Home |
Search |
Today's Posts |
#1
|
|||
|
|||
Stevenson Projects Micro-Cup
Has anybody built this boat? Do you reccomend any changes.
Considering the age of the plans, are there any materials other than 1/4" ply that would be lighter? I am interested in building two for my kids. |
#2
|
|||
|
|||
Stevenson Projects Micro-Cup
My sons are building one of Stevenson's Amphora's now. This was a design
from 1973 or so. We substitute as needed to update. Epoxy resin now instead of two part glue then, etc. Try this link for more information: http://www.messing-about.com/ Greg Luckett "Parallax" wrote in message m... Has anybody built this boat? Do you reccomend any changes. Considering the age of the plans, are there any materials other than 1/4" ply that would be lighter? I am interested in building two for my kids. -----= Posted via Newsfeeds.Com, Uncensored Usenet News =----- http://www.newsfeeds.com - The #1 Newsgroup Service in the World! -----== Over 100,000 Newsgroups - 19 Different Servers! =----- |
#3
|
|||
|
|||
Stevenson Projects Micro-Cup
I've built the Stevenson Projects MiniCup boat and have been quite happy
with it overall. You may want to check out the MiniCup FAQ at http://www.byyb.org/pn/modules.php?o...y es&id_cat=9 or go to the http://www.byyb.org site and follow the links. There's also some information on my own website - http://www.floatingbear.ca/ My own opinion is that although you could build the boat out 1/8" ply you would have some loss of hull strength as well as having problems fastening such thin ply to the stringers. -- Andrew Butchart http://www.floatingbear.ca "Parallax" wrote in message m... Has anybody built this boat? Do you reccomend any changes. Considering the age of the plans, are there any materials other than 1/4" ply that would be lighter? I am interested in building two for my kids. |
#4
|
|||
|
|||
Stevenson Projects Micro-Cup
"Andrew Butchart" wrote in message ...
I've built the Stevenson Projects MiniCup boat and have been quite happy with it overall. You may want to check out the MiniCup FAQ at http://www.byyb.org/pn/modules.php?o...y es&id_cat=9 or go to the http://www.byyb.org site and follow the links. There's also some information on my own website - http://www.floatingbear.ca/ My own opinion is that although you could build the boat out 1/8" ply you would have some loss of hull strength as well as having problems fastening such thin ply to the stringers. -- Andrew Butchart http://www.floatingbear.ca "Parallax" wrote in message m... Has anybody built this boat? Do you reccomend any changes. Considering the age of the plans, are there any materials other than 1/4" ply that would be lighter? I am interested in building two for my kids. Thanks for the info. |
#6
|
|||
|
|||
Stevenson Projects Micro-Cup
(Parallax) wrote in message om...
(Parallax) wrote in message . com... "Andrew Butchart" wrote in message ... I've built the Stevenson Projects MiniCup boat and have been quite happy with it overall. You may want to check out the MiniCup FAQ at http://www.byyb.org/pn/modules.php?o...y es&id_cat=9 or go to the http://www.byyb.org site and follow the links. There's also some information on my own website - http://www.floatingbear.ca/ My own opinion is that although you could build the boat out 1/8" ply you would have some loss of hull strength as well as having problems fastening such thin ply to the stringers. -- Andrew Butchart http://www.floatingbear.ca "Parallax" wrote in message m... Has anybody built this boat? Do you reccomend any changes. Considering the age of the plans, are there any materials other than 1/4" ply that would be lighter? I am interested in building two for my kids. Thanks for the info. Day 1. Bought the wood, 10 pieces of 4' X 8' X 1/4" Luan underlayment (I am building 2). This stuff is very light and nicely finished. Several ppl told me to get Mahogany instead of Fir for the stringers, etc. The lumberyard had limited amounts of Fir but strongly suggested an Australian wood called Agathis which I got. This was more expensive than I thought. Before it got dark this evening, I managed to draw out on the wood the sides and centerboard box for 1, and the bow decking for it but did not have time to draw the curves. I am a little worried about cutting the luan even with taping both sides of each cut because I have seen similar stuff splinter (cutting doors). Will try to finish the lofting tomorrow evening. I am considering the sails now and although the plans call for visqueen, what about the reinforced plastic tarp material? Any ideas on sail material. The backyard yacht building site showed one with a different rig than the "latteen" style sail, it had a stayed mast. Anybody know anything about it? The plans call for the two Al poles that form the top and bottom of the sail to be the same diameter as the mast, why not make them a little smaller? Thanks, David OHara |
#7
|
|||
|
|||
Stevenson Projects Micro-Cup
(Parallax) wrote in message om...
snip not have time to draw the curves. I am a little worried about cutting the luan even with taping both sides of each cut because I have seen similar stuff splinter (cutting doors). Will try to finish the lofting tomorrow evening. I use a circular saw with a plywood cutting blade and have few problems. Set the blade so that it just barely cuts through the wood and you shouldn't have any problems. FYI - I would suggest waiting to cut out the decks until you have the rest of the hull assembled, a few people (including me) have had problems with the pieces fitting at that point. Also, there is an extra measurement you want to do on your fore and aft bulkheads to make sure they match the side bulkheads at the correct location. A few people (including me) have had problems with that. Also, even though I used fir myself for my MiniCup, I have since switched to spruce which is much cheaper where I live and works almost as well. Good luck with the project. Andrew Butchart |
#8
|
|||
|
|||
Stevenson Projects Micro-Cup
(Andrew Butchart) wrote in message . com...
(Parallax) wrote in message om... snip not have time to draw the curves. I am a little worried about cutting the luan even with taping both sides of each cut because I have seen similar stuff splinter (cutting doors). Will try to finish the lofting tomorrow evening. I use a circular saw with a plywood cutting blade and have few problems. Set the blade so that it just barely cuts through the wood and you shouldn't have any problems. FYI - I would suggest waiting to cut out the decks until you have the rest of the hull assembled, a few people (including me) have had problems with the pieces fitting at that point. Also, there is an extra measurement you want to do on your fore and aft bulkheads to make sure they match the side bulkheads at the correct location. A few people (including me) have had problems with that. Also, even though I used fir myself for my MiniCup, I have since switched to spruce which is much cheaper where I live and works almost as well. Good luck with the project. Andrew Butchart Thanks for the advice as I had planned to cut out the decks tomorrow but will wait. Day 2. Finished drawing the decks and cockpit. |
#9
|
|||
|
|||
Stevenson Projects Micro-Cup
(Parallax) wrote in message . com...
(Andrew Butchart) wrote in message . com... (Parallax) wrote in message om... snip not have time to draw the curves. I am a little worried about cutting the luan even with taping both sides of each cut because I have seen similar stuff splinter (cutting doors). Will try to finish the lofting tomorrow evening. I use a circular saw with a plywood cutting blade and have few problems. Set the blade so that it just barely cuts through the wood and you shouldn't have any problems. FYI - I would suggest waiting to cut out the decks until you have the rest of the hull assembled, a few people (including me) have had problems with the pieces fitting at that point. Also, there is an extra measurement you want to do on your fore and aft bulkheads to make sure they match the side bulkheads at the correct location. A few people (including me) have had problems with that. Also, even though I used fir myself for my MiniCup, I have since switched to spruce which is much cheaper where I live and works almost as well. Good luck with the project. Andrew Butchart Thanks for the advice as I had planned to cut out the decks tomorrow but will wait. Day 2. Finished drawing the decks and cockpit. Day 3. Drew the bulkheads and transoms I am only drawing one set of deck and bulk/transom drawings because I plan to use the first set as a template to draw the second (am making two boats). I did draw two sets of sides and cebterboard well sides. |
#10
|
|||
|
|||
Stevenson Projects Micro-Cup
(Parallax) wrote in message om...
(Parallax) wrote in message . com... (Andrew Butchart) wrote in message . com... (Parallax) wrote in message om... snip not have time to draw the curves. I am a little worried about cutting the luan even with taping both sides of each cut because I have seen similar stuff splinter (cutting doors). Will try to finish the lofting tomorrow evening. I use a circular saw with a plywood cutting blade and have few problems. Set the blade so that it just barely cuts through the wood and you shouldn't have any problems. FYI - I would suggest waiting to cut out the decks until you have the rest of the hull assembled, a few people (including me) have had problems with the pieces fitting at that point. Also, there is an extra measurement you want to do on your fore and aft bulkheads to make sure they match the side bulkheads at the correct location. A few people (including me) have had problems with that. Also, even though I used fir myself for my MiniCup, I have since switched to spruce which is much cheaper where I live and works almost as well. Good luck with the project. Andrew Butchart Thanks for the advice as I had planned to cut out the decks tomorrow but will wait. Day 2. Finished drawing the decks and cockpit. Day 3. Drew the bulkheads and transoms I am only drawing one set of deck and bulk/transom drawings because I plan to use the first set as a template to draw the second (am making two boats). I did draw two sets of sides and cebterboard well sides. Fri: Just made the joiner piece for the hull bottom. Couldnt find a batten long enough to make the curve so first calculated the radii of curvature and tried to draw the curves using a pen tied on a long string. Apparently too much stretch in the string. Found a piece of long thin stock at work and used it to draw the curve. Cut two of them out (two boats) on a bandsaw and finished them on a table sander. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Stevenson Projects MiniCup 12' sailboat - MiniCup.pdf (0/1) | Boat Building | |||
Winter Boat Projects...who's got some? | General |