Thanks Jim!

What exactly are exhaust shutters?

"JIMinFL" wrote in message
ink.net...
It's time to change the risers on a 10 yr old boat. Replace the exhaust
shutters too. Total job less than $400 if you do it yourself.You have done
all you can do. Just keep your fingers crossed and put on as many hours as
you can for the rest of the season to work out any salt that might be
stuck
in the ring grooves. Change the oil again during layup.
JIMinFL

--

"Ed" wrote in message
news
The problem appears to have been caused by water ingestion. I pulled the
plugs and the engine blew out quite a bit of water.

I put new plugs in, and the engine started right up!

Now my question is, what else do I do?

I changed the plugs, and I am in the process of changing the engine oil
and
filter, but what else should I do to stop any additional corrosion?

Thanks for all those who helped!

Ed.


"Ed" wrote in message news:...
Thanks!

I tried to turn the engine over but I only had a normal 3/8" drive
ratchet
and I was only able to turn it an eight of a turn before the bolt
loosened-
I'll go back this weekend to check it out (The boat is stored at the
Marina).

I don't think there is water in the engine (or hope!), as there was
very
little water in the bilge, and the boat was run all weekend in calm
seas-
I
really just don't want it to be an engine problem......


"JamesgangNC" wrote in message
nk.net...
That sounds a lot more like an engine problem than an outdrive. The
possibility that your outdrive or a ujoint would break while cranking
are
pretty low. And if a ujoint borke I would not expect it to stop the
engine
from turning. Start by putting a long breaker bar on the front of
the
crack
and see if you can turn the engine by hand. You need a 5/8 socket.
You
may
be able to turn it backward with the breaker bar. If the center bolt
starts
backing out then thread a couple 2 to 3 inch 3/8 bolts into the
balancer
to
rest the breaker bar against. There are three bolt holes in the
balancer,
there may be short bolts in them but you can take one or two of these
out
temporarily. If it turns over freely then I'd check the starter
before
anything else. If it won't turn over either way then pull the plugs
and
try
again. Check the ends of the plugs for damage.

One of the problems with your symptoms is water getting into one or
more
cylinders. Either because of a bad manifold/riser or simply because
of
a
shot flapper and a few good sized waves into the transom. If water
gets
into a cylinder and the engine cranks, the water can not compress.
Sometimes the result is a broken rod. Particularly if the engine
gets
a
chance to start as then it really has some power behind that piston
when
it
comes up on the compression stroke. If the engine doesn't start the
water
will usually just stop the starter in its tracks, the starter is not
strong
enough to break a rod. Broken rods ends often jam into the block and
prevent the engine form turning any further. This is the worst case
scenario so eliminate everything else first.

"Ed" wrote in message
ink.net...
Hi All-

Before I decide to tear open the outdrive, I thought I would check
to
see
if
there are any ideas as to the cause of my problem.

I was down on the coast this past weekend (in NC) for some great
boating
and
as usual when I return from the coast, I take the boat to a fresh
water
lake
to run all the sal****er out of the system. When I attempted to
start
the
engine it turned over maybe one or two revolutions and then a
terrible
sounding 'clank' occurred and then it seems that the
engine/outdrive
was
seized. The boat ran flawlessly the entire weekend prior to the
failure,
so
I don't believe the engine itself is seized.

Does this sound like a broken U-joint or lower unit gear problem?
The
gear
shift lever seems to function normally.

Any advice would be appreciated!

Ed