Home |
Search |
Today's Posts |
|
#1
|
|||
|
|||
Royalex
On Wed, 12 May 2004 16:03:19 -0000, Bill Tuthill
wrote: riverman wrote: Sounds like Royalex is a tradename for polypropylene. Is it? ABS = acrylonitrilebutylstyrene Definitely not polypropylene. Royalex is a tradename owned by Uniroyal. ABS, Royalex, and several others are similar, but not identical, sandwiches of ABS plus foam plus a vinyl, colored outer skin. Tom McCloud |
#2
|
|||
|
|||
Royalex
Te,
Re-molding the basic hull shape of a Royalite canoe seems to me an iffy proposition at best. I don't know anyone who has this as dramaticaly as you propose, but I can think of quite a few things that could go wrong. A friend with a Mohawk Nova 16 on R-84 was unsatisfied with the oilcanning of that hull (which was very noticable). His solution was to steam bend some halfround hardwood molding and make a couple of ribs which run from gunwale to gunwale, glassing them in place with epoxy resin and fiberglass tape. It helped quite a bit with the oil canning, didn't add much weight and doesn't look too bad. My concern with his approach was the longevity of the fix, thinking that the rib/glass would seperate from the hull on an impact or when sliding the loaded boat over a barely submerged log. So far, so good - although the canoe sees mostly easy water and gentle use. Mike "Te Canaille" wrote in message Hey Riverman, sure seems like you've had some experience with this. I have a related question. My Royalite Canoe which is a 13' footer has begun oil canning. It's got a flat bottom, hard chines, and a bit of tumblehome. I figured the oil canning could be stopped if I can make a shallow arch or V-bottom configuration in cross-section. So here's what I thought to do, first mount a section of plywood lengthwise on a strongback, then invert and center the canoe over the plywood so that it is resting on the interior deck along the length of the hull. Then put several straps over the canoe and stake to the ground with enough force to cause a curvature in cross-section. Then apply some heat ( don't think a hair dyer would do ) to make the hull assume the desire curvature. I'm a bit woried about how symmetrical the result will be but if I monitor the shape and adjust straps as I go it should not get too warped. I'd like to hear some thoughts about this. Actually, I figure to curve the plywood just a bit for a slight amount of rocker. Te Canaille |
#3
|
|||
|
|||
Royalex
"Mike McCrea" wrote in message om... Te, Re-molding the basic hull shape of a Royalite canoe seems to me an iffy proposition at best. I don't know anyone who has this as much deleted Thanks Mike. I appreciate the feedback. I think I might try the reinforcement approach that you discuss. Say, didn't I see an article by you in the current "Paddler" about lake paddling ? Nicely done. Te Canaille |
#4
|
|||
|
|||
Royalex
Alan,
I've rebuilt a couple dozen Royalex canoes, most of which were dumpster-ready when I got them. Pretty much if you still have all of the pieces of the hull it can be put right. Send me an e-mail and describe the damage, and I can walk you through what you'll need to do to repair it. Mike McCrea (Alan) wrote in message . com... Hi, We had a splendid weekend in the Ardennes until I made a mistake. How can I repair a royalex canoe after a serious crash? Cheers, Alan. |
Reply |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Watermark Royalex Canoe | General | |||
Bell Prodigy and the Rival and Royalex | General | |||
Comments on Bell Prodigy WW Canoe? | General |