Nah, the B&D sander/polisher. I just sold some 'junk' on ebay for $320.

Scotty


"Capt. Mooron" wrote in message
news

"Scott Vernon" wrote in message

| Buffed and waxed the hull, but need to do it over again.

Did you use your Industrial Grade Grinder to polish it??

Maybe you can find one on Ebay. ;-D

CM

Jon, what did the cover cost? You can email me if you want.

Scotty

"Jonathan Ganz" wrote in message
...
Nothing that much. Had a diver clean off the bottom. Also,
just got a mailsail cover made. The guy who sewed it for
me, didn't get the length right, but he's redoing it. Should
be ready in a day or two.

http://www.sailnow.com/gifs/mainsail1.jpg

--
"j" ganz @@
www.sailnow.com

OzOne wrote in message
...
On 23 Apr 2004 19:25:22 -0700, (N1EE)
scribbled thusly:



3. The best sander to use is a 6" orbital hook and loop
--6 hole hook and loop--60-80 grit paper. I also used an
air powered longboards for final sanding--use 80-100 grit.

Beg to differ, but the BEST sander to use is the Powerboard
http://www.atlcomposites.com/product...powerboard.htm

You'll be astounded at just how fast you get the job done


Oz1...of the 3 twins.

I welcome you to crackerbox palace,We've been expecting you.

"Horvath" wrote

Install new, bigger holding tank.

Now there's a load of crap.


No, really, I did....honest.



Made a new mount for the bow red/green light. Someone broke it off at my
slip.

Those *******s!


Yeah, I'm sure it was a power boat.


New ign. switch for the Yanmar.
Maintenance. Boring.


new switch is not maintenance. It's a three pole switch off a motorcycle.
I wired it so I can start the engine ( or check the fuel gauge) without
that damn buzzer going off.

Scotty

Horass, stupid.

--
"j" ganz @@
www.sailnow.com

"Horvath" wrote in message
...
On Fri, 23 Apr 2004 23:25:51 -0400, "Scott Vernon"
wrote this crap:

Install new, bigger holding tank.

Now there's a load of crap.

Made a new mount for the bow red/green light. Someone broke it off at my
slip.

Those *******s!

New ign. switch for the Yanmar.
replaced water pump impellor.
Oiled and re-routed the engine shut-off cable.
New packing in stuffing box.
Touched up bottom paint.
Buffed and waxed the hull, but need to do it over again.

Maintenance. Boring.




My T-shirt says, "This shirt is the
ultimate power in the universe."

The material was $40 on ebay. He charged me $100 for the labor.

--
"j" ganz @@
www.sailnow.com

"Scott Vernon" wrote in message
...
Jon, what did the cover cost? You can email me if you want.

Scotty

"Jonathan Ganz" wrote in message
...
Nothing that much. Had a diver clean off the bottom. Also,
just got a mailsail cover made. The guy who sewed it for
me, didn't get the length right, but he's redoing it. Should
be ready in a day or two.

http://www.sailnow.com/gifs/mainsail1.jpg

--
"j" ganz @@
www.sailnow.com

OzOne wrote in message
...
On 23 Apr 2004 19:25:22 -0700, (N1EE)
scribbled thusly:



3. The best sander to use is a 6" orbital hook and loop
--6 hole hook and loop--60-80 grit paper. I also used an
air powered longboards for final sanding--use 80-100 grit.

Beg to differ, but the BEST sander to use is the Powerboard
http://www.atlcomposites.com/product...powerboard.htm

You'll be astounded at just how fast you get the job done


Oz1...of the 3 twins.

I welcome you to crackerbox palace,We've been expecting you.

But you clearly like to be beaten. That's why you keep coming back
here. Won some more fags, I mean flags? Wow. Ok. Too much info
for most of us I'm sure.

--
"j" ganz @@
www.sailnow.com

"Horvath" wrote in message
...
On 23 Apr 2004 19:25:22 -0700, (N1EE) wrote
this crap:

Your spring project reports are due soon. (10 pts)

What sort of projects have you been doing to
improve your boat? Report in, or take a dozen
lashes!

No. Please don't beat me!

I had my crew put on a folding prop. I had my crew secretly modify
the keel.

My report: Hull Fairing and Painting Project

The last few weeks I've been fairing the hull of my
big boat with a goal of getting it in the water by May
30th.


You must be kidding! By Memorial Day, I will have won several series
of races.


I've just about completed the bottom of the hull,
and plan one more layup of fairing material on the hull.
So far I must have over 24 hours of sanding, and my
brother has another 16 hours logged.


Boring! You call that improvements? I call it maintenance.

[all other boring crap deleted]


I want to hear about improvements, not about how you changed your oil.





My T-shirt says, "This shirt is the
ultimate power in the universe."

OK, thanks. I'm thinking about doing canvas work when I retire.

SV


"Jonathan Ganz" wrote in message
...
The material was $40 on ebay. He charged me $100 for the labor.

--
"j" ganz @@
www.sailnow.com

"Scott Vernon" wrote in message
...
Jon, what did the cover cost? You can email me if you want.

Scotty

"Jonathan Ganz" wrote in message
...
Nothing that much. Had a diver clean off the bottom. Also,
just got a mailsail cover made. The guy who sewed it for
me, didn't get the length right, but he's redoing it. Should
be ready in a day or two.

http://www.sailnow.com/gifs/mainsail1.jpg

--
"j" ganz @@
www.sailnow.com

OzOne wrote in message
...
On 23 Apr 2004 19:25:22 -0700, (N1EE)
scribbled thusly:



3. The best sander to use is a 6" orbital hook and loop
--6 hole hook and loop--60-80 grit paper. I also used an
air powered longboards for final sanding--use 80-100 grit.

Beg to differ, but the BEST sander to use is the Powerboard
http://www.atlcomposites.com/product...powerboard.htm

You'll be astounded at just how fast you get the job done


Oz1...of the 3 twins.

I welcome you to crackerbox palace,We've been expecting you.

I take it then that you totally ignored Bob's adamant advise that an
Industrial Grade Grinder with a polishing pad is the ultimate tool for a
mirror like finish on your hull????

Well... off I go to buy a set of motorized router bits. I think I'll take my
Mountain Bike and make sure I drive back and forth in front of the store's
driveway just to be sure I'm at the right place. ;-)

Of course I'll tell everyone I went to the other side of town and not the
local outlet.

I'll also mentioned I raced & passed a Vette along the way......

CM


"Scott Vernon" wrote in message
...
| Nah, the B&D sander/polisher. I just sold some 'junk' on ebay for $320.
|
| Scotty
|
|
| "Capt. Mooron" wrote in message
| news |
| "Scott Vernon" wrote in message
|
| | Buffed and waxed the hull, but need to do it over again.
|
| Did you use your Industrial Grade Grinder to polish it??
|
| Maybe you can find one on Ebay. ;-D
|
| CM
|
|
|

"Capt. Mooron" wrote ...
I take it then that you totally ignored Bob

I try to.

Motorized router bits? You guys have some weird
stuff up there in Canada.
S

"Capt. Mooron" wrote in
message
news : I take it then that you totally ignored Bob's
adamant advise that an
: Industrial Grade Grinder with a polishing pad is
the ultimate tool for a
: mirror like finish on your hull????
:
: Well... off I go to buy a set of motorized
router bits. I think I'll take my
: Mountain Bike and make sure I drive back and
forth in front of the store's
: driveway just to be sure I'm at the right place.
;-)
:
: Of course I'll tell everyone I went to the other
side of town and not the
: local outlet.
:
: I'll also mentioned I raced & passed a Vette
along the way......
:
: CM
:
:
: "Scott Vernon" wrote in
message
:
...
: | Nah, the B&D sander/polisher. I just sold
some 'junk' on ebay for $320.
: |
: | Scotty
: |
: |
: | "Capt. Mooron" wrote in
message
: | news : |
: | "Scott Vernon" wrote in
message
: |
: | | Buffed and waxed the hull, but need to do
it over again.
: |
: | Did you use your Industrial Grade Grinder to
polish it??
: |
: | Maybe you can find one on Ebay. ;-D
: |
: | CM
: |
: |
: |
:
: