removing registration numbers
 

Finally got my new Canadian license numbers for the Princecraft Yukon. (
kind off....they tell me the numbers and I have to go buy and apply them)
Is a heat gun the best way to remove Tom's Connecticut numbers?

removing registration numbers
 

Don White wrote:
Finally got my new Canadian license numbers for the Princecraft Yukon. (
kind off....they tell me the numbers and I have to go buy and apply them)
Is a heat gun the best way to remove Tom's Connecticut numbers?



He probably spit on the back of the numbers to stick them on. Proceed
cautiously.
:}

removing registration numbers
 

On Tue, 11 Sep 2007 17:38:53 -0300, "Don White"
wrote:

Finally got my new Canadian license numbers for the Princecraft Yukon. (
kind off....they tell me the numbers and I have to go buy and apply them)
Is a heat gun the best way to remove Tom's Connecticut numbers?

Hair dryer on high or a heat gun on low.

Just heat them up enough to remove them - don't get them hot - just
warm.

How's it working for you?

removing registration numbers
 

On Sep 11, 1:38?pm, "Don White" wrote:
Finally got my new Canadian license numbers for the Princecraft Yukon. (
kind off....they tell me the numbers and I have to go buy and apply them)
Is a heat gun the best way to remove Tom's Connecticut numbers?

Be prepared to do a bit of buffing in the area where the CT numbers
were applied. You're likely to see the "ghost" of the CT numbers, and
you'll essentially have to grind away enough of the aged gelcoat
surrounding the part that was protected by the CT numbers to restore
an even appearance.

removing registration numbers
 

On Tue, 11 Sep 2007 14:32:05 -0700, Chuck Gould
wrote:

On Sep 11, 1:38?pm, "Don White" wrote:
Finally got my new Canadian license numbers for the Princecraft Yukon. (
kind off....they tell me the numbers and I have to go buy and apply them)
Is a heat gun the best way to remove Tom's Connecticut numbers?

Be prepared to do a bit of buffing in the area where the CT numbers
were applied. You're likely to see the "ghost" of the CT numbers, and
you'll essentially have to grind away enough of the aged gelcoat
surrounding the part that was protected by the CT numbers to restore
an even appearance.

It's aluminum. Baked enamel paint. The boat was always stored inside
and/or covered.

The paint didn't fade.

removing registration numbers
 

Old boat I'd use a sander with heavy grit, just so you would fit in with the
basin crowd.

Short Wave Sportfishing wrote:

On Tue, 11 Sep 2007 17:38:53 -0300, "Don White"
wrote:

Finally got my new Canadian license numbers for the Princecraft Yukon. (
kind off....they tell me the numbers and I have to go buy and apply them)
Is a heat gun the best way to remove Tom's Connecticut numbers?

Hair dryer on high or a heat gun on low.

Just heat them up enough to remove them - don't get them hot - just
warm.

How's it working for you?

removing registration numbers
 

Short Wave Sportfishing wrote:
On Tue, 11 Sep 2007 14:32:05 -0700, Chuck Gould
wrote:

On Sep 11, 1:38?pm, "Don White" wrote:
Finally got my new Canadian license numbers for the Princecraft Yukon. (
kind off....they tell me the numbers and I have to go buy and apply them)
Is a heat gun the best way to remove Tom's Connecticut numbers?
Be prepared to do a bit of buffing in the area where the CT numbers
were applied. You're likely to see the "ghost" of the CT numbers, and
you'll essentially have to grind away enough of the aged gelcoat
surrounding the part that was protected by the CT numbers to restore
an even appearance.

It's aluminum. Baked enamel paint. The boat was always stored inside
and/or covered.

The paint didn't fade.

Be prepared to do a bit of buffing in the area where the CT numbers were
applied. You're likely to see the "ghost" of the CT numbers, and you'll
essentially have to buff/compound the area surrounding the part that was
protected by the CT numbers to restore/blend an even appearance.

Rob

removing registration numbers
 

Don White wrote:
Finally got my new Canadian license numbers for the Princecraft Yukon. (
kind off....they tell me the numbers and I have to go buy and apply them)
Is a heat gun the best way to remove Tom's Connecticut numbers?



Be prepared to do a bit of buffing in the area where the CT numbers were
applied. You're likely to see the "ghost" of the CT numbers, and you'll
essentially have to buff/compound the area surrounding the part that was
protected by the CT numbers to restore/blend an even appearance.

Rob

removing registration numbers
 

"Short Wave Sportfishing" wrote in message
...
On Tue, 11 Sep 2007 14:32:05 -0700, Chuck Gould
wrote:

On Sep 11, 1:38?pm, "Don White" wrote:
Finally got my new Canadian license numbers for the Princecraft Yukon. (
kind off....they tell me the numbers and I have to go buy and apply
them)
Is a heat gun the best way to remove Tom's Connecticut numbers?

Be prepared to do a bit of buffing in the area where the CT numbers
were applied. You're likely to see the "ghost" of the CT numbers, and
you'll essentially have to grind away enough of the aged gelcoat
surrounding the part that was protected by the CT numbers to restore
an even appearance.

It's aluminum. Baked enamel paint. The boat was always stored inside
and/or covered.

The paint didn't fade.

Shiny as a new toonie....
Raining here for a couple of days but I plan on taking the boat down to Cape
Breton ASAP to cruise the beautiful Bras d'Or Lakes
see...
http://img.photobucket.com/albums/v2...n/HPIM0692.jpg
and
http://img.photobucket.com/albums/v2...n/HPIM0691.jpg

removing registration numbers
 

"Dry 1" wrote in message
...
Old boat I'd use a sander with heavy grit, just so you would fit in with
the
basin crowd.



I don't want to fit in with that motley crew on the Bedford Basin..
I'm setting my sights on something higher...like Mahone Bay...or maybe St.
Margaret's Bay. ;-)
(wonder if they'd accept me at the Squadron with this boat?)