Loctite for bolts
 

Brian Nystrom wrote:

Well, I guess they're simpler and more durable if the fasteners are
disassembled multiple times. Other than that, I don't think there is any
advantage. Nyloc nuts are definitely much more expensive, bulkier
and heavier than regular nuts and Loctite.


Also, Nylocks should not be trusted if removed more than once or twice.
If something is that critical and needs to be removed often, castle
nuts and safety wire are the ultimate solution.

--
Glenn Ashmore

I'm building a 45' cutter in strip/composite. Watch my progress (or lack
there of) at: http://www.rutuonline.com
Shameless Commercial Division: http://www.spade-anchor-us.com

Loctite for bolts
 

Ok Adam,
Are you thoroughly confused yet? Back to the original
question............you can use loctite, however, in my 22+ years in the
U.S.Navy, it has been my experience that nyloc coupled to SS nuts and bolts
is a beautiful thing. There is no mess to clean up, the additional cost and
weight are minimal at worst, and best of all no corrosion to worry about at
all. The nyloc is injected into a hole drilled into the side of the bolt
during the mfr process. On the nut, there is a lip added during the molding,
which is filled with nylon. You buy them, you screw them together, tighten
and forget them. They will not loosen over time, degrade or be impossible
for future removal (if you ever need it). In short, the additional few cents
per nut and bolt is excellent peace of mind down the road. For the rest of
you well meaning lads.....I recommend "Screw loose" by CRC.
Joe



"Adam" wrote in message
...
I'm going to install floor stiffeners (2"x4" cedar sealed 3x by S1 -
floors
are 1/2" marine plywood sealed as well) using machine SS bolts 3/8" 3", 4"
&
5" long.
Should I use any of Lctie for the nuts?
Thanks in advance
Adam

Loctite for bolts
 

OK but not on hot engine parts

Brian W

On Sat, 15 May 2004 07:47:23 -0400, "JSE" wrote:

Ok Adam,
Are you thoroughly confused yet? Back to the original
question............you can use loctite, however, in my 22+ years in the
U.S.Navy, it has been my experience that nyloc coupled to SS nuts and bolts
is a beautiful thing. There is no mess to clean up, the additional cost and
weight are minimal at worst, and best of all no corrosion to worry about at
all. The nyloc is injected into a hole drilled into the side of the bolt
during the mfr process. On the nut, there is a lip added during the molding,
which is filled with nylon. You buy them, you screw them together, tighten
and forget them. They will not loosen over time, degrade or be impossible
for future removal (if you ever need it). In short, the additional few cents
per nut and bolt is excellent peace of mind down the road. For the rest of
you well meaning lads.....I recommend "Screw loose" by CRC.
Joe



"Adam" wrote in message
...
I'm going to install floor stiffeners (2"x4" cedar sealed 3x by S1 -
floors
are 1/2" marine plywood sealed as well) using machine SS bolts 3/8" 3", 4"
&
5" long.
Should I use any of Lctie for the nuts?
Thanks in advance
Adam

Loctite for bolts
 

Thanks Joe;
You are right - totally confused. As always, common sense, and the true is
still somewhere in between.
For floor and stiffeners I will use loctite. For other application like deck
shelf I will go with nyloc.
Once again
Thanks you
Adam
"JSE" wrote in message ...
Ok Adam,
Are you thoroughly confused yet? Back to the original
question............you can use loctite, however, in my 22+ years in the
U.S.Navy, it has been my experience that nyloc coupled to SS nuts and
bolts
is a beautiful thing. There is no mess to clean up, the additional cost
and
weight are minimal at worst, and best of all no corrosion to worry about
at
all. The nyloc is injected into a hole drilled into the side of the bolt
during the mfr process. On the nut, there is a lip added during the
molding,
which is filled with nylon. You buy them, you screw them together, tighten
and forget them. They will not loosen over time, degrade or be impossible
for future removal (if you ever need it). In short, the additional few
cents
per nut and bolt is excellent peace of mind down the road. For the rest of
you well meaning lads.....I recommend "Screw loose" by CRC.
Joe



"Adam" wrote in message
...
I'm going to install floor stiffeners (2"x4" cedar sealed 3x by S1 -
floors
are 1/2" marine plywood sealed as well) using machine SS bolts 3/8" 3",
4"
&
5" long.
Should I use any of Lctie for the nuts?
Thanks in advance
Adam

Loctite for bolts
 

Glad to help...happy sailing.....or as we say in the Navy " Fair Winds and
Following Seas"
Joe



"Adam" wrote in message
...
Thanks Joe;
You are right - totally confused. As always, common sense, and the true is
still somewhere in between.
For floor and stiffeners I will use loctite. For other application like
deck
shelf I will go with nyloc.
Once again
Thanks you
Adam
"JSE" wrote in message ...
Ok Adam,
Are you thoroughly confused yet? Back to the original
question............you can use loctite, however, in my 22+ years in the
U.S.Navy, it has been my experience that nyloc coupled to SS nuts and
bolts
is a beautiful thing. There is no mess to clean up, the additional cost
and
weight are minimal at worst, and best of all no corrosion to worry about
at
all. The nyloc is injected into a hole drilled into the side of the bolt
during the mfr process. On the nut, there is a lip added during the
molding,
which is filled with nylon. You buy them, you screw them together,
tighten
and forget them. They will not loosen over time, degrade or be
impossible
for future removal (if you ever need it). In short, the additional few
cents
per nut and bolt is excellent peace of mind down the road. For the rest
of
you well meaning lads.....I recommend "Screw loose" by CRC.
Joe



"Adam" wrote in message
...
I'm going to install floor stiffeners (2"x4" cedar sealed 3x by S1 -
floors
are 1/2" marine plywood sealed as well) using machine SS bolts 3/8"
3",
4"
&
5" long.
Should I use any of Lctie for the nuts?
Thanks in advance
Adam