Home |
Search |
Today's Posts |
|
#1
posted to rec.boats.electronics
|
|||
|
|||
WiFi Access
Glen,
You make a good point about being able to scan for access points. I think the bridge comes with software for scanning, but a USB adapter would make that very easy. It would also make for a simpler setup until I decide to add a router. Any recommendations for an external antenna? Thanks, Rusty "Glenn Ashmore" wrote in message news:vUsrg.115916$Ce1.69258@dukeread01... You might try a EUB-362(EXT) high power (200mw) USB wireless adapter with an 8.5db marine antenna on the Shuttle, hard wire in the other PCs through a workgroup switch and use the Windows ICS facility to share the connection. The EUB-362 is especially attractive because you can run the USB cable up to 15' and locate the EUB362 close to the antenna. With a powered hub at the end of the USB cable you can go another 15' and take the load off the Shuttle all together.. At 2.4Ghz LMR200 coax will loose more than 50% of the signal over 20' but only 15% over the 4' that comes with the antenna. Also working off the USB port the Shuttle will own the adapter so you can scan for access points and control which one it connects to using the standard wifi utilities. You can't do that very easily with a wireless router. To give you an idea of the performance, using a 200mw Senao card connected through 16' of LMR100 an 8.5db antenna I could get a usable signal from the 500mw BVI Marine Wifi access points out to about 900 yards. The thin LMR100 lost 75% of the signal so a shorter length of LMR200 should get you out to 1,500 yards or better. -- Glenn Ashmore I'm building a 45' cutter in strip/composite. Watch my progress (or lack there of) at: http://www.rutuonline.com Shameless Commercial Division: http://www.spade-anchor-us.com |
#2
posted to rec.boats.electronics
|
|||
|
|||
WiFi Access
You might consider this whole kit from Netgate:
http://www.netgate.com/product_info.php?products_id=328 It comes with the EUB-362(EXT), an 8.5db marine antenna with mount and a 20' LMR200 cable. The antenna is pretty well built but it comes with a deck mount rather than a rail mount and will not fit some rail mounts. There is a guy on eBay with a store called "War Driving World" selling 9db marine antennas. They are a little more expensive but you have a choice of deck or rail mounts Depending on how you want to mount the EUB-362 I would ask for a shorter cable to minimize loss. I am running USB to right under the antenna and just using the cable that comes with the antenna to get the least possible loss. Both antennas and the 362 have RP-SMA jacks so you have to use a male to male RP-SMA gender changer to connect then directly. (about $5 on ebay) -- Glenn Ashmore I'm building a 45' cutter in strip/composite. Watch my progress (or lack there of) at: http://www.rutuonline.com Shameless Commercial Division: http://www.spade-anchor-us.com "Rusty" wrote in message ... Glen, You make a good point about being able to scan for access points. I think the bridge comes with software for scanning, but a USB adapter would make that very easy. It would also make for a simpler setup until I decide to add a router. Any recommendations for an external antenna? Thanks, Rusty "Glenn Ashmore" wrote in message news:vUsrg.115916$Ce1.69258@dukeread01... You might try a EUB-362(EXT) high power (200mw) USB wireless adapter with an 8.5db marine antenna on the Shuttle, hard wire in the other PCs through a workgroup switch and use the Windows ICS facility to share the connection. The EUB-362 is especially attractive because you can run the USB cable up to 15' and locate the EUB362 close to the antenna. With a powered hub at the end of the USB cable you can go another 15' and take the load off the Shuttle all together.. At 2.4Ghz LMR200 coax will loose more than 50% of the signal over 20' but only 15% over the 4' that comes with the antenna. Also working off the USB port the Shuttle will own the adapter so you can scan for access points and control which one it connects to using the standard wifi utilities. You can't do that very easily with a wireless router. To give you an idea of the performance, using a 200mw Senao card connected through 16' of LMR100 an 8.5db antenna I could get a usable signal from the 500mw BVI Marine Wifi access points out to about 900 yards. The thin LMR100 lost 75% of the signal so a shorter length of LMR200 should get you out to 1,500 yards or better. -- Glenn Ashmore I'm building a 45' cutter in strip/composite. Watch my progress (or lack there of) at: http://www.rutuonline.com Shameless Commercial Division: http://www.spade-anchor-us.com |
#3
posted to rec.boats.electronics
|
|||
|
|||
WiFi Access
"Rusty" wrote in
: You make a good point about being able to scan for access points. I think the bridge comes with software for scanning, but a USB adapter would make that very easy. It would also make for a simpler setup until I decide to add a router. NetStumbler free from http://www.stumbler.net/ Connect your GPS to the computer and NetStumbler will log GPS position where it finds each wifi point, automatically, then will interface with Google Maps and Google Earth to draw you a Wifi map of any place on the planet....(c; Did I mention Free?? |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Improved WiFi Reception for your Vessel | Cruising | |||
( OT ) "Jeff Gannon's" incredible access | General |