BoatBanter.com

BoatBanter.com (https://www.boatbanter.com/)
-   General (https://www.boatbanter.com/general/)
-   -   Can this be solved? (https://www.boatbanter.com/general/4920-can-solved.html)

JGK June 6th 04 04:20 AM

Can this be solved?
 
When I running my Pro-line 19 with a Merc 125 outboard pretty much wide
open and go into a hard turn, I get what seem like prop cavitations. If I
back off the throttle a little it goes away.
Not normally a problem but when I'm towing a skier it is very aggravating.
Is there an easy fix for this other than slowing down?
Thanks
John



Jeff Durham June 6th 04 04:55 AM

Can this be solved?
 
It sounds to me like your engine is mounted a little too high. I would talk
to some prop experts about this. One possibility might be to use a smaller
diameter prop, but a bigger pitch. Also, I wonder if those "whale tale"
attachments might help to resolve the problem.

Jeff


"JGK" wrote in message
.. .
When I running my Pro-line 19 with a Merc 125 outboard pretty much wide
open and go into a hard turn, I get what seem like prop cavitations. If I
back off the throttle a little it goes away.
Not normally a problem but when I'm towing a skier it is very aggravating.
Is there an easy fix for this other than slowing down?
Thanks
John





Stanley Barthfarkle June 6th 04 06:59 AM

Can this be solved?
 
I have a Sting Ray hydrofoil on my outdrive that performs wonderfully in
preventing slide-outs, and also lets me plane much more quickly and at lower
speed than without one.

BTW- with a 125 outboard, is it safe to sling a skier around at full
throttle?


"JGK" wrote in message
.. .
When I running my Pro-line 19 with a Merc 125 outboard pretty much wide
open and go into a hard turn, I get what seem like prop cavitations. If I
back off the throttle a little it goes away.
Not normally a problem but when I'm towing a skier it is very aggravating.
Is there an easy fix for this other than slowing down?
Thanks
John





Charles T. Low June 6th 04 01:35 PM

Can this be solved?
 
Could it be as simple as trimming in? Often required during hard turns.

====

Charles T. Low
- remove "UN"
www.boatdocking.com/BDPhoto.html - Photo Contest
www.boatdocking.com
www.ctlow.ca/Trojan26 - my boat

====

"JGK" wrote in message
.. .
When I running my Pro-line 19 with a Merc 125 outboard pretty much wide
open and go into a hard turn, I get what seem like prop cavitations. If I
back off the throttle a little it goes away.
Not normally a problem but when I'm towing a skier it is very aggravating.
Is there an easy fix for this other than slowing down?
Thanks
John




Tony Thomas June 6th 04 06:13 PM

Can this be solved?
 
Make sure your trim is set right.
Also, I assume you have an aluminum prop. Get a good SS prop (a 4 blade
would be great on your application). It will give you more bite in the
turns, hole shot, and probably better top end as it will provide for more
bow lift.

--
Tony
my boats at http://t.thomas.home.mchsi.com

"JGK" wrote in message
.. .
When I running my Pro-line 19 with a Merc 125 outboard pretty much wide
open and go into a hard turn, I get what seem like prop cavitations. If I
back off the throttle a little it goes away.
Not normally a problem but when I'm towing a skier it is very aggravating.
Is there an easy fix for this other than slowing down?
Thanks
John





JGK June 7th 04 12:36 AM

Can this be solved?
 

"Tony Thomas" wrote in message
news:DgIwc.14515$Sw.7812@attbi_s51...
Make sure your trim is set right.
Also, I assume you have an aluminum prop. Get a good SS prop (a 4 blade
would be great on your application).


The prop I have is a Merc SS Laser II 20" pitch but it is a 3 blade.





Tony Thomas June 7th 04 11:13 PM

Can this be solved?
 
Then prop is probably not the issue since you have a good one.
Either the engine is mounted slightly too high for hard turns or your trim
angle is wrong. You should trim down to make the turn. Thing about
lowering the engine mount is you will loose top end.
Which hole is the motor mounted w/. Remember - top hole means motor all the
way down and bottom hole means motor all the way up.

--
Tony
my boats at http://t.thomas.home.mchsi.com

"JGK" wrote in message
...

"Tony Thomas" wrote in message
news:DgIwc.14515$Sw.7812@attbi_s51...
Make sure your trim is set right.
Also, I assume you have an aluminum prop. Get a good SS prop (a 4 blade
would be great on your application).


The prop I have is a Merc SS Laser II 20" pitch but it is a 3 blade.







JGK June 8th 04 12:52 AM

Can this be solved?
 
"Tony Thomas" wrote in message
news:hM5xc.55563$3x.1392@attbi_s54...
Then prop is probably not the issue since you have a good one.
Either the engine is mounted slightly too high for hard turns or your trim
angle is wrong. You should trim down to make the turn. Thing about
lowering the engine mount is you will loose top end.
Which hole is the motor mounted w/. Remember - top hole means motor all

the
way down and bottom hole means motor all the way up.


Just went out and double checked the engine is mounted in the top holes. So
I will try trimming during the turns.
Thanks




JGK June 8th 04 12:53 AM

Can this be solved?
 
"Stanley Barthfarkle" wrote in message
y.com...
BTW- with a 125 outboard, is it safe to sling a skier around at full
throttle?

Don't know if it safe, but as a skier it sure is fun!







All times are GMT +1. The time now is 10:19 AM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 BoatBanter.com