On Apr 17, 8:22*am, John H wrote:
On Fri, 16 Apr 2010 21:47:36 -0400, Larry wrote:
John H wrote:
On Fri, 16 Apr 2010 15:39:53 -0700 (PDT), *wrote:

On Apr 16, 4:18 pm, John *wrote:

It is my belief that bungee cords should not be used with boat covers, unless
the boat cover is of the 'throwaway' variety.

Bungee cords stretch, and they will often allow the cover to sag a little when
it begins raining or snow. Once the cover sags just a bit, the weight of more
water or snow will cause it to sag even more. The bungee cord is helping this
process because it is stretching to accomodate the extra weight.

When I got my new cover, I followed the maker's advice and bought a tie down kit
to go with it. The kit is only $22.59 *Amazon.

http://www.amazon.com/Carver-Boat-Co.../dp/B0000AYI62

"Constructed Of 1" Black Polypropylene Webbing And Convenient Quick Release
Buckles."

The kits contain 12 straps, each 8' long.

The final product looks like this:

http://i98.photobucket.com/albums/l2...atCover001.jpg

http://i98.photobucket.com/albums/l2...atCover002.jpg
--
John H

For a great time, go here first...http://tinyurl.com/ygqxs5v

When I first got my 18'r four years ago, I parked it outside and took
a 10 ft sheet of plywood, *and set it on the lip of the windshield and
the back of the i/o engine cover, then put a large cheap, silver , non-
UV collecting tarp over it and used a handful of black rubber straps
to hold it in place from the eye holes to the trailer frame. , nothing
of extreme tightness, and the board did a good job of covering with no
snow/rain/ice building up because there were no pockets being formed.
In the spring, I hosed off the tarp, let it dry, unhooked everything,
folded it up and all was good. The tarp was loose enough that it
wouldn't catch a sharp corner and rip, yet it *let plenty of
ventilation flow through the boat, and was firm enough to stay in
place. and not blow away.

No, I am *not* going to cover my boat with a 10' sheet of plywood and a tarp.
Hell, I'd get laughed out of my marina!
--
John H

For a great time, go here first...http://tinyurl.com/ygqxs5v

10' plywood? *I've never seen it for sale!

Knowing Tim, I'll bet he scabbed a few smaller pieces together!
--
John H

For a great time, go here first...http://tinyurl.com/ygqxs5v- Hide quoted text -

- Show quoted text -

No, actually my dad came across some 10 ft. pieces several years ago
at an auction that were left over from a special order construction
project. I've never seen them that long at a lumber yard before. I
dont' know what they were used for but I have about 6 or 7 sheets of
the stuff.

On Sat, 17 Apr 2010 08:47:15 -0700 (PDT), Tim wrote:

On Apr 17, 8:22*am, John H wrote:
On Fri, 16 Apr 2010 21:47:36 -0400, Larry wrote:
John H wrote:
On Fri, 16 Apr 2010 15:39:53 -0700 (PDT), *wrote:

On Apr 16, 4:18 pm, John *wrote:

It is my belief that bungee cords should not be used with boat covers, unless
the boat cover is of the 'throwaway' variety.

Bungee cords stretch, and they will often allow the cover to sag a little when
it begins raining or snow. Once the cover sags just a bit, the weight of more
water or snow will cause it to sag even more. The bungee cord is helping this
process because it is stretching to accomodate the extra weight.

When I got my new cover, I followed the maker's advice and bought a tie down kit
to go with it. The kit is only $22.59 *Amazon.

http://www.amazon.com/Carver-Boat-Co.../dp/B0000AYI62

"Constructed Of 1" Black Polypropylene Webbing And Convenient Quick Release
Buckles."

The kits contain 12 straps, each 8' long.

The final product looks like this:

http://i98.photobucket.com/albums/l2...atCover001.jpg

http://i98.photobucket.com/albums/l2...atCover002.jpg
--
John H

For a great time, go here first...http://tinyurl.com/ygqxs5v

When I first got my 18'r four years ago, I parked it outside and took
a 10 ft sheet of plywood, *and set it on the lip of the windshield and
the back of the i/o engine cover, then put a large cheap, silver , non-
UV collecting tarp over it and used a handful of black rubber straps
to hold it in place from the eye holes to the trailer frame. , nothing
of extreme tightness, and the board did a good job of covering with no
snow/rain/ice building up because there were no pockets being formed.
In the spring, I hosed off the tarp, let it dry, unhooked everything,
folded it up and all was good. The tarp was loose enough that it
wouldn't catch a sharp corner and rip, yet it *let plenty of
ventilation flow through the boat, and was firm enough to stay in
place. and not blow away.

No, I am *not* going to cover my boat with a 10' sheet of plywood and a tarp.
Hell, I'd get laughed out of my marina!
--
John H

For a great time, go here first...http://tinyurl.com/ygqxs5v

10' plywood? *I've never seen it for sale!

Knowing Tim, I'll bet he scabbed a few smaller pieces together!
--
John H

For a great time, go here first...http://tinyurl.com/ygqxs5v- Hide quoted text -

- Show quoted text -

No, actually my dad came across some 10 ft. pieces several years ago
at an auction that were left over from a special order construction
project. I've never seen them that long at a lumber yard before. I
dont' know what they were used for but I have about 6 or 7 sheets of
the stuff.

Probably collectors' items Tim. Hell, they may be worth a fortune.
--
John H

For a great time, go here first... http://tinyurl.com/ygqxs5v

On Apr 17, 7:10*pm, John H wrote:
On Sat, 17 Apr 2010 08:47:15 -0700 (PDT), Tim wrote:
On Apr 17, 8:22*am, John H wrote:
On Fri, 16 Apr 2010 21:47:36 -0400, Larry wrote:
John H wrote:
On Fri, 16 Apr 2010 15:39:53 -0700 (PDT), *wrote:

On Apr 16, 4:18 pm, John *wrote:

It is my belief that bungee cords should not be used with boat covers, unless
the boat cover is of the 'throwaway' variety.

Bungee cords stretch, and they will often allow the cover to sag a little when
it begins raining or snow. Once the cover sags just a bit, the weight of more
water or snow will cause it to sag even more. The bungee cord is helping this
process because it is stretching to accomodate the extra weight.

When I got my new cover, I followed the maker's advice and bought a tie down kit
to go with it. The kit is only $22.59 *Amazon.

http://www.amazon.com/Carver-Boat-Co.../dp/B0000AYI62

"Constructed Of 1" Black Polypropylene Webbing And Convenient Quick Release
Buckles."

The kits contain 12 straps, each 8' long.

The final product looks like this:

http://i98.photobucket.com/albums/l2...atCover001.jpg

http://i98.photobucket.com/albums/l2...atCover002.jpg
--
John H

For a great time, go here first...http://tinyurl.com/ygqxs5v

When I first got my 18'r four years ago, I parked it outside and took
a 10 ft sheet of plywood, *and set it on the lip of the windshield and
the back of the i/o engine cover, then put a large cheap, silver , non-
UV collecting tarp over it and used a handful of black rubber straps
to hold it in place from the eye holes to the trailer frame. , nothing
of extreme tightness, and the board did a good job of covering with no
snow/rain/ice building up because there were no pockets being formed.
In the spring, I hosed off the tarp, let it dry, unhooked everything,
folded it up and all was good. The tarp was loose enough that it
wouldn't catch a sharp corner and rip, yet it *let plenty of
ventilation flow through the boat, and was firm enough to stay in
place. and not blow away.

No, I am *not* going to cover my boat with a 10' sheet of plywood and a tarp.
Hell, I'd get laughed out of my marina!
--
John H

For a great time, go here first...http://tinyurl.com/ygqxs5v

10' plywood? *I've never seen it for sale!

Knowing Tim, I'll bet he scabbed a few smaller pieces together!
--
John H

For a great time, go here first...http://tinyurl.com/ygqxs5v-Hide quoted text -

- Show quoted text -

No, actually my dad came across some 10 ft. pieces several years ago
at an auction that were left over from a special order *construction
project. I've never seen them that long at a lumber yard before. I
dont' know what they were used for but I have about 6 or 7 sheets of
the stuff.

Probably collectors' items Tim. Hell, they may be worth a fortune.
--
John H

For a great time, go here first...http://tinyurl.com/ygqxs5v

"collector grade" plywood. Come to think of it, there probably is
sucha thing.

who'd a thunk it?

wrote in message
...
On Sat, 17 Apr 2010 17:32:00 -0700 (PDT), Tim
wrote:

at an auction that were left over from a special order construction
project. I've never seen them that long at a lumber yard before. I
dont' know what they were used for but I have about 6 or 7 sheets of
the stuff.

Probably collectors' items Tim. Hell, they may be worth a fortune.
--
John H

For a great time, go here first...http://tinyurl.com/ygqxs5v

"collector grade" plywood. Come to think of it, there probably is
sucha thing.

who'd a thunk it?

Any real lumber yard should be able to order it for you. You can also
get 5' wide plywood.
They may want you to buy a bundle of it tho ;-)

Nope, they would want you to buy a "unit" of it. I have never seen the 5x
but 4x10 is a catalog item. Probably for use like 4x10 sheetrock sheathing.

"Bill McKee" wrote in message
...

wrote in message
...
On Sat, 17 Apr 2010 17:32:00 -0700 (PDT), Tim
wrote:

at an auction that were left over from a special order construction
project. I've never seen them that long at a lumber yard before. I
dont' know what they were used for but I have about 6 or 7 sheets of
the stuff.

Probably collectors' items Tim. Hell, they may be worth a fortune.
--
John H

For a great time, go here first...http://tinyurl.com/ygqxs5v

"collector grade" plywood. Come to think of it, there probably is
sucha thing.

who'd a thunk it?

Any real lumber yard should be able to order it for you. You can also
get 5' wide plywood.
They may want you to buy a bundle of it tho ;-)

Nope, they would want you to buy a "unit" of it. I have never seen the 5x
but 4x10 is a catalog item. Probably for use like 4x10 sheetrock
sheathing.

It's mainly used for shear walls when the ceiling height is greater than 8'.
It saves a bunch of labor since you don't have to block and nail off the
shorter ply.

--Mike

On 4/20/10 11:45 AM, wrote:
On Mon, 19 Apr 2010 22:45:31 -0700, wrote:



"Bill wrote in message
...

wrote in message
...
On Sat, 17 Apr 2010 17:32:00 -0700 (PDT),
wrote:

at an auction that were left over from a special order construction
project. I've never seen them that long at a lumber yard before. I
dont' know what they were used for but I have about 6 or 7 sheets of
the stuff.

Probably collectors' items Tim. Hell, they may be worth a fortune.
--
John H

For a great time, go here first...http://tinyurl.com/ygqxs5v

"collector grade" plywood. Come to think of it, there probably is
sucha thing.

who'd a thunk it?

Any real lumber yard should be able to order it for you. You can also
get 5' wide plywood.
They may want you to buy a bundle of it tho ;-)

Nope, they would want you to buy a "unit" of it. I have never seen the 5x
but 4x10 is a catalog item. Probably for use like 4x10 sheetrock
sheathing.

It's mainly used for shear walls when the ceiling height is greater than 8'.
It saves a bunch of labor since you don't have to block and nail off the
shorter ply.

--Mike

That's why I know about it. The houses my wife used to build all had
10' ceilings and 8' doors. I used to joke that we must be expecting an
influx of NBA players here.


4x10 ply would make an interesting base for a slot car racing track,
assuming there is still interest in home-based slot car racing...



--
The Tea Party's teabaggers are just the Republican base by another name.

On Sat, 17 Apr 2010 20:57:18 -0400, wrote:

Any real lumber yard should be able to order it for you. You can also
get 5' wide plywood.
They may want you to buy a bundle of it tho ;-)

Or if you hang out on the boat builder sites you can learn how to
scarf it together with epoxy to make any size sheet you want.