40:33 -0400, wrote:

It is pretty common to have the silicone gel right in the connector
with underground splices. The mechanical pressure will squeeze it out
of the actual joint but leave the rest of the connector flooded with
silicone.

It is also useful for prelubricating new water pump impellers, a trick
learned from my diesel mechanic. It helps with insertion and also
prevents dry start wear and tear.


Apply the dielectric grease after making the mechanical connection to
insure getting a good connection.

In article , says...

On 3/14/2011 10:23 AM, Wayne.B wrote:
On Mon, 14 Mar 2011 01:40:33 -0400, wrote:

It is pretty common to have the silicone gel right in the connector
with underground splices. The mechanical pressure will squeeze it out
of the actual joint but leave the rest of the connector flooded with
silicone.

It is also useful for prelubricating new water pump impellers, a trick
learned from my diesel mechanic. It helps with insertion and also
prevents dry start wear and tear.


Apply the dielectric grease after making the mechanical connection to
insure getting a good connection.

Has anybody tried any of that liquid electrical tape? I just noticed a
bottle in my electrical box the other day. It seems it could be a real
mess in tight places, but not as bad as trying to wrap tape in close
areas.