Home |
Search |
Today's Posts |
#1
|
|||
|
|||
sectional or bolt together boats
On Tue, 9 Sep 2003 22:24:36 -0500, "Wayne" wrote:
the "chameleon" dinghy by danny green, c/o offshore designs ltd., p.o.box ge213, st.george's, bermuda ge bx. it is a brillant design, we built one and have seen rowed three others in various states of finish. check our boat building skills out at wwwsailorgirl.com I don't see the whole thread of this message so this may have been discussed but take a look at the FB11 in the small boats secton of www.bateau.com . k.t.h wrote: Hi, due to space and access dificulties I'm trying to find information on building a sectional, bolt together, boat. SNIP I'm thinking of something like a 14 foot dinghy built in two sections but an open canoe or anything is ok, I don't intend use in heavy seas but being confident it will hold together in a bit of chop would be nice. Primary use is with small 2-3hp outboard but easy rowing would be nice. |
#3
|
|||
|
|||
sectional or bolt together boats
wrote: On Tue, 9 Sep 2003 22:24:36 -0500, "Wayne" wrote: the "chameleon" dinghy by danny green, c/o offshore designs ltd., p.o.box ge213, st.george's, bermuda ge bx. it is a brillant design, we built one and have seen rowed three others in various states of finish. check our boat building skills out at wwwsailorgirl.com Can someone explain the advantages of the Danny Green dinghy over the Gerr dinghy? I will have to admit that the Gerr clamps take a lot of work to fabricate but they sure make putting the boat together in the water a lot easier. Looking at the pictures they apear to be very similar designs but I would think that those flotation chambers add a lot of pounds. I built a Gerr dink and it came in at 104 pounds. I am playing with an idea to build a slightly modified version in cedar strip that should come in around 75 pounds. -- Glenn Ashmore I'm building a 45' cutter in strip/composite. Watch my progress (or lack there of) at: http://www.rutuonline.com Shameless Commercial Division: http://www.spade-anchor-us.com |
#4
|
|||
|
|||
sectional or bolt together boats
You've built one, while I've just looked hard at building one, so
you're miles ahead. Hands on experience beats analysis any day. With that said: 1) I don't like left hand threads. I understand what he wants to do -- put the clamp on with a normal, clockwise, forward motion, but I think it's easier for the user to recognize that he wants to move the rod toward himself and turn it accordingly. This is particularly true if you're leaning over from the other half while doing it. 2) I don't like left hand threads. It cuts down on your choice of off the shelf materials. Not much, though, as you could use a silicon bronze acme nut and 18-8 SS rod. (Running 18-8 threads in 18-8 nuts is a bad idea as it tend to gall, but the 18-8/silicon bronze combination used to be common in turnbuckles -- now we just put up with the occasional galling of a modern all SS turnbuckle) 3) I don't think they're beefy enough. 1/2" rod will bend when someone stands on them. And I would use an acme thread. 4) I don't like the mount of the attaching plate (The plate with the keyhole). The clamp will tend to pull it away from its hull. It only has to pull away (or bend) a little and you have a gap between hulls. I would prefer a longer clamp screw and the attaching plate on the inside of the other hull. This will complicate watertightness, but it's worth it. 5) I would through bolt the clamp plate. Never wood screw anything under load. 6) I'm suspicious of the end of the clamp. You're pulling against the weld, which is a weak spot. Another reason to go up in size and switch the clamp screw to 18-8. 7) The 3/16" clamp levers will be bent in no time. And, finally, nesting dinghys are over-rated for the voyager. We had an Avon 3.15 rollup and a beautiful 12' rowing/sailing dinghy on our circumnav. The Avon did all the work -- stable, dry, non marring, fast (with nine hp) to shore which was as much as a mile away. Easy to beach and to mount wheels to take it above the tide (1/4 mile in Darwin). The hard dinghy was a joy to row or sail, but was strictly a toy. Rubber duckies owned the voyaging market then and, I'm sure, now. Jim Woodward www.mvFintry.com Glenn Ashmore wrote in message news:wRwnb.106439$sp2.38934@lakeread04... wrote: On Tue, 9 Sep 2003 22:24:36 -0500, "Wayne" wrote: the "chameleon" dinghy by danny green, c/o offshore designs ltd., p.o.box ge213, st.george's, bermuda ge bx. it is a brillant design, we built one and have seen rowed three others in various states of finish. check our boat building skills out at wwwsailorgirl.com Can someone explain the advantages of the Danny Green dinghy over the Gerr dinghy? I will have to admit that the Gerr clamps take a lot of work to fabricate but they sure make putting the boat together in the water a lot easier. Looking at the pictures they apear to be very similar designs but I would think that those flotation chambers add a lot of pounds. I built a Gerr dink and it came in at 104 pounds. I am playing with an idea to build a slightly modified version in cedar strip that should come in around 75 pounds. |
#5
|
|||
|
|||
sectional or bolt together boats
Jim Woodward wrote: You've built one, while I've just looked hard at building one, so you're miles ahead. Hands on experience beats analysis any day. With that said: 1) I don't like left hand threads. I understand what he wants to do -- put the clamp on with a normal, clockwise, forward motion, but I think it's easier for the user to recognize that he wants to move the rod toward himself and turn it accordingly. This is particularly true if you're leaning over from the other half while doing it. In an attempt to use off the shelf parts I built a test clamp using standard RH threaded rod but there is something instinctive about tightening anything from bolts to bottle caps clockwise. After I noticed the problem I tried a mock up with a couple of boards on several people. Everyone was confused by the RH thread. 2) I don't like left hand threads. It cuts down on your choice of off the shelf materials. Not much, though, as you could use a silicon bronze acme nut and 18-8 SS rod. (Running 18-8 threads in 18-8 nuts is a bad idea as it tend to gall, but the 18-8/silicon bronze combination used to be common in turnbuckles -- now we just put up with the occasional galling of a modern all SS turnbuckle) I turned LH Acme threads on the rods. Not hard to do and you have a little smooth rod out at the handle end so you don't scratch your fingers. Also turned a tapered spigot on the clamping end to align the washer. The only down side was that the LH acme tap for the clamp plate cost $90 but I have used it several times for other things. 3) I don't think they're beefy enough. 1/2" rod will bend when someone stands on them. And I would use an acme thread. That is really a non issue. The bolt is in almost 100% tension and only protrudes 2". Someone would have to jump up and down on the handle to bend it. 4) I don't like the mount of the attaching plate (The plate with the keyhole). The clamp will tend to pull it away from its hull. It only has to pull away (or bend) a little and you have a gap between hulls. I would prefer a longer clamp screw and the attaching plate on the inside of the other hull. This will complicate watertightness, but it's worth it. The Keyhole plate is through bolted with 1/2" FH bolts with a 1/16" backing plate on the other side. It will not move very far without ripping out the bulkhead. 5) I would through bolt the clamp plate. Never wood screw anything under load. The clamp plate is being pressed into the bulkhead when under load. The screws are there just to hold it in place when it is not being used. 6) I'm suspicious of the end of the clamp. You're pulling against the weld, which is a weak spot. Another reason to go up in size and switch the clamp screw to 18-8. Actually if properly done with 1/8" thick washers and a short spigot on the end of the bolt the weld will be in shear rather than tension. The whole design will be much stronger than bolts and wing nuts used on most designs I have seen. I did change to 17-4PH rather than 316 for the bolts. 17-4 is much easier to machine and is about twice as strong as 316. Same corrosion resistance as Nitronic 50. 7) The 3/16" clamp levers will be bent in no time. Now that is a possibility but your hand will be hurting long before the lever bends. The real disadvantage of the Gerr clamp is the setup time on the mill and lathe. The first clamp cost about $400 but you can knock out the rest for under $20 each. And, finally, nesting dinghys are over-rated for the voyager. We had an Avon 3.15 rollup and a beautiful 12' rowing/sailing dinghy on our circumnav. The Avon did all the work -- stable, dry, non marring, fast (with nine hp) to shore which was as much as a mile away. Easy to beach and to mount wheels to take it above the tide (1/4 mile in Darwin). The hard dinghy was a joy to row or sail, but was strictly a toy. Rubber duckies owned the voyaging market then and, I'm sure, now. That is more of a philosophical question. It depends on your preferences. The nesting dink will get in the water faster than a deflated roll up and for the more organic oriented rows much better. Also the cost of a DIY nester and a nice pair of Shaw & Tenneys is about half that of a roll up and motor. For those of us who will run out of boat bucks just about the time the mother ship is launched that is a very attractive feature. :-) -- Glenn Ashmore I'm building a 45' cutter in strip/composite. Watch my progress (or lack there of) at: http://www.rutuonline.com Shameless Commercial Division: http://www.spade-anchor-us.com |
#6
|
|||
|
|||
sectional or bolt together boats
As I said -- you've built one -- the voice of experience is always
clearer than the voice of analysis. But: #2 Wouldn't it have been easier and cheaper to buy a silicon bronze left hand acme nut from our favorite supply house? #4 Apparently you agreed with me, as the drawing shows 1/4" bolts and you used 1/2". #5 Right. I should have noticed that. #6 Also, you apparently agreed with me -- he calls out bronze and you switched to 17-4PH. As to the philosophical question -- I love rowing or sailing our twelve footer -- it's a real pleasure -- probably more so than your Nester, as it's a no compromise boat. But on a daily basis, getting in and out of a hard dinghy is a pain. Getting into one with SCUBA gear on is almost impossible. It's one thing to love a hard dinghy when you use it a few times in sheltered places; quite another when you use it daily in relatively unsheltered anchorages where the mother ship is moving up and down and the dinghy is also dancing, to a different drummer, and you can't step on the gunwhale. And rowing a mile to weather (15-20 knots) in Darwin in the morning and then a mile back, also to weather, in the evening (wind seemed to shift every day) would have been a real trial. Of course Darwin's a worst case, but there were many places where the dinghy dock was half a mile from our anchor. Jim Woodward www.mvFintry.com Glenn Ashmore wrote in message news:JzPnb.106768$sp2.24480@lakeread04... Jim Woodward wrote: You've built one, while I've just looked hard at building one, so you're miles ahead. Hands on experience beats analysis any day. With that said: 1) I don't like left hand threads. I understand what he wants to do -- put the clamp on with a normal, clockwise, forward motion, but I think it's easier for the user to recognize that he wants to move the rod toward himself and turn it accordingly. This is particularly true if you're leaning over from the other half while doing it. In an attempt to use off the shelf parts I built a test clamp using standard RH threaded rod but there is something instinctive about tightening anything from bolts to bottle caps clockwise. After I noticed the problem I tried a mock up with a couple of boards on several people. Everyone was confused by the RH thread. 2) I don't like left hand threads. It cuts down on your choice of off the shelf materials. Not much, though, as you could use a silicon bronze acme nut and 18-8 SS rod. (Running 18-8 threads in 18-8 nuts is a bad idea as it tend to gall, but the 18-8/silicon bronze combination used to be common in turnbuckles -- now we just put up with the occasional galling of a modern all SS turnbuckle) I turned LH Acme threads on the rods. Not hard to do and you have a little smooth rod out at the handle end so you don't scratch your fingers. Also turned a tapered spigot on the clamping end to align the washer. The only down side was that the LH acme tap for the clamp plate cost $90 but I have used it several times for other things. 3) I don't think they're beefy enough. 1/2" rod will bend when someone stands on them. And I would use an acme thread. That is really a non issue. The bolt is in almost 100% tension and only protrudes 2". Someone would have to jump up and down on the handle to bend it. 4) I don't like the mount of the attaching plate (The plate with the keyhole). The clamp will tend to pull it away from its hull. It only has to pull away (or bend) a little and you have a gap between hulls. I would prefer a longer clamp screw and the attaching plate on the inside of the other hull. This will complicate watertightness, but it's worth it. The Keyhole plate is through bolted with 1/2" FH bolts with a 1/16" backing plate on the other side. It will not move very far without ripping out the bulkhead. 5) I would through bolt the clamp plate. Never wood screw anything under load. The clamp plate is being pressed into the bulkhead when under load. The screws are there just to hold it in place when it is not being used. 6) I'm suspicious of the end of the clamp. You're pulling against the weld, which is a weak spot. Another reason to go up in size and switch the clamp screw to 18-8. Actually if properly done with 1/8" thick washers and a short spigot on the end of the bolt the weld will be in shear rather than tension. The whole design will be much stronger than bolts and wing nuts used on most designs I have seen. I did change to 17-4PH rather than 316 for the bolts. 17-4 is much easier to machine and is about twice as strong as 316. Same corrosion resistance as Nitronic 50. 7) The 3/16" clamp levers will be bent in no time. Now that is a possibility but your hand will be hurting long before the lever bends. The real disadvantage of the Gerr clamp is the setup time on the mill and lathe. The first clamp cost about $400 but you can knock out the rest for under $20 each. And, finally, nesting dinghys are over-rated for the voyager. We had an Avon 3.15 rollup and a beautiful 12' rowing/sailing dinghy on our circumnav. The Avon did all the work -- stable, dry, non marring, fast (with nine hp) to shore which was as much as a mile away. Easy to beach and to mount wheels to take it above the tide (1/4 mile in Darwin). The hard dinghy was a joy to row or sail, but was strictly a toy. Rubber duckies owned the voyaging market then and, I'm sure, now. That is more of a philosophical question. It depends on your preferences. The nesting dink will get in the water faster than a deflated roll up and for the more organic oriented rows much better. Also the cost of a DIY nester and a nice pair of Shaw & Tenneys is about half that of a roll up and motor. For those of us who will run out of boat bucks just about the time the mother ship is launched that is a very attractive feature. :-) |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
VEC build techniques to become more prevalent | General | |||
Sea Ray Boats, Mid-Atlantic Dealers Announce Post-Hurricane Recovery Initiatives | General | |||
Any information on sectional or bolt together boats | Boat Building | |||
Is sailing becoming extinct? | General | |||
Marina fire destroys 25 boats near Orlando | General |