Home |
Search |
Today's Posts |
|
#1
posted to rec.boats.cruising,uk.rec.sailing
|
|||
|
|||
Volvo MD7A overheating
On Sun, 21 Dec 2008 17:43:45 -0800, "Capt. JG"
wrote: "Bruce In Bangkok" wrote in message .. . On Sun, 21 Dec 2008 15:38:40 -0500, hpeer wrote: I have Volvo MD7A, 13 hp two cylinder unit with salt water cooling. Runs perfectly with one exception, it occasionally overheats and I can't figure out what the heck is going on. I bought the boat used and the previous owner had fitter her out himself. Every time she overheats, I find something to "fix" after which she is fine for a spell then she will overheat again. Clearly I'm not getting to the root cause. Generally she will seem to be running along just fine and all of a sudden the pressure gauge just goes up, up, up. It seems to be a bi-state kind of thing, it either works perfectly well or not at all. Its almost as if there is a ball valve or something somewhere that is sticking. It's obviously not a bad gage. The plumbing goes like this: Through hull fitting Salt water strainer Tap to the transmission/engine Tap to secondary pick up from bilge Tap to sinks Here is some of the history and what I had done, in each case I have also checked/changed the impeller. They usually look just perfect. 1: Recently fitted salt water strainer seemed to be blocked with debris from its construction. It is home built out of some interlocking pieces of PVC pipe, the inner piece has a zillion small holes drilled in it. I dumped this stuff out and she was fine. 2: Found a small leak in the copper pipe from the transmission to the impeller. I thought that maybe it was sucking in air and the impeller was getting air bound. Repaired the leak. 3: Moved and lowered the salt water strainer. This was mounted pretty high on a bulkhead with real long hoses. I moved it to the engine compartment and lowered it. I thought that maybe there was just too much suction head to get the water going. 4: Threw thermostat overboard. Any clues? Many thanks, Howard I am the process of rebuilding my own raw water cooling and have the following comments about yours: The usual configuration for the engine cooling is Thru-hull to Strainer to xmission cooler to water pump to oil cooler to engine to exhaust elbow and overboard. You used the word "tap" to indicate connections to the transmission cooler. This should be the entire flow from the strainer to the pump, i.e., hose from strainer to xmission cooler to pump. The hose from the thru-hull to the strainer to the cooler to the pump and onward to the engine should be the full size of the thru-hull (if possible). If you are going to install "taps" in the line for uses other then engine cooling you MUST be sure that these taps are isolated with valves and not used while the engine is running. The main strainer should/must be located below the water line so that with the sea cock open the strainer fills. If this is an old engine and it has not been flushed after every use in salt water, which is seldom/never done you probably have scale built up inside the engine that could be blocking water passages. This scale will not dissolve in fresh water, by the way. There are acid flushes which will remove it but I do not have a formula. Perhaps google if you feel this might be a problem. Regarding water coming out the exhaust. It is not an accurate indicator of anything except that water is getting through. In my own case there ~appears~ to be normal amounts of water out the exhaust but the engine overheated over 1800 RPM due to restrictions in the inlet line to the pump. By the way, you DO want a strainer in the line to keep stuff out of the system. I have removed plastic bags from the main strainer as well as small creatures, weeds, mud, small sticks and innumerable things that you probably don't want in the engine or pump. Cheers, Bruce (bruceinbangkokatgmaildotcom) He said it was an intermittent problem... so does your situation reflect the same sort of over-heating? Yes it was intermittent... until the gunk built up so much that it became continuous. Cheers, Bruce (bruceinbangkokatgmaildotcom) |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Volvo Penta V8 Overheating | General | |||
Volvo MD7A raw-water cooling flush | General | |||
Volvo MD7A raw-water cooling flush | General | |||
Volvo MD7A and MD5A difference?? | Cruising | |||
Need Exhaust Manifold (volvo MD7A) | Cruising |