Home |
Search |
Today's Posts |
#21
|
|||
|
|||
Refrigerator Fan
Dick Locke wrote in message . ..
On 21 Feb 2004 06:28:15 -0800, (Richard Kollmann) wrote: "Rick & Linda Bernard" wrote in message ... Anyone use a small fan in their fridge to help stabilize the temperatures. I have seen a battery powered one. Any comment on their effectiveness. Installation of a small fan to tumble the air around the inside of the refrigerator box can greatly improve the efficiency of your refrigerator, for details on fan and installation; see FAQ #30 on my web site. http://www.kollmann-marine.com I have been thinking about doing that but have been putting it off due to concerns about drilling a hole through the foam insulation to get the wires in. Any words of wisdom on an easy way to do it? The easiest way to run the small fan wires through the box wall is to use the same hole that the refrigeration tubing runs through. Use a blunt tool to open up a small hole adjacent to the existing tubing, be careful not to scratch the tubing or vacuum panel insulation if so equipped. Do not drill holes through box or insulation if the box has vacuum panels insulation. If, it is not possible to follow the existing tubing select an area inside and outside the box, free of other tubing and electrical, that is convenient with good access. Then using a 1/8 inch drill-bit, drill a hole through the box's liner and insulation. Normally a standard drill will not be long enough but it will start the access hole. If you do not have a long drill-bit to complete the hole cut a straight section of a wire coat hanger with wire cutters. The sharp end left by the wire cutters will act as a cutting edge to complete the hole even if there is a wood bulkhead to cut through. Once the 1/8 in. pilot hole is open at both ends, a drill slightly larger than the wires can be used to increase the hole size. Silicone sealant can be used to fill and seal the hole after the wire is installed. When refrigerator or iceboxes are to be constructed I always recommend that the builder consider installing an access tube through the insulation for future wires. There are several reasons you might want or need a small fan in a refrigerator to: Tumble the air when there is insufficient natural air movement. Achieve a forced air spillover dual temperature box with a separate thermostat. Lower the temperature of a shelf located above the evaporator cooling coil or to move the warm air in a long shallow box to the evaporator. Increase the overall efficiency of an incorrectly sized evaporator by changing part of it from a static to a forced air heat exchange. From the author of books on boat refrigeration http://www.kollmann-marine.com |
#23
|
|||
|
|||
Refrigerator Fan
On 23 Feb 2004 08:04:52 -0800, (Richard
Kollmann) wrote: The easiest way to run the small fan wires through the box wall is to use the same hole that the refrigeration tubing runs through. Use a blunt tool to open up a small hole adjacent to the existing tubing, be careful not to scratch the tubing or vacuum panel insulation if so equipped. Do not drill holes through box or insulation if the box has vacuum panels insulation. If, it is not possible to follow the existing tubing select an area inside and outside the box, free of other tubing and electrical, that is convenient with good access. Then using a 1/8 inch drill-bit, drill a hole through the box's liner and insulation. Normally a standard drill will not be long enough but it will start the access hole. If you do not have a long drill-bit to complete the hole cut a straight section of a wire coat hanger with wire cutters. The sharp end left by the wire cutters will act as a cutting edge to complete the hole even if there is a wood bulkhead to cut through. Once the 1/8 in. pilot hole is open at both ends, a drill slightly larger than the wires can be used to increase the hole size. Silicone sealant can be used to fill and seal the hole after the wire is installed. Thanks, that's very helpful. I've also got a drain hole in the bottom that I think is the most accesible place. The refrig lines are a bit hard to get to. Looking at it, I also found that the drain line goes into the bilge. Arrgh. I guess I'm looking at installing a foot pump to pump into the galley sink or its drain. When refrigerator or iceboxes are to be constructed I always recommend that the builder consider installing an access tube through the insulation for future wires. There are several reasons you might want or need a small fan in a refrigerator to: Tumble the air when there is insufficient natural air movement. Achieve a forced air spillover dual temperature box with a separate thermostat. Lower the temperature of a shelf located above the evaporator cooling coil or to move the warm air in a long shallow box to the evaporator. Increase the overall efficiency of an incorrectly sized evaporator by changing part of it from a static to a forced air heat exchange. From the author of books on boat refrigeration http://www.kollmann-marine.com |
#24
|
|||
|
|||
Refrigerator Fan
My cold plate system uses a little 3" box fan to move cold air from the
freezer side to the fridge side. You can pick one up for about $3 at any electronics place. -- Keith __ Gossip is when you hear something you like about someone you don't. "LaBomba182" wrote in message ... Subject: Refrigerator Fan From: "Rick & Linda Bernard" Anyone use a small fan in their fridge to help stabilize the temperatures. Yes. I have seen a battery powered one. Any comment on their effectiveness. They work. But I would use a 12v hard wired one. Capt. Bill |
#25
|
|||
|
|||
Refrigerator Fan
My cold plate system uses a little 3" box fan to move cold air from the
freezer side to the fridge side. You can pick one up for about $3 at any electronics place. -- Keith __ Gossip is when you hear something you like about someone you don't. "LaBomba182" wrote in message ... Subject: Refrigerator Fan From: "Rick & Linda Bernard" Anyone use a small fan in their fridge to help stabilize the temperatures. Yes. I have seen a battery powered one. Any comment on their effectiveness. They work. But I would use a 12v hard wired one. Capt. Bill |
#26
|
|||
|
|||
Refrigerator Fan
You can use such tiny wire, that you should be able to just run it through
the seal of the door, if you don't mind the looks. -- Keith __ My mind works like lightning. One brilliant flash, and it's gone. "Dick Locke" wrote in message ... On 21 Feb 2004 06:28:15 -0800, (Richard Kollmann) wrote: "Rick & Linda Bernard" wrote in message ... Anyone use a small fan in their fridge to help stabilize the temperatures. I have seen a battery powered one. Any comment on their effectiveness. Installation of a small fan to tumble the air around the inside of the refrigerator box can greatly improve the efficiency of your refrigerator, for details on fan and installation; see FAQ #30 on my web site. http://www.kollmann-marine.com I have been thinking about doing that but have been putting it off due to concerns about drilling a hole through the foam insulation to get the wires in. Any words of wisdom on an easy way to do it? |
#27
|
|||
|
|||
Refrigerator Fan
You can use such tiny wire, that you should be able to just run it through
the seal of the door, if you don't mind the looks. -- Keith __ My mind works like lightning. One brilliant flash, and it's gone. "Dick Locke" wrote in message ... On 21 Feb 2004 06:28:15 -0800, (Richard Kollmann) wrote: "Rick & Linda Bernard" wrote in message ... Anyone use a small fan in their fridge to help stabilize the temperatures. I have seen a battery powered one. Any comment on their effectiveness. Installation of a small fan to tumble the air around the inside of the refrigerator box can greatly improve the efficiency of your refrigerator, for details on fan and installation; see FAQ #30 on my web site. http://www.kollmann-marine.com I have been thinking about doing that but have been putting it off due to concerns about drilling a hole through the foam insulation to get the wires in. Any words of wisdom on an easy way to do it? |
#28
|
|||
|
|||
Refrigerator Fan
In article ,
Dick Locke wrote: I've also got a drain hole in the bottom that I think is the most accesible place. The refrig lines are a bit hard to get to. Looking at it, I also found that the drain line goes into the bilge. Arrgh. I guess I'm looking at installing a foot pump to pump into the galley sink or its drain. I'd lose that drain fast. Lots of cold leaks out there. -- Jere Lull Xan-a-Deux ('73 Tanzer 28 #4 out of Tolchester, MD) Xan's Pages: http://members.dca.net/jerelull/X-Main.html Our BVI FAQs (290+ pics) http://homepage.mac.com/jerelull/BVI/ |
#29
|
|||
|
|||
Refrigerator Fan
In article ,
Dick Locke wrote: I've also got a drain hole in the bottom that I think is the most accesible place. The refrig lines are a bit hard to get to. Looking at it, I also found that the drain line goes into the bilge. Arrgh. I guess I'm looking at installing a foot pump to pump into the galley sink or its drain. I'd lose that drain fast. Lots of cold leaks out there. -- Jere Lull Xan-a-Deux ('73 Tanzer 28 #4 out of Tolchester, MD) Xan's Pages: http://members.dca.net/jerelull/X-Main.html Our BVI FAQs (290+ pics) http://homepage.mac.com/jerelull/BVI/ |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|