Ok i bought the boat with 5.7 mercruiser 1990 350 cdi . It has water
oil mix on the oil stik and it is not starting where shuld I start
looking. I did notice small water driping on the sides of manifolds

On Thu, 28 Aug 2008 08:40:23 -0700 (PDT), wrote:

Ok i bought the boat with 5.7 mercruiser 1990 350 cdi . It has water
oil mix on the oil stik and it is not starting where shuld I start
looking. I did notice small water driping on the sides of manifolds

My brother had the same thing happen - it was head gaskets, but he
changed the heads and gaskets at the same time.

"Short Wave Sportfishing" wrote in message
...
On Thu, 28 Aug 2008 08:40:23 -0700 (PDT), wrote:

Ok i bought the boat with 5.7 mercruiser 1990 350 cdi . It has water
oil mix on the oil stik and it is not starting where shuld I start
looking. I did notice small water driping on the sides of manifolds

My brother had the same thing happen - it was head gaskets, but he
changed the heads and gaskets at the same time.

If it overheated the heads warp on a Chevy. But since manifolds are
dripping, I would check for a hole in the exhaust manifolds.

wrote in message
...
Ok i bought the boat with 5.7 mercruiser 1990 350 cdi . It has water
oil mix on the oil stik and it is not starting where shuld I start
looking. I did notice small water driping on the sides of manifolds

Besides bad head gaskets there are a couple other common causes of this on
boats. If it has not run since winter and you are in a climate that has
freezing weather it could be a cracked block. Small blocks are pretty weak
on the inside of the block adjacent to the valve push rods. If the exhaust
manifolds are old they may be leaking into the cylinders. Then the sitting
water in the cylinder(s) will make it's way down past the rings into the
oil.

On Aug 28, 10:40*am, wrote:
Ok i bought the boat with 5.7 mercruiser 1990 350 cdi . It has water
oil mix on the oil stik and it is not starting where shuld I start
looking. *I did notice small water driping on the sides of manifolds

Today I removed intake and find out that the head is cracked. I will
take apart the rest of the engine and check if anything els is bad .
Do you guys know where can I buy used parts for 5.7 V8 1990 350 cdi

wrote in message
...
On Aug 28, 10:40 am, wrote:
Ok i bought the boat with 5.7 mercruiser 1990 350 cdi . It has water
oil mix on the oil stik and it is not starting where shuld I start
looking. I did notice small water driping on the sides of manifolds

Today I removed intake and find out that the head is cracked. I will
take apart the rest of the engine and check if anything els is bad .
Do you guys know where can I buy used parts for 5.7 V8 1990 350 cdi

Any wrecking yard. Take the head with you so you can get a matching head.

On Aug 30, 12:42*am, "CalifBill" wrote:
wrote in message

...
On Aug 28, 10:40 am, wrote:

Ok i bought the boat with 5.7 mercruiser 1990 350 cdi . It has water
oil mix on the oil stik and it is not starting where shuld I start
looking. I did notice small water driping on the sides of manifolds

Today I removed intake and find out that the head is cracked. I will
take apart the rest of the engine and check if anything els is bad .
Do you guys know where can I buy used parts for *5.7 V8 1990 350 cdi

Any wrecking yard. *Take the head with you so you can get a matching head.

Can you please tell me if is going to fit from GM cars and wich
ones . What do I have to look for when I'm maching them

On Aug 30, 1:09*am, wrote:
On Aug 30, 12:42*am, "CalifBill" wrote:

wrote in message

...
On Aug 28, 10:40 am, wrote:

Ok i bought the boat with 5.7 mercruiser 1990 350 cdi . It has water
oil mix on the oil stik and it is not starting where shuld I start
looking. I did notice small water driping on the sides of manifolds

Today I removed intake and find out that the head is cracked. I will
take apart the rest of the engine and check if anything els is bad .
Do you guys know where can I buy used parts for *5.7 V8 1990 350 cdi

Any wrecking yard. *Take the head with you so you can get a matching head.

Can you please tell me *if is going to fit from GM cars and wich
ones . What do I have to look for when I'm maching them

Today I discovered cracked block too so I have cracked blok and head.
I will need new engine what is the good place for used engines

wrote:
On Aug 30, 1:09 am, wrote:
On Aug 30, 12:42 am, "CalifBill" wrote:

wrote in message
...
On Aug 28, 10:40 am, wrote:
Ok i bought the boat with 5.7 mercruiser 1990 350 cdi . It has water
oil mix on the oil stik and it is not starting where shuld I start
looking. I did notice small water driping on the sides of manifolds
Today I removed intake and find out that the head is cracked. I will
take apart the rest of the engine and check if anything els is bad .
Do you guys know where can I buy used parts for 5.7 V8 1990 350 cdi
Any wrecking yard. Take the head with you so you can get a matching head.
Can you please tell me if is going to fit from GM cars and wich
ones . What do I have to look for when I'm maching them

Today I discovered cracked block too so I have cracked blok and head.
I will need new engine what is the good place for used engines

Your boat is 19 years old. It needs a complete repower.