Home |
Search |
Today's Posts |
#11
|
|||
|
|||
Roger Long wrote:
Well, the hole in this discussion is already there. Yes, and it seems you don't want it there... or you wouldn't be talking about plugging it up, right? ... The question is how it get's plugged up. It's either going to get plugged up with fiberglass or with the existing bronze fitting designed for this critical service and mechanically locked into the fiberglass by the flange and nut. As someone who has been designing boats (including fiberglass ones) and figuring out how to keep the water out for over a quarter century, I'm in favor of the latter. If cost and time were not issues, and I wanted the inside and outside of the boat to look like nothing was ever there, I would have no qualms about a properly done fiberglass fill in. The issue here is "properly done." If you were talking about a temporary plug, until you are planning to haul the boat later and fiberglass over the hole, I'd say it's fine to put on a cap or a plug. But in the long run, it's still much more vulnerable to corrosion or breakage than a fiberglass patch. Personally I wouldn't haul the boat *just* to do this one job. If that's your point, I'm with you. ... This is a case though where, as an engineering judgement, I think the easy way out is actually the most reliable by a small margin. Why? What is "fiberglassing over the hole" vulnerable to? You still haven't explained that part. And it's certainly not prohibitively expensive... I did exactly that to an unused thru-hull on our boat http://community.webshots.com/photo/...73346002sUSTvu and used probably ten bucks or so worth of stuff... of course I do a fair amount of fiberglass & epoxy work and buy the materials cheaply. Fresh Breezes- Doug King |
#12
|
|||
|
|||
"DSK" wrote in message
.. . Why? What is "fiberglassing over the hole" vulnerable to? You still haven't explained that part. And it's certainly not prohibitively expensive... It's not vulnerable to much unless there is impact and flexing. I wouldn't want to just fill the hole on a solid layup (which my boat is) as there isn't much to hold the patch in. The fiberglass should be tapered back so there is a good, long scarf for bonding. You're right that it wouldn't be expensive to do yourself but I'm thinking yard time (after all, my time is worth something too and unenjoyable jobs like grinding fiberglass don't have their own rewards). By the time it is ground, filled, faired, and re-painted, it will cost a bit either in other things you didn't get done or out of the checkbook. With a cored hull, you can and should dig out as much core as you can reach to seal if from the water. This will create a good mechanical as well as adhesive connection since the patch will extend between the skins. The cap and fill will last as long and reliably (actually more so due to the watertight fill) than the rest of the through hull plumbing. That's good enough for me. Getting plastic through hulls, especially the ones near the waterline that can freeze, replaced with bronze is a much more important issue. -- Roger Long |
#13
|
|||
|
|||
Roger Long wrote:
It's not vulnerable to much unless there is impact and flexing. I'd say even then, it's not any more vulnerable than the rest of the hull, given a proper job. ... I wouldn't want to just fill the hole on a solid layup (which my boat is) as there isn't much to hold the patch in. The fiberglass should be tapered back so there is a good, long scarf for bonding. Sure, that's part of doing it right. I assumed you were comparing the cap/plug to a proper repair, not just slapping in some putty. ... You're right that it wouldn't be expensive to do yourself but I'm thinking yard time (after all, my time is worth something too and unenjoyable jobs like grinding fiberglass don't have their own rewards). By the time it is ground, filled, faired, and re-painted, it will cost a bit either in other things you didn't get done or out of the checkbook. Agreed. But... if the boat is already hauled for other work, and you already have other fiberglass work in hand, doing a patch on a former thru-hull hole is no big deal. I spent more time on the work pictured in putting up & taping a drop cloth in place to keep grinding dust from getting all over the engine room. With a cored hull, you can and should dig out as much core as you can reach to seal if from the water. This will create a good mechanical as well as adhesive connection since the patch will extend between the skins. Agreed. In this case it would be important to make sure the core is thoroughly dry & still bonded, and to use material compatible with the core. Not many hulls are cored below the waterline though AFAIK. The cap and fill will last as long and reliably (actually more so due to the watertight fill) than the rest of the through hull plumbing. Sure, but that's the point. A thru-hull is a vulnerable point. It's a hole in the hull, a potentially disasterous leak. Vulnerable to grounding or other impact, flexing, corrosion, freezing, electrolysis, and occasional misadventures. As opposed to a hole that has been fiberglassed over, which is vulnerable to... umm, you haven't explained that part yet... That's good enough for me. Getting plastic through hulls, especially the ones near the waterline that can freeze, replaced with bronze is a much more important issue. If that's already on your work schedule, then removing & fiberglassing over the old unused thru-hull during the same haul-out is a trivial addition IMHO. But hey it's your boat Fresh Breezes- Doug King |
#14
|
|||
|
|||
Ken,
I'll be bringing my boat up to Cape Breton this Summer and would appreciate your recommendations regarding suppliers of necessaries/desirables for sailboats in the area, as I'll be doing a lengthy refitting and am unfamiliar with suppliers beyond Port Hawkesbury, though please don't omit recommendations there either. On the other hand if you've discovered better sources outside of Cape Breton, please send them on :-) Appreciatively, Courtney Ken Heaton wrote: Here is one source: http://www.stright-mackay.com/pages/...5&CategoryID=5 http://www.stright-mackay.com/ -- s/v Mutiny Rhodes Bounty II lying Oriental, NC WDB5619 |
#15
|
|||
|
|||
Hi Courtney,
Port Hawkesbury is about two hours away by car so I don't buy much there. Most of the suppliers in Cape Breton service the commercial fishing fleets and other commercial users but some deal with recreational boaters as well, such as Sydney Ship Supply (now owned by the IMP Group of companies): P.O. Box 38 Victoria Road Sydney, NS B1N 3B1 Tel: (902) 564-5425 Fax: (902) 539-0904 http://www.impmarine.com/impmarine/ I'd probably be more helpful if you had a specific request for an item or service. We search for many things online. I used to have all sorts of links collected together somewhere but I can't find them anymore. Here a short list of online suppliers in Nova Scotia and beyond: These guys are based in Halifax, NS: http://ca.binnacle.com/online/ As a http://www.mmosonline.com/ I've dealt with both, both online and by calling or visiting their stores, and am happy with the service. In Toronto: http://www.hollandmarine.com/ The next two have a somewhat limited online presence but offer used equipment. Based in Sidney, BC: http://www.theboatersexchange.com/ or Vancouver: http://www.marinersxchange.com/ "Courtney Thomas" wrote in message ... Ken, I'll be bringing my boat up to Cape Breton this Summer and would appreciate your recommendations regarding suppliers of necessaries/desirables for sailboats in the area, as I'll be doing a lengthy refitting and am unfamiliar with suppliers beyond Port Hawkesbury, though please don't omit recommendations there either. On the other hand if you've discovered better sources outside of Cape Breton, please send them on :-) Appreciatively, Courtney Ken Heaton wrote: Here is one source: http://www.stright-mackay.com/pages/...5&CategoryID=5 http://www.stright-mackay.com/ -- s/v Mutiny Rhodes Bounty II lying Oriental, NC WDB5619 |
Reply |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Hull Design & Displacement Hulls | General | |||
Through hulls and seacocks | Cruising | |||
cored hulls | General | |||
Sanding plastic hulls | Touring | |||
Balsa core hulls & Sea Rays | General |