"Frogwatch" wrote in message
...

On Mar 24, 10:18 pm, wrote:
On Thu, 24 Mar 2011 17:57:34 -0700 (PDT), Frogwatch

wrote:
Got my fully tinned wire for my trailer and put it on so now I have
trailer lights again. However while doing it, I found that all of the
bolts and nuts on the trailer are so badly corroded they will not last
another season. I probably need about $100 of stainless hardware to
replace them. I thought EZ Loader was quality but it isn't. What
would a bit of stainless or hot dipped galv bolts have cost them?

Go to a real fastener place and you might save a few bucks but
stainless is the way to go on a salt water trailer. I started out a
couple bolts at a time as they got nasty but I bit that bullet too
after a few rounds of swapping out rusted bolts.

I ran the white ground wire to each light instead of just to the
trailer body and I hope this will prevent a few probs.

Reply:

I always did that. My EZ-loader had galvanized bolts. Broke the bolt that
holds the back cross member to the side frame one time. Actually after
about 18 years, he wore through. So I would pull those and check them.

On Mar 24, 10:18*pm, wrote:
On Thu, 24 Mar 2011 17:57:34 -0700 (PDT), Frogwatch

wrote:
Got my fully tinned wire for my trailer and put it on so now I have
trailer lights again. *However while doing it, I found that all of the
bolts and nuts on the trailer are so badly corroded they will not last
another season. *I probably need about $100 of stainless hardware to
replace them. *I thought EZ Loader was quality but it isn't. *What
would a bit of stainless or hot dipped galv bolts have cost them?

Go to a real fastener place and you might save a few bucks but
stainless is the way to go on a salt water trailer. I started out a
couple bolts at a time as they got nasty but I bit that bullet too
after a few rounds of swapping out rusted bolts.

The leaf springs are also rusting badly, not sure what to do about
them.

"Frogwatch" wrote in message
...

On Mar 24, 10:18 pm, wrote:
On Thu, 24 Mar 2011 17:57:34 -0700 (PDT), Frogwatch

wrote:
Got my fully tinned wire for my trailer and put it on so now I have
trailer lights again. However while doing it, I found that all of the
bolts and nuts on the trailer are so badly corroded they will not last
another season. I probably need about $100 of stainless hardware to
replace them. I thought EZ Loader was quality but it isn't. What
would a bit of stainless or hot dipped galv bolts have cost them?

Go to a real fastener place and you might save a few bucks but
stainless is the way to go on a salt water trailer. I started out a
couple bolts at a time as they got nasty but I bit that bullet too
after a few rounds of swapping out rusted bolts.

The leaf springs are also rusting badly, not sure what to do about
them.

*******************
By new ones if you're that concerned... they aren't very expensive.

True North wrote:


"Frogwatch" wrote in message
...

On Mar 24, 10:18 pm, wrote:
On Thu, 24 Mar 2011 17:57:34 -0700 (PDT), Frogwatch

wrote:
Got my fully tinned wire for my trailer and put it on so now I have
trailer lights again. However while doing it, I found that all of the
bolts and nuts on the trailer are so badly corroded they will not last
another season. I probably need about $100 of stainless hardware to
replace them. I thought EZ Loader was quality but it isn't. What
would a bit of stainless or hot dipped galv bolts have cost them?

Go to a real fastener place and you might save a few bucks but
stainless is the way to go on a salt water trailer. I started out a
couple bolts at a time as they got nasty but I bit that bullet too
after a few rounds of swapping out rusted bolts.

The leaf springs are also rusting badly, not sure what to do about
them.

*******************
By new ones if you're that concerned... they aren't very expensive.


If you wash your trailer after you use it, and maintain it, you'll have
far fewer problems than Froggy seems to have. Maintenance to him seems
to be "ignore it until it breaks."

Harryk wrote:
True North wrote:


"Frogwatch" wrote in message
...


On Mar 24, 10:18 pm, wrote:
On Thu, 24 Mar 2011 17:57:34 -0700 (PDT), Frogwatch

wrote:
Got my fully tinned wire for my trailer and put it on so now I have
trailer lights again. However while doing it, I found that all of the
bolts and nuts on the trailer are so badly corroded they will not last
another season. I probably need about $100 of stainless hardware to
replace them. I thought EZ Loader was quality but it isn't. What
would a bit of stainless or hot dipped galv bolts have cost them?

Go to a real fastener place and you might save a few bucks but
stainless is the way to go on a salt water trailer. I started out a
couple bolts at a time as they got nasty but I bit that bullet too
after a few rounds of swapping out rusted bolts.

The leaf springs are also rusting badly, not sure what to do about
them.

*******************
By new ones if you're that concerned... they aren't very expensive.


If you wash your trailer after you use it, and maintain it, you'll
have far fewer problems than Froggy seems to have. Maintenance to him
seems to be "ignore it until it breaks."

While I realize this is one of your signature attack posts, there is a
problem with your "advice". People who use their boats often - a
concept that is foreign to you - don't always have the luxury of rinsing
their trailers until they arrive back at the dock or their home. That
leaves a trailer in the sun for hours with sal****er on it after the launch.

On Fri, 25 Mar 2011 19:53:27 -0400, L G wrote:

Harryk wrote:
True North wrote:


"Frogwatch" wrote in message
...


On Mar 24, 10:18 pm, wrote:
On Thu, 24 Mar 2011 17:57:34 -0700 (PDT), Frogwatch

wrote:
Got my fully tinned wire for my trailer and put it on so now I have
trailer lights again. However while doing it, I found that all of the
bolts and nuts on the trailer are so badly corroded they will not last
another season. I probably need about $100 of stainless hardware to
replace them. I thought EZ Loader was quality but it isn't. What
would a bit of stainless or hot dipped galv bolts have cost them?

Go to a real fastener place and you might save a few bucks but
stainless is the way to go on a salt water trailer. I started out a
couple bolts at a time as they got nasty but I bit that bullet too
after a few rounds of swapping out rusted bolts.

The leaf springs are also rusting badly, not sure what to do about
them.

*******************
By new ones if you're that concerned... they aren't very expensive.


If you wash your trailer after you use it, and maintain it, you'll
have far fewer problems than Froggy seems to have. Maintenance to him
seems to be "ignore it until it breaks."

While I realize this is one of your signature attack posts, there is a
problem with your "advice". People who use their boats often - a
concept that is foreign to you - don't always have the luxury of rinsing
their trailers until they arrive back at the dock or their home. That
leaves a trailer in the sun for hours with sal****er on it after the launch.

You don't think Harry carried a generator, high pressure pump, and a fifty
gallon drum of fresh water in his 4Runner when he launched the 'Yo Ho'?

You just don't give people enough credit.

On Mar 25, 12:32*pm, wrote:
On Fri, 25 Mar 2011 08:24:25 -0400, Harryk
wrote:



True North wrote:

"Frogwatch" wrote in message
....

On Mar 24, 10:18 pm, wrote:
On Thu, 24 Mar 2011 17:57:34 -0700 (PDT), Frogwatch

wrote:
Got my fully tinned wire for my trailer and put it on so now I have
trailer lights again. However while doing it, I found that all of the
bolts and nuts on the trailer are so badly corroded they will not last
another season. I probably need about $100 of stainless hardware to
replace them. I thought EZ Loader was quality but it isn't. What
would a bit of stainless or hot dipped galv bolts have cost them?

Go to a real fastener place and you might save a few bucks but
stainless is the way to go on a salt water trailer. I started out a
couple bolts at a time as they got nasty but I bit that bullet too
after a few rounds of swapping out rusted bolts.

The leaf springs are also rusting badly, not sure what to do about
them.

*******************
By new ones if you're that concerned... they aren't very expensive.

If you wash your trailer after you use it, and maintain it, you'll have
far fewer problems than Froggy seems to have. Maintenance to him seems
to be "ignore it until it breaks."

Sometimes that is hard to do.

I wash the trailer after every use just after I run fresh water thru
the motor.

Frogwatch wrote:
On Mar 24, 10:18 pm, wrote:

On Thu, 24 Mar 2011 17:57:34 -0700 (PDT), Frogwatch

wrote:

Got my fully tinned wire for my trailer and put it on so now I have
trailer lights again. However while doing it, I found that all of the
bolts and nuts on the trailer are so badly corroded they will not last
another season. I probably need about $100 of stainless hardware to
replace them. I thought EZ Loader was quality but it isn't. What
would a bit of stainless or hot dipped galv bolts have cost them?

Go to a real fastener place and you might save a few bucks but
stainless is the way to go on a salt water trailer. I started out a
couple bolts at a time as they got nasty but I bit that bullet too
after a few rounds of swapping out rusted bolts.

The leaf springs are also rusting badly, not sure what to do about
them.

That would depend on how bad they are. Surface rust is one thing.
Serious corrosion is a different matter. Surface rust can be
sandblasted and coated.

On 3/24/2011 10:18 PM, wrote:
On Thu, 24 Mar 2011 17:57:34 -0700 (PDT), Frogwatch
wrote:

Got my fully tinned wire for my trailer and put it on so now I have
trailer lights again. However while doing it, I found that all of the
bolts and nuts on the trailer are so badly corroded they will not last
another season. I probably need about $100 of stainless hardware to
replace them. I thought EZ Loader was quality but it isn't. What
would a bit of stainless or hot dipped galv bolts have cost them?

Go to a real fastener place and you might save a few bucks but
stainless is the way to go on a salt water trailer. I started out a
couple bolts at a time as they got nasty but I bit that bullet too
after a few rounds of swapping out rusted bolts.

You can probably buy a box of 100 for the same price as 20 or 30 bought
loose.

On Fri, 25 Mar 2011 12:30:58 -0400, wrote:

On Fri, 25 Mar 2011 08:02:07 -0400, OmDeFlume wrote:

On 3/24/2011 10:18 PM, wrote:
On Thu, 24 Mar 2011 17:57:34 -0700 (PDT), Frogwatch
wrote:

Got my fully tinned wire for my trailer and put it on so now I have
trailer lights again. However while doing it, I found that all of the
bolts and nuts on the trailer are so badly corroded they will not last
another season. I probably need about $100 of stainless hardware to
replace them. I thought EZ Loader was quality but it isn't. What
would a bit of stainless or hot dipped galv bolts have cost them?

Go to a real fastener place and you might save a few bucks but
stainless is the way to go on a salt water trailer. I started out a
couple bolts at a time as they got nasty but I bit that bullet too
after a few rounds of swapping out rusted bolts.

You can probably buy a box of 100 for the same price as 20 or 30 bought
loose.

That was what I was getting at.

You might want to consider not replying to someone who's so juvi they
have to spoof other people.