Home |
Search |
Today's Posts |
|
#1
posted to rec.boats
|
|||
|
|||
Engine trouble
|
#2
posted to rec.boats
|
|||
|
|||
Engine trouble
On Jun 23, 12:23*am, Larry wrote:
wrote in news:75891839-5d1f-46f6-aa2c-df6033521575 @x35g2000hsb.googlegroups.com: I had the injectors cleaned last fall and the engine was running smoothly until this happened. A '92 Mariner has injectors, not carbs?? Does it have a PRIMER BULB? Primer bulb on the fuel line? Yes I have one. Now that I think about it, it has oil injector but probably carburetor... |
#3
posted to rec.boats
|
|||
|
|||
Engine trouble
|
#4
posted to rec.boats
|
|||
|
|||
Engine trouble
On Jun 23, 10:28*am, HK wrote:
wrote: On Jun 23, 12:23 am, Larry wrote: wrote in news:75891839-5d1f-46f6-aa2c-df6033521575 @x35g2000hsb.googlegroups.com: I had the injectors cleaned last fall and the engine was running smoothly until this happened. A '92 Mariner has injectors, not carbs?? Does it have a PRIMER BULB? Primer bulb on the fuel line? Yes I have one. Now that I think about it, it has oil injector but probably carburetor... Dirty carb or carb needing rebuilding. Dirty plugs. Fouled sensor somewhere. The carb got cleaned last Fall. Was rough a bit but since it was cleaned and up until yesterday, it ran smooth. I'll check the plugs next weekend. A local shop told me to check if there is water in the gas tank. Since it's an inboard tank, it's not easy to check so I'll use a external 5gal tank (and clean fuel) and see if it runs fine. |
#5
posted to rec.boats
|
|||
|
|||
Engine trouble
|
#6
posted to rec.boats
|
|||
|
|||
Engine trouble
HK wrote in
: Stuck reeds? Jumped timing (sheared flywheel key, maybe?) Naw...It won't idle with the reeds stuck even a little open because it'll breathe back through the carb blowing gas out the intake. If the timing's jumped, it won't idle worth a crap, either. |
#8
posted to rec.boats
|
|||
|
|||
Engine trouble
On Jun 23, 4:27*pm, Larry wrote:
wrote in news:718bdca1-6c67-4451-9150- : A local shop told me to check if there is water in the gas tank. Since it's an inboard tank, it's not easy to check so I'll use a external 5gal tank (and clean fuel) and see if it runs fine. Stop by any auto parts store and buy a see-through fuel filter that has the right sized hose fittings on it, same as the primer bulb. *Buy an extra length of fuel hose that will run from the primer bulb to the gas filler cap so we can use the bulb to pump gas from the bottom of the tank through that filter back into the tank by hand to see what's in the fuel. * Make sure you can lay the filter on its side so we can look under the filter paper while pumping the bulb. Disconnect the motor from the bulb (don't forget we need a new hose clamp to put it back). *Connect a short piece of hose from the bulb to the OUTSIDE-the-paper filter end of the see thru filter. *We're going to pump gas from the OUTSIDE of the filter paper to the inside and back into the tank so we can see what crap will collect on the outside of the paper. From the INSIDE end of the filter, run the hose DEEPLY into the filler cap so we don't make a lot of wasteful fumes trying to spray it in the cap. *We don't need to see it going back in the tank because we can see the filter. Pump the bulb, the more the better, the faster the better....with theboatrocking at the dock sloshing the crap in the tank around is best! * Put theboatin the water and tie it to a dock that has waves to slosh it around for us free. *Do NOT let the outlet end of the filter be lower than the inlet end. *We want water to show up in the filter if it's there (which I'm betting it's not unless you left the gas tank NEARLY EMPTY all winter. *You DID FILL THE TANK BEFORE STORAGE EVERY TIME, RIGHT?!! *Flog yourself if you didn't for me! *Shame on you! Full gas tanks cannot BREATHE in water vapor to collect on cold, bare tank walls every night....ALWAYS leave the tanks stored FULL, but not overflowing..... I had to go to the cottage yesterday (got broken into but they caught the *******s so I didn't lose much) and it gave me a chance to try to the boat. First I had to fix the throttle because the robbers were too dumb to know to try another key in the key chain instead of breaking my gas cap lock key in the ignition switch! Back to the boat... Started it and it works fine, no hesitation at all... What gives??? Oh yeah, while fixing the throttle, I removed the red cables from the batteries and when I put it back (the big one, not the small one for accessories) it created a spark! There was nothing on (no light, bilge pump, well fan, etc). I followed the wire to the engine were it connected to other red cables. I undid then and touched the main cable one by one. The one that created a spark was the voltage regulator one. I had it changed last year. Could it be a faulty one? Is it supposed to drain the batteries like that? I doubt it though... Thanks again! |
#9
posted to rec.boats
|
|||
|
|||
Engine trouble
It did it again (no power at low rpm until 3,400 rpm) :-(
I noticed the engine would start with just either the top or center cylinder plug connected but not the lower cylinder plug connected. I swapped the lower cylinder plug with the top cylinder one and it still wouldn't start with the lower cylinder only so I know if wasn't a foul plug. I swapped the center and lower coil (and wires as well so the timing was still ok )and same thing, the center plug was working with the lower coil but not the lower plug with the center coil so again, I deducted the coils are ok. Only one thing left... The electronic module :-( With my problem with the voltage regulator and the now the electronic module, the boat is in the shop for a checkup :-( |
#10
posted to rec.boats
|
|||
|
|||
Engine trouble
wrote in news:7bc30477-49a6-401e-81e2-
: Primer bulb on the fuel line? Yes I have one. Now that I think about it, it has oil injector but probably carburetor... Ok, first we need to use the primer bulb to test the fuel system for operation, clogged lines, stuck floats, ripped open rubber diaphram in the chinzy-ass fuel pump: Tilt the engine down to its operating position. Pump the primer bulb until it gets so hard you can't pump it any more. Keep that last squeeze on it to see if it slowly squeezes down. You have now pressurized the fuel system inside the engine, having filled the carb floats until the float valves shut off the flow. The pressure from your priming has also showed us there are no leaks because the bulb won't pump up hard if there are, it'll slowly squeeze and gas will run out "somewhere", even places you can't see. We've also learned the diaphram in the cheap pulse fuel pump doesn't have a rip or hole in it because if it did you'd be pumping gas through the hole into one of the cylinder's crankcase, flooding it with gas and the bulb will NEVER get hard that way. Now, IF you pumped that first pump or two and the bulb stayed flat and refused to refill from the tank, you either have a clogged strainer inside the tank...or you forgot to turn on the fuel tank exit valve....or you have a clogged external fuel filter if it exists. You need to find out why the bulb can't pump gas freely as it's clogged up. Isn't this easy?! Ok, we pumped the bulb at the dock until it got hard. It stayed hard even though we continued to squeeze it on that last squeeze when it got hard and didn't notice it slowly bleeding off our last squeeze. That all went well, let's go to sea trials.....more testing with this little bulb! Ok, now we need to WATCH the primer bulb before and after the engine runs like crap. We've primed the engine, already during the initial static testing phase. Crank 'er up and let it idle at the dock. If it idles like crap and we've already primed it, the low speed jets are probably clogged or we have an ignition problem. That's about all there is to a 2-stroke engine. Let's say it idles fine, well, as fine as a 2-stroke ever idles. Idle out past the boats and docks into open water and have someone ELSE keep an eye on the bulb. Don't pump it....yet. If the bulb starts to collapse on its own at any time, OPEN THE GAS CAP A CRACK and see if it fills back out....the fuel tank vent is clogged if it fills back out! Damned dirt daubers! Clear the vent, close the gas cap and try again to see if you got all the mud out of it the wasps put in. Ok, still watching the bulb for any signs of collapse, out in open water, start running the throttle up and onto plane, normally not all at once. If the bulb starts to collapse at any point, open the gas cap again and see if it refills out again. The vent is ALMOST clogged if that works. Ok, we're on plane and watching the bulb. The bulb didn't collapse but the engine started running like crap. Start to pump the bulb while the engine is running like crap. If the engine smooths back out and picks up speed, keep pumping the bulb until we get back to the dock. The fuel pump pulse line hose has a hole in it, has fallen off or is partially clogged so the crankcase gasses pumping the little diaphram in and out aren't pumping the little diaphram in and out. The diaphram was fine in our static test, but the pulse line that pulses the diaphram is blocked or leaking too bad to pump it....we ran outa gas in the carbs.... You'd be amazed at the number of boats who asked me to tow them were just so amazed when I told them to try that last paragraph so they could get back to the trailer...(c; Panicky people aren't too diagnostic of problems. Ok, we pumped the bulb and it didn't change the way the engine was running at all...it still runs like crap. Two possiblities, now, clogged high speed jets because you put the toys away WITHOUT draining the carbs by unplugging the motor at the dock and letting it run until it died from lack of gas.....or ignition problems, probably caused by the cheap-assed stator under the flywheel being all rusted up because it would have cost Mariner (or any of them) another dollar to PAINT the iron core that's shorting out....damn them all. Take it to the shop and tell them exactly what you did from my post to help them find the problem. I'm already assuming you can see water pouring out of the ****er and you see water sputtering out of the exhaust relief letting us know the thermostats have opened and it's not overheating...right? It could still have a leaky head gasket or cracked rings but I don't suppose you have a cylinder pressure guage to test it or you wouldn't have posted what you posted. ---------------------------------------------------------- The look on a boater's face when I tell him to open the gas cap a crack, or the fuel valve he forgot to open, and the engine smooths out in 15 seconds, having watched his bulb collapse..........PRICELESS!...(C; |
Reply |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
trouble starting engine when solar panels are working | Cruising | |||
Engine trouble the other day on my boat. - rta96c_crank.jpg | Tall Ship Photos | |||
trouble starting engine | Cruising | |||
Trouble Starting engine | Cruising | |||
1986 - 50 HP Mercury Engine Trouble | General |