wrote in message
ups.com...
I left the boat in the driveway for one year without starting the
motor. Today, I put the lower unit into a bucket of water, and start
the motor to winterize it. After trying to start it for a couple
times, I finally manage to start it. Unfortunately, I cannot see the
telltail water stream coming out from the motor cooling system. All I
see is some smoke coming from the hole where the water stream is
supposed to come out from. Despite the fact that the motor temperature
was not overheating (only run it for 30 seconds or so), I decided to
turn off the motor just to be in the safe side.

My question is:

Should I expect to see the telltail water stream coming out from the
motor as soon as I start the motor?

Yes.

Does the motor need to reach a
certain temperature before the water stream coming out?

No.

The impeller is shot. Any easy replacement. Here is one source for the
replacement kit.

http://www.outboardparts.com/mercury...repairkits.htm

" JimH" not telling you @ pffftt.com wrote in message
. ..

wrote in message
ups.com...
I left the boat in the driveway for one year without starting the
motor. Today, I put the lower unit into a bucket of water, and start
the motor to winterize it. After trying to start it for a couple
times, I finally manage to start it. Unfortunately, I cannot see the
telltail water stream coming out from the motor cooling system. All I
see is some smoke coming from the hole where the water stream is
supposed to come out from. Despite the fact that the motor temperature
was not overheating (only run it for 30 seconds or so), I decided to
turn off the motor just to be in the safe side.

My question is:

Should I expect to see the telltail water stream coming out from the
motor as soon as I start the motor?

Yes.

Does the motor need to reach a
certain temperature before the water stream coming out?

No.

The impeller is shot. An easy replacement. Here is one source for the
replacement kit.

http://www.outboardparts.com/mercury...repairkits.htm




edit ('an', not 'any')

JimH wrote:
wrote in message
ups.com...
I left the boat in the driveway for one year without starting the
motor. Today, I put the lower unit into a bucket of water, and start
the motor to winterize it. After trying to start it for a couple
times, I finally manage to start it. Unfortunately, I cannot see the
telltail water stream coming out from the motor cooling system. All I
see is some smoke coming from the hole where the water stream is
supposed to come out from. Despite the fact that the motor temperature
was not overheating (only run it for 30 seconds or so), I decided to
turn off the motor just to be in the safe side.

My question is:

Should I expect to see the telltail water stream coming out from the
motor as soon as I start the motor?

Yes.

Does the motor need to reach a
certain temperature before the water stream coming out?

No.

The impeller is shot. Any easy replacement. Here is one source for the
replacement kit.

http://www.outboardparts.com/mercury...repairkits.htm

Thanks for pointing out that I likely need to replace the impeller.
And also thanks for the link to the impeller kit; I quite likely need
to order one.

Now, I need to write down on my boat-owner manual to expect to see the
telltail right after I have started the motor -- to prevent it from
confusing me again.

Jay Chan

wrote in message
oups.com...


Now, I need to write down on my boat-owner manual to expect to see the
telltail right after I have started the motor -- to prevent it from
confusing me again.

Seriously??? Do you plan on looking at the manual every time you start the
motor? Checking for cooling water should be as instinctive as making sure
your dick's not about to be bitten by your pants zipper.

JoeSpareBedroom wrote:
wrote in message
oups.com...


Now, I need to write down on my boat-owner manual to expect to see the
telltail right after I have started the motor -- to prevent it from
confusing me again.

Seriously??? Do you plan on looking at the manual every time you start the
motor? Checking for cooling water should be as instinctive as making sure
your dick's not about to be bitten by your pants zipper.

Yes, absolutely seriously. I have only used the remote-start control
to started a motor for the grand total of may be 4 times (in two
occasions) in my life (discounting the number of times when I started
small motor in rental boat by hand pulling to start). I still have a
learning curve to climb through.

Jay Chan

Some of these motors have a thermostat (my 9.9 merc does) and water will not
come out til engine reaches operating temp.
" JimH" not telling you @ pffftt.com wrote in message
. ..

wrote in message
ups.com...
I left the boat in the driveway for one year without starting the
motor. Today, I put the lower unit into a bucket of water, and start
the motor to winterize it. After trying to start it for a couple
times, I finally manage to start it. Unfortunately, I cannot see the
telltail water stream coming out from the motor cooling system. All I
see is some smoke coming from the hole where the water stream is
supposed to come out from. Despite the fact that the motor temperature
was not overheating (only run it for 30 seconds or so), I decided to
turn off the motor just to be in the safe side.

My question is:

Should I expect to see the telltail water stream coming out from the
motor as soon as I start the motor?

Yes.

Does the motor need to reach a
certain temperature before the water stream coming out?

No.

The impeller is shot. Any easy replacement. Here is one source for the
replacement kit.

http://www.outboardparts.com/mercury...repairkits.htm

FREDO wrote:
Some of these motors have a thermostat (my 9.9 merc does) and water will not
come out til engine reaches operating temp.

I was thinking along that line. But turned out this is not the case.
The telltail of my motor starts coming out as soon as I put the lower
unit in a water bucket. I need to make sure there is enough water
depth above the top water inlet in the lower unit; otherwise, there is
not enough water pressure and the telltail will not come out, or I can
point a water hose directly at the top water inlet to apply water
pressure.

I still don't know why the ear-muff adapter doesn't work though.

Jay Chan