Dry Suit Seals: Temporary Repairs?
 

Per Davej:
So each time you replace a seal do you add another layer of rubber?
What if the original rubber layer gets really bad?

The limit's supposedly 3 layers.

The right amount of heat lets them be peeled off.

IIRC Kokatat recommends the use of a clothes iron.
--
PeteCresswell

Dry Suit Seals: Temporary Repairs?
 

Davej wrote:
Brian Nystrom wrote:
(PeteCresswell) wrote:
Per Brian Nystrom:
For that matter, you can use tube patches to repair rips and holes or to
reinforce damaged edges. However, it's not difficult to replace the seal
and be done with it.
In the past, I'd been doing my neck seals on the hood of my car: lay it flat,
use 30-40 little magnets to hold it all together. My best time was about
45 minutes for a neck seal and 2 wrist seals.

Just did the last two neck seals with the jigs that Kokatat describes: a ring, a
plate to clamp the ring to, and a smaller plate to give the top of the seal some
shape.

The wood I cut the jigs from was way too thick - about 3/4"... Didn't put a
clock on it, but it was pretty impressive how simple the process became
alignment-wise.

If I can find some 1/4" polyethylene sheet to cut another set of jigs from, I
think it'll be even easier bc the only downside was having to separate the
seals/dryed glue from the wood.
I used 3/8" plywood for my forms and it works well. I use clear packing
tape to cover the areas that are likely to be exposed to glue.

So each time you replace a seal do you add another layer of rubber?

No, I peel off the top layer and bond the new seal to the original. OS
Systems seal glue makes this pretty easy, as all it takes is a heat gun
to soften it.

What if the original rubber layer gets really bad?

I haven't had that problem yet. If/when it happens, I'll remove the old
seal material and glue the new seal directly to the fabric.

Dry Suit Seals: Temporary Repairs?
 

Dry Suit Seals: Temporary Repairs?
 

Per Davej:
Ok, I will give this a try. It says to clean first with cotol, paint
thinner, or nail polish remover. I wonder which is least toxic?

I've been using 70% denatured alcohol (the stuff available at
drugstores/supermarkets) without any glue/adhesion problems.
--
PeteCresswell

Dry Suit Seals: Temporary Repairs?
 

"(PeteCresswell)" wrote:
Davej wrote:

Ok, I will give this a try. It says to clean first with cotol, paint
thinner, or nail polish remover. I wonder which is least toxic?

I've been using 70% denatured alcohol (the stuff available at
drugstores/supermarkets) without any glue/adhesion problems.

Denatured not isopropyl? Thanks.

Dry Suit Seals: Temporary Repairs?
 

Davej wrote:
"(PeteCresswell)" wrote:
Davej wrote:

Ok, I will give this a try. It says to clean first with cotol, paint
thinner, or nail polish remover. I wonder which is least toxic?
I've been using 70% denatured alcohol (the stuff available at
drugstores/supermarkets) without any glue/adhesion problems.

Denatured not isopropyl? Thanks.

Drug store alcohol is isopropyl, not denatured. Denatured alcohol
(ethanol with enough methanol added to make it undrinkable) is found at
hardware and paint stores, and is commonly used as a thinner for shellac
and as a mild, general-purpose degreaser. Either one will work, but MEK
works better, though it's more toxic.

Dry Suit Seals: Temporary Repairs?
 

Per Davej:
Denatured not isopropyl? Thanks.

Oops!.... Mea culpa.

The label says isopropyl.

I thought they were one and the same.
--
PeteCresswell

Dry Suit Seals: Temporary Repairs?
 

On Jan 24, 7:21 pm, Brian Nystrom wrote:
Davej wrote:
"(PeteCresswell)" wrote:
Davej wrote:
Ok, I will give this a try. It says to clean first with cotol, paint
thinner, or nail polish remover. I wonder which is least toxic?
I've been using 70% denatured alcohol (the stuff available at
drugstores/supermarkets) without any glue/adhesion problems.

Denatured not isopropyl? Thanks.

Drug store alcohol is isopropyl, not denatured. Denatured alcohol
(ethanol with enough methanol added to make it undrinkable) is found at
hardware and paint stores, and is commonly used as a thinner for shellac
and as a mild, general-purpose degreaser. Either one will work, but MEK
works better, though it's more toxic.

I have acetone, mineral spirits, and two grades of isopropyl. Maybe
I'll experiment.

Dry Suit Seals: Temporary Repairs?
 

Davej wrote:

I have acetone, mineral spirits, and two grades of isopropyl. Maybe
I'll experiment.

Don't use mineral spirits. It's oily and potentially harmful to latex.

The difference between commonly sold isopropyl alcohols is the water
content. They're usually either 70% or 91% alcohol (sold as rubbing
alcohol), though you can get 99.9+% isopropyl that's sold for other
purposes (electronics cleaning, for one). The more water, the longer it
will take to dry after cleaning, so there's no advantage to using the
more dilute grade.

Dry Suit Seals: Temporary Repairs?
 

On Jan 19, 5:01 pm, "(PeteCresswell)" wrote:
Per :

Old inner tubes and Aquaseal has worked for me.

Now that somebody's said it, I'd think bicycle inner tubes would be good -
thinner, more flexy.... and they're available in different materials, although I
don't have a clue what the significance on one material vs the other would be
for gasket repair.


Well, I decided to try using rubber electrical tape since it is
thinner than the bicycle inner tube, but it didn't work well. The
surface of the tape seems to be too slippery. Maybe I need to rough it
up with sandpaper -- or maybe it isn't a compatible material?
Basically it seems that repairs are only possible where the seal
doesn't stretch much. Where would I go for seals for a Henri Lloyd?
Are sleeve diameters standardized? Thanks.