Home |
Search |
Today's Posts |
#1
posted to rec.boats
|
|||
|
|||
The Battle of The Pins...
Just a quick driveby - got some spare time this morning and I'd
thought I'd give a report on the brake actuator/solenoid problem on my trailer. It's kind of long, but interesting. The system that Ranger uses for the surge brake system is this: http://www.ufpnet.com/Portals/0/PDFs/Actuators.PDF If you scroll down, you will see a cutaway drawing - notice the two pins at the top of the actuator. The right pin is the floater pin that works the surge brake actuator, the rear pin holds the master cylinder in place. This whole system is held in place inside the trailer tongue by those same pins - pretty neat system actually. We already know about how the system failed - the brake solenoid went south when it leaked, corroded and let go. What happened next was that in the resultant slam/bang of stopping quickly, the shock absorber let go, so that needed to be replaced. Investigating with UFP, I decided to spend the $150 on the whole actuator system rather than try to replace the shock absorber and brake release solenoid - to replace the shock absorber and solenoid was going to cost $110 - seemed more cost effective to go with a whole new system. However, I needed to get the whole thing out of the trailer tongue. Thus began the Battle of The Pins. Removed the spring clips and washers - got out a five pound ball peen hammer and a cold steel drift pin - pins didn't budge. After about five minutes of whacking, I decided that was useless, so I sprayed the pins down with PB Blaster,a good soaking, and left them for eight hours to let PB Blaster work it's magic. On the second try, the pins still didn't move - hmmm. Ok, got out the twenty pound mawl and a chunk of hardened steel and really gave the pins a whack or two - nothing - didn't budge. Got out the manual, looked at the parts explosion - no spring pins holding anything in place, two plastic bushings on the rear pin and two steel bushings/rollers on the front pin. Ok, drastic measures are called for but I wasn't going to use a heat wrench - I was concerned about the trailer tongue as the pins were internal and I didn't want to heat the galvanized steel up as much as would be needed. Soaked it down with machine oil and let it sit for twelve hours - did the mawl thing again, nada, zip, zero - no movement. At this point, I gave up and took the whole thing down to my friends shop to use his hydraulic press - figured that would be the best way to do it - a little of hydraulic pressure might do the trick. Well it did - but get this - the front pin took 18 tons - yes TONS - of pressure to pop out. But a hell of a lot easier than whacking on it. On to the rear pin. I watched the pressure gauge on the press - it blew eight past 18 tons, flew by 25 tons, at 30 I was starting to get worried - this is close to explosion territory. 37 tons of pressure - 74,000 pounds and it finally moved. Another press at 20 and it moved halfway - another at 10 and it popped out - hot as hell too I might add - almost as if it had been heated. :) Get this - once the pin cooled down, I tried to push it though the master cylinder - no problem. The only thing holding that pin in place where the plastic bushings - which, despite the heat buildup in the pin from the pressure, were perfectly round. Plastic - hard to believe. So onwards and upwards - new actuator arriving by Thursday and I hope to be back in business with the trailer by Friday. PS: Just in case I missed a spring pin or something, I called UFP, described the problem and asked if there was anything I was missing - nope. I asked if there was a way to move the pins or did they have any suggestions. Use a bigger hammer. Gotta love it. :) |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
The Battle of Trafalgar... | General | |||
THE KANGAROO BATTLE _eq | UK Paddle | |||
The Battle | ASA | |||
BATTLE OF THE GODDESSES! | ASA | |||
Losing the Battle | ASA |