re-flooring boat
 

Hello,

Please could anyone advise me: I've got a 15ft fibre glass boat with wooden
floor the floor has some fibre glass resin at the sides presumably to fix it
in place.

My problem is the floor is rotten! I also need to get under it to see if
theres any damage
to the bottom of the boat underneath.

Can you please advise me if I should lift this old ply floor or perhaps seal
it and put another layer of ply and also if there should be many holes in
it?!?!?!?

Thanks
Jim

re-flooring boat
 

On Fri, 16 Jan 2004 21:31:36 -0000, "Jim"
wrote:

Hello,

Please could anyone advise me: I've got a 15ft fibre glass boat with wooden
floor the floor has some fibre glass resin at the sides presumably to fix it
in place.

My problem is the floor is rotten! I also need to get under it to see if
theres any damage to the bottom of the boat underneath.

Can you please advise me if I should lift this old ply floor or perhaps seal
it and put another layer of ply and also if there should be many holes in
it?!?!?!?

When you say "hole in the floor" is there a space between the floor
and the outer hull? In other words, is the floor placed on a stringer
system of some sort or is it layed on some sort of core?

I'm going to assume that the "floor" of the boat is actually part of
the hull because of it's size. If it is a balsa or foam cored boat,
then you might have a problem - the balsa/foam is part of the
construction and can't be replaced as such - you might as well build a
new boat. The only reason I say this is because I've had a couple of
14/15 foot Crestliners here along with a couple of MFGs, etc. that I
removed some antique outboards from. All the boats were built with
this balsa and/or foam core construction when I cut them up for
disposal and every single one of them had a rotten floor.

Finally, If your floor is soft, it's a pretty good bet that the
transom is probably soft also. I'd check that.

Later,

Tom
S. Woodstock, CT
----------
"My rod and my reel - they comfort me."

St. Pete, 12 Lb. Test

re-flooring boat
 

"Short Wave Sportfishing" wrote in message
...
On Fri, 16 Jan 2004 21:31:36 -0000, "Jim"
wrote:

Hello,

Please could anyone advise me: I've got a 15ft fibre glass boat with
wooden
floor the floor has some fibre glass resin at the sides presumably to fix
it
in place.

My problem is the floor is rotten! I also need to get under it to see if
theres any damage to the bottom of the boat underneath.

Can you please advise me if I should lift this old ply floor or perhaps
seal
it and put another layer of ply and also if there should be many holes in
it?!?!?!?

When you say "hole in the floor" is there a space between the floor
and the outer hull? In other words, is the floor placed on a stringer
system of some sort or is it layed on some sort of core?

I'm going to assume that the "floor" of the boat is actually part of
the hull because of it's size. If it is a balsa or foam cored boat,
then you might have a problem - the balsa/foam is part of the
construction and can't be replaced as such - you might as well build a
new boat. The only reason I say this is because I've had a couple of
14/15 foot Crestliners here along with a couple of MFGs, etc. that I
removed some antique outboards from. All the boats were built with
this balsa and/or foam core construction when I cut them up for
disposal and every single one of them had a rotten floor.

Finally, If your floor is soft, it's a pretty good bet that the
transom is probably soft also. I'd check that.

Later,

Tom
S. Woodstock, CT
----------
"My rod and my reel - they comfort me."

St. Pete, 12 Lb. Test

If it is just the floor. You can cut it out and build a new floor with
plywood and resin / glass. But if you go this way, measure the width of the
boat at several places along the length of the floor. Maybe even build a
2x4 bracing system to keep the boat from flexing outward when the floor is
removed. We did a buddy's Reinell a few years ago, transom was or, just the
floor bad. We learned we should of measured the width before removing
floor.

re-flooring boat
 

Around 1/16/2004 1:31 PM, Jim wrote:

My problem is the floor is rotten! I also need to get under it to see if
theres any damage
to the bottom of the boat underneath.


Time to replace the floor. It's not very difficult, but this book
(highly recommended by members of the Classic Glastron Owners
Association) should help walk you through the process:
http://www.amazon.co.uk/exec/obidos/ASIN/0071580085

--
~/Garth - 1966 Glastron V-142 Skiflite: "Blue-Boat"
"There is nothing - absolutely nothing - half so much worth doing
as simply messing about in boats."
-Kenneth Grahame, The Wind in the Willows

re-flooring boat
 

Subject: re-flooring boat
From: "Jim"

Can you please advise me if I should lift this old ply floor or perhaps seal

Remove and replace.

it and put another layer of ply and also if there should be many holes in
it?!?!?!?

There should as few holes as possible. And what holes there need to be should
be well sealed.

Capt. Bill

re-flooring boat
 

Sorry , missed a sentence the Liquid nail and the 1/8" spreading trial
was used for the Carpet that was put down.
Thanks,
Brian

Brian Owens wrote:

Jim,
I am in the process for re-flooring my 17' bass boat. Even though it
is not difficult, you do need alot of patients. Basicly all you have
to do is take the old plywood off, and use it as a template. For me I
went to Home Depot and got an exterior OSB board and sealed it with a
epoxy paint, and used a gallon of Liquid nail and a 1/8" spreading
trial . Make sure you seal the edges really good and that should last
you for a while. Good luck and remember.

PATIENTS!
PATIENTS!
PATIENTS!
PATIENTS!

Brian

Jim wrote:

Hello,

Please could anyone advise me: I've got a 15ft fibre glass boat with
wooden
floor the floor has some fibre glass resin at the sides presumably to
fix it
in place.

My problem is the floor is rotten! I also need to get under it to see if
theres any damage
to the bottom of the boat underneath.

Can you please advise me if I should lift this old ply floor or
perhaps seal
it and put another layer of ply and also if there should be many
holes in
it?!?!?!?

Thanks
Jim

re-flooring boat
 

"martin" wrote in message
...
On Fri, 30 Jan 2004 10:07:22 -0500, Brian Owens
wrote:
Bla Bla Bla
Make sure you seal the edges really good and that should last you for a
while. Good luck and remember.

PATIENTS!
PATIENTS!
PATIENTS!
PATIENTS!

Are you a doctor?
--
Martin
No he's probably a Yank & can't write proper English. But at least he's
wtiting something useful, not like the rest of us. Peter

re-flooring boat
 

"Brian Owens" wrote in message
...
Sorry , missed a sentence the Liquid nail and the 1/8" spreading trial
was used for the Carpet that was put down.
Thanks,
Brian


Is this liquid nail stuff readily available? Does it flow better than no
nails?

re-flooring boat
 

"roddytoo" wrote in message
...

"Brian Owens" wrote in message
...
Sorry , missed a sentence the Liquid nail and the 1/8" spreading trial
was used for the Carpet that was put down.
Thanks,
Brian


Is this liquid nail stuff readily available? Does it flow better than no
nails?



Very available. You probably want the subfloor glue version. Lowes, HD,
any lumber yard carries it.

re-flooring boat
 

He's in the UK so the product names might be different.

They make a special indoor/outdoor carpet adhesive. The potential problem with
some liquid nail-type products is that they can "melt" certain types of plastics
or bleed through.

Dan


Calif Bill wrote:

"roddytoo" wrote in message
...

"Brian Owens" wrote in message
...

Sorry , missed a sentence the Liquid nail and the 1/8" spreading trial
was used for the Carpet that was put down.
Thanks,
Brian


Is this liquid nail stuff readily available? Does it flow better than no
nails?




Very available. You probably want the subfloor glue version. Lowes, HD,
any lumber yard carries it.