Home |
Search |
Today's Posts |
|
#1
![]()
posted to rec.boats
|
|||
|
|||
![]() "Vic Smith" wrote in message ... Reminds me that I haven't even used a grease gun on my cars in many years. I don't even know where my grease gun is. My kid probably stole it. Man, I love modern cars. Is a '90 a modern car? --Vic My son-in-law who had a tie rod separate at 30K miles on a 2001 model didn't think so. "Permanently lubricated" is the claim. A simple zerk fitting would probably make it last for 100k miles. Eisboch (about 20 lines) |
#2
![]()
posted to rec.boats
|
|||
|
|||
![]()
On Sat, 11 Jul 2009 19:41:43 -0400, "Eisboch"
wrote: My son-in-law who had a tie rod separate at 30K miles on a 2001 model didn't think so. "Permanently lubricated" is the claim. A simple zerk fitting would probably make it last for 100k miles. What car? Probably just a defective end. You might feel them if they loosen up, but modern suspensions are pretty buffered from transmitting that. Best way is an occasional trip to a rack where a front end man can muscle stuff around to look for wear. I always have my kid check my cars out for that before going on a trip. I've heard of guys drilling ball joints and tie rod ends then using these. (It's a sel-tapping zerk.) https://www.fastenal.com/web/product...l.ex?sku=58790 Wouldn't consider it myself. Aside from keeping shavings out, it's just not necessary. --Vic |
#3
![]()
posted to rec.boats
|
|||
|
|||
![]() "Vic Smith" wrote in message ... On Sat, 11 Jul 2009 19:41:43 -0400, "Eisboch" wrote: My son-in-law who had a tie rod separate at 30K miles on a 2001 model didn't think so. "Permanently lubricated" is the claim. A simple zerk fitting would probably make it last for 100k miles. What car? Probably just a defective end. You might feel them if they loosen up, but modern suspensions are pretty buffered from transmitting that. Best way is an occasional trip to a rack where a front end man can muscle stuff around to look for wear. I always have my kid check my cars out for that before going on a trip. I've heard of guys drilling ball joints and tie rod ends then using these. (It's a sel-tapping zerk.) https://www.fastenal.com/web/product...l.ex?sku=58790 Wouldn't consider it myself. Aside from keeping shavings out, it's just not necessary. --Vic Believe it or not, I remember when the manufacturers started getting away from supplying zerk fittings in the front end components. The first couple of years, the tapped hole still existed, but it was plugged with a machine bolt. If you were so inclined, you could remove the bolt and install your own zerks. That lasted a couple of years until they supplied the tie rods, etc. without the tapped holes. Eisboch |
#4
![]()
posted to rec.boats
|
|||
|
|||
![]()
On Jul 11, 6:41*pm, "Eisboch" wrote:
"Vic Smith" wrote in message ... Reminds me that I haven't even used a grease gun on my cars in many years. *I don't even know where my grease gun is. *My kid probably stole it. Man, I love modern cars. *Is a '90 a modern car? --Vic My son-in-law who had a tie rod separate at 30K miles on a 2001 *model didn't think so. "Permanently lubricated" *is the claim. * A simple zerk fitting would probably make it last for 100k miles. Eisboch *(about 20 lines) I bet the replacement part had a "zerk" they usually do. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|