So yesterday we went up to see a boat restorer in upstate NY.
VERY nice guy. Anyway, while talking he reminded me that
I need to run a ground wire from my steel gas tank to the
engine or other ground point. ~ I'm sure this is a good idea
that can't hurt, but I'm just wondering:

#1 - What exactly could happen without that. I assume it's that
a static electric charge could build up on the tank or on me...and
when I touch the gas cap a spark happens in the tank?

#2 - Is the real purpose of the ground to the engine is because
the engine is grounded to the battery or is it because the engine
is connected to the drive shaft which is in the water (true ground).

#3 - What happens when the boat is on the trailer? Then none of
the boat is grounded....It's setting on wooden bunks and on rubber
tires? Couldn't I still get a spark then? ~ It's like a car...that has a
gas tank, but it's not grounded since it all sets on rubber tires?

#4 - Lastly, do the hoses at gas stations connect to ground? The
hoses appear to be rubber but I suppose maybe they are special
hoses with some ground wire embedded in the rubber to take
away any static charge ??

THANKS
Gary

It's been a long time since I have had a gasoline boat, but I do remember
that there was a requirement for a bonding wire in the 'approved' fuel hose
leading from the deck fill to the tank and a bonding from the tank to the
boat bonding system.. Here is the trick. When you install the hose to the
deck fitting and the tank, you are suppose to expose the bonding wire and
fold it back inside the hose so it contacts the metal fittings.

Yes gas pumps have a bonding wire inside their hoses and your are suppose to
make contact with the metal nozzle to the cars metal fill before starting
pumping.

If your filling your boat on a trailer at a gas station, you would discharge
any static by touching the nozzle to the metal fill fitting, same as a car.

Filling with a plastic gas can presents another problem and may be the
reason that some marinas don't allow you to refuel you boat at their slips.

Then there will be those who have argued that they never hear of boat fuel
explosions so it must be ok to fuel from a plastic gas can.. Just not next
to my boat, please.

This summer I heard of a gas station explosion when a lady was fueling her
car, due to static elect. from her clothing.


--
My opinion and experience. FWIW

Steve
s/v Good Intentions

The answer to #4 is that you do have to run a separate ground wire from
the deck fill to ground. It is also a good idea to tap the fuel filler
nozzel against the deck fill before you open it to drain any built up
potential. Aircraft fuel trucks have a separate ground clip that is
attatched to the airplane before fueling to drain any charge.

Gary Warner wrote:

So yesterday we went up to see a boat restorer in upstate NY.
VERY nice guy. Anyway, while talking he reminded me that
I need to run a ground wire from my steel gas tank to the
engine or other ground point. ~ I'm sure this is a good idea
that can't hurt, but I'm just wondering:

#1 - What exactly could happen without that. I assume it's that
a static electric charge could build up on the tank or on me...and
when I touch the gas cap a spark happens in the tank?

#2 - Is the real purpose of the ground to the engine is because
the engine is grounded to the battery or is it because the engine
is connected to the drive shaft which is in the water (true ground).

#3 - What happens when the boat is on the trailer? Then none of
the boat is grounded....It's setting on wooden bunks and on rubber
tires? Couldn't I still get a spark then? ~ It's like a car...that has a
gas tank, but it's not grounded since it all sets on rubber tires?

#4 - Lastly, do the hoses at gas stations connect to ground? The
hoses appear to be rubber but I suppose maybe they are special
hoses with some ground wire embedded in the rubber to take
away any static charge ??

THANKS
Gary






--
Glenn Ashmore

I'm building a 45' cutter in strip/composite. Watch my progress (or lack
there of) at: http://www.rutuonline.com
Shameless Commercial Division: http://www.spade-anchor-us.com

On Thu, 30 Oct 2003 09:55:53 -0500, "Gary Warner"
wrote:


So yesterday we went up to see a boat restorer in upstate NY.
VERY nice guy. Anyway, while talking he reminded me that
I need to run a ground wire from my steel gas tank to the
engine or other ground point. ~ I'm sure this is a good idea
that can't hurt, but I'm just wondering:

#1 - What exactly could happen without that. I assume it's that
a static electric charge could build up on the tank or on me...and
when I touch the gas cap a spark happens in the tank?

BOOOM!

#2 - Is the real purpose of the ground to the engine is because
the engine is grounded to the battery or is it because the engine
is connected to the drive shaft which is in the water (true ground).

Static grounds don't have to handle major lightning strikes, just
provide a leakage path to bleed off the charge before it sparks. The
electrons don't produce BOOOOM!, the heat from the spark does. It's
the heat that sets it off.

#3 - What happens when the boat is on the trailer? Then none of
the boat is grounded....It's setting on wooden bunks and on rubber
tires? Couldn't I still get a spark then? ~ It's like a car...that has a
gas tank, but it's not grounded since it all sets on rubber tires?

Naw....it leaks off quite nicely. My tank is polyethelene in my cheap
Sea Ray. It's just sitting in the bilge, held in with a couple of
little plastic angle brackets and some chewing gum. Polyethelene is
one of the finest insulators we know of. Take a poly bag and shuffle
it across the bed in the dark. It looks like a miniature thunder
storm!

#4 - Lastly, do the hoses at gas stations connect to ground? The
hoses appear to be rubber but I suppose maybe they are special
hoses with some ground wire embedded in the rubber to take
away any static charge ??

Yes, these hoses are CONDUCTIVE back to the grounded pump. Conductive
rubber is used on airplanes for tires for the same reason, to bleed
off static buildup.



Larry W4CSC

"Very funny, Scotty! Now, BEAM ME MY CLOTHES! KIRK OUT!"

Larry W4CSC wrote:


Conductive rubber is used on airplanes for tires for
the same reason, to bleed off static buildup.

Larry, airplane tires are no more or less conductive than nearly any
other vehicle tire.

Do you have a book of wierd technical myths that you drag out every
couple of days or do these ideas just kind of jump off your fingertips
onto the keyboard?

Rick

"Gary Warner" wrote in message
...

#1 - What exactly could happen without that.

If you have a gas guage, the sending unit needs a ground in order to
operate. Since the sending unit frame is "ground" it will connect the tank
to ground at the same time. In many cases, it is the tank that is grounded
and the sending unit gets its ground from the tank.

I assume it's that
a static electric charge could build up on the tank or on me...and
when I touch the gas cap a spark happens in the tank?

Static discharge is a concern, not so much from you and/or fill nozzel but
from the fill plate to the tank. There isn't much you can do to equalize
the charge between the fill nozzel and the boat. As you pointed out, a car
is isolated from ground by the rubber tires. What you can protect against
is a buildup of charge between the fill plate and the tank The fill plate
and tank are generally connected via a rubber hose. If there is no other
electrical connection, it is possible for the gasoline running down the hose
to create a static buildup which create an arc at some point. Running a
ground wire between the two assures that this won't happen.


#2 - Is the real purpose of the ground to the engine is because
the engine is grounded to the battery or is it because the engine
is connected to the drive shaft which is in the water (true ground).

It is a good idea to have a "ground" bonding system that connects everything
together. The engine is usually the common connection point as it offers a
lot of opportunities to make such a connection, plus it is the source of 12
volt power when the engine is running. The battery would be a good spot
except that having too many wires connecting to the battery gets to be a
mess and is a real hassel when you have to change the battery.

There are several reasons why you want everything tied together with an
intended ground bond system. The primary reason is that if you don't
intentionally provide a ground path, you may end up with an unintentional
ground path that could cause problems. This is especially true of any
thru-hull fitting where the unintended ground path could be through the
water and result in electrolysis.

Rod

The only gas gauge on this boat is going to be a stick.

And our filler pipe is a nipple screwed directly to the tank.

But thanks for all the comments anyway...the common ground
ideas apply just fine.

Aircraft hangers generally have ground points to attach the aircraft to.

"Rick" wrote in message
nk.net...
Larry W4CSC wrote:


Conductive rubber is used on airplanes for tires for
the same reason, to bleed off static buildup.

Larry, airplane tires are no more or less conductive than nearly any
other vehicle tire.

Do you have a book of wierd technical myths that you drag out every
couple of days or do these ideas just kind of jump off your fingertips
onto the keyboard?

Rick