Are you sure you can't get 3mm baltic birch ply locally?
It seems to be very popular for making drawer bottoms. Cheap and strong too.
I think 3mm should be flexible enough to cold mould the way you want.


"Kevin" wrote in message
om...
Well I tried to bend 6mm plywood around my buck (As described in a
previous thread), and after steaming it for almost an hour, got
absolutely no where. As I can not find 2mm or 3mm okoume any where
locally, and shipping it seems pretty prohibitive ($50.00 packaging
fee for one sheet???!!).... I have found a source for 1.5mm Finnish
Baltic Birch 3 ply (AirCraft Grade) in 4' x 4' sheets. The supplier
says it can be rolled and shipped via ups in a mailing tube.... so I
guess it can be made to conform to my buck. Anyone aware of any
reasons not to "cold mold" several layers of baltic birch ply? It will
be epoxy, four layers of 1.5mm baltic birch glued with epoxy (I am
hopping that the epoxy in between the birch will fill out the sandwich
a little for a 9mm width) and a layer of 6oz fibre glass on the
outside.....

I can however buy 4mm 3 ply bs1088 okoume locally, but am wary of
being able to bend it after steaming to my desired radius.

comments appreciated.

Kevin

The problem with the local 3mm baltic birch that I have been able to
find is that it only has interior grade glue.... which I don't think
will hold up.

Kevin

"Trent Hink" wrote in message ...
Are you sure you can't get 3mm baltic birch ply locally?
It seems to be very popular for making drawer bottoms. Cheap and strong too.
I think 3mm should be flexible enough to cold mould the way you want.

Yes standard Baltic (actually Russian) birch is not even slightly water
resistant.

Kevin wrote:
The problem with the local 3mm baltic birch that I have been able to
find is that it only has interior grade glue.... which I don't think
will hold up.

Kevin


"Trent Hink" wrote in message ...
Are you sure you can't get 3mm baltic birch ply locally?
It seems to be very popular for making drawer bottoms. Cheap and strong too.
I think 3mm should be flexible enough to cold mould the way you want.

--
Glenn Ashmore

I'm building a 45' cutter in strip/composite. Watch my progress (or lack
there of) at: http://www.rutuonline.com
Shameless Commercial Division: http://www.spade-anchor-us.com

Glenn Ashmore wrote in message news:DDZGb.11259$JD6.7487@lakeread04...
Yes standard Baltic (actually Russian) birch is not even slightly water
resistant.

Sure is nice for making scale models though
Scotty


Kevin wrote:
The problem with the local 3mm baltic birch that I have been able to
find is that it only has interior grade glue.... which I don't think
will hold up.

Kevin


"Trent Hink" wrote in message ...
Are you sure you can't get 3mm baltic birch ply locally?
It seems to be very popular for making drawer bottoms. Cheap and strong too.
I think 3mm should be flexible enough to cold mould the way you want.

It seems to hold up very well for these:
http://gallery.kiteforum.com/gallery/albup46
But I always thoroughly coat it with epoxy and sometimes vacuum bag a layer
of glass on as well. Note the tortured shape, from 3 layers 3mm laminated
with rocker and bottom concave.

Nice springy "pop" like a snowboard. At 180lbs with frequent jumps to around
15', I haven't been able to break one or seen any signs of rot yet, even the
ones where I ground through to to bare wood riding over sand and (sometimes)
rocks.

Then again this is not an application where the wood is submerged for much
more than a few hours at a time.



"Glenn Ashmore" wrote in message
newsDZGb.11259$JD6.7487@lakeread04...
Yes standard Baltic (actually Russian) birch is not even slightly water
resistant.

Kevin wrote:
The problem with the local 3mm baltic birch that I have been able to
find is that it only has interior grade glue.... which I don't think
will hold up.

Kevin


"Trent Hink" wrote in message
...
Are you sure you can't get 3mm baltic birch ply locally?
It seems to be very popular for making drawer bottoms. Cheap and strong
too.
I think 3mm should be flexible enough to cold mould the way you want.

--
Glenn Ashmore

I'm building a 45' cutter in strip/composite. Watch my progress (or lack
there of) at: http://www.rutuonline.com
Shameless Commercial Division: http://www.spade-anchor-us.com

Did so more searching and found sources localy for:

1- 3 Ply 3mm (1/8 inch) Italian Poplar called Bending Poplar

2- 3 Ply 2.7 mm meranti VC (What does the VC mean?)

3- 2 Ply 2.7 mm meranti

4- 3 Ply 2.7 mm meranti A-3 VC (I assume this is grading
information... somoene want to decode it for me?)

5- 3 Ply 3mm Obeche


Which would be my best option for my rounded driftboat transom, and
what are the various strenghts and weaknesses of the above listed
woods?

Thanks in advance,
Kevin

Just got back from the supplier on the above mentioned ply and
discovered that it was all exterior glue.... looks like I will most
likely ored in the 1.5 mm finnish birch from an aircraft supply co. It
is rated finnish grade gl-11 anyone know if this is water proof?

Kevin

Aircraft rated ply is one step beyond marine rated: specifically, it
must have no voids and no patches in any ply, and be waterproof glue
laminated.

Brian W

On 29 Dec 2003 11:05:49 -0800, (Kevin) wrote:

Just got back from the supplier on the above mentioned ply and
discovered that it was all exterior glue.... looks like I will most
likely ored in the 1.5 mm finnish birch from an aircraft supply co. It
is rated finnish grade gl-11 anyone know if this is water proof?

Kevin

make that finnish grade gl-2 on my previos post.

Kevin

My brain must not be fully in gear today.....
the problem with the long list of ply that I found is that it was all
interior grade glue... not exterior as I stated above (guess the
mental clutch is slipping).

So now I think I will either do a layer of 1.5mm gl-2 finnish birch
followed by 6mm of chopped glass and resin, topped by another 1.5mm
birch ply (for 9mm of material) or 4 layers of the birch sandwiched
out with glass & epoxy to the desired 9mm.

Which of the above techniques will be stronger?

The birch is sold in 4'x4' sheets at around $24.00 a sheet plus
shipping (about $10.00). I am trying to also decide which will be more
cost effective as I haven't decided wich is more expensive, an extra
sheet of birch or the epoxy and glass needed to build a 6mm inner
core.

Any thoughts on which technique is more cost effective?

As for bending:

I will soak the birch in a very hot bath, throw in some amonia (into
the hot bath), and spot spray with water & heat it with a flat iron as
needed while applying it (a technique I saw described in one of the
model airplane building groups where the guy said he wrapped 6 inches
1.5mm around a pencil, in a very tight spiral).


Thanks,
Kevin