Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
posted to rec.boats
external usenet poster
 
First recorded activity by BoatBanter: Jul 2006
Posts: 55
Default Dead horse beating: Merc 3.0L A1 gear lube consumption

Yup - same impression with mine. $9,999.99 from Bayliner.
Something like $13,100 out the door with everything including
first-time boater accessory kit (anchor, fire bottle, fenders, etc).

So I gotta bring up another nagging issue - the engine noise,
and/or valve tapping noise at very low idle: when totally
warmed up, I hear what sounds like lifter/tappet noise.
But of late, it sound more like wrist pin/piston slap noise,
almost sounds like its 'dieseling'. But runs/sounds fine at
higher speeds. You notice any of that? (with engine cover off)

Also, found another tip that I should share with you. On mine,
very -RARELY- when I come off the throttle relitevly quick
after racing around a bit, the idle would get really really slow,
and run rough, and almost die (may have once or twice).
Anyways, I discovered that if I flip on the blower when it
gets in this mode, it goes right away.

So when you had your incident, how did you get it back to
the launch? Limp it back ? Was the vibration bad with the
bent up prop?

And Lastly, how did you and the boat survive Katrina?
(what was it like, where was the boat, where were you etc)

Thanks.


"katekebo" wrote in message
ups.com...

Mr Wizzard wrote:

Man, this is very helpful information, 'preciate dat!.
So, the rest of the boat been good/Ok to you ?

Yes, I have been very satisfied with the boat. I had zero issues with
the boat itself, and all problems have been self-inflicted. I hit
something one day and chopped off half of the skeg. The water here is
very murky so you can't see what's below. I suspect it was a block of
concrete or something like that. This happened when the boat was very
new, over one year ago, and it was nicely repaired by a local boat shop
/ Mercruiser dealer - they cut off the old skeg and welded a new one in
its place - you really can't see that it's not original.

I also had to replace the prop because the original one was bent /
damaged in the same incident. I opted to replace the prop with the
stock aluminum one. It gives me decent performance, and I prefer to
use a "soft" and weak prop, so in case I hit something again, the prop
will sacrificy itself instead of stripping the gears.

As for the boat, it's very austere, but that's why I like it - there
are few things to go wrong and take care of. I do all the maintenance
myself. I use it mostly on the local bayous and lake Pontchartrain -
it's a big lake and it develops a nasty chop on windy days. I also
like the fact that it's easy to tow, and I can still get 22 mpg even
when towing the boat.

Of course there are better boats. Ideally I would prefer to have a
four-stroke outboard motor and higher freeboard, but similar sized
boats with these characteristics are at least 50% more expensive. So
for the price, the 175 is unbeatable. Actually most people I have
talked with here can't believe that I paid so little for a brand-new
boat - they expect the boat to cost at least 20 to 30% more.



Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is Off
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Mercruiser A-1 gear lube consumption Mr Wizzard General 30 August 17th 06 06:39 AM
Why the word "dead" is not used in the context of deduced navigation JAXAshby General 49 August 7th 04 11:45 PM
Flogging a Dead Horse (on topic) Gould 0738 General 3 July 23rd 04 11:18 AM
Merc 3.0L Alpha 1 stuck in gear Advise Please?? LNski General 3 June 2nd 04 03:35 PM


All times are GMT +1. The time now is 08:36 AM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 BoatBanter.com.
The comments are property of their posters.
 

About Us

"It's about Boats"

 

Copyright © 2017