Home |
Search |
Today's Posts |
|
#1
|
|||
|
|||
Vertical clearance ??
|
#2
|
|||
|
|||
Vertical clearance ??
Vertical clearance is usually measured above high water. The only
significant exception is small scale charts where the datum may be Mean Sea Level. Such charts rarely show bridge clearances, so the difference isn't an issue. The exact datum varies from country to country. On US domestic charts, it's always Mean High Water (the average of all high tides). On foreign charts, including US charts made from foreign data, it's usually a higher datum, Mean Higher High Water (the average of the higher of the two high tides each day), Mean High Water Springs (the average of all spring tides), Highest Astronomical Tide (the highest the water ever gets without help from a storm) or maybe something else. May I suggest that you buy a copy of Bowditch (The American Practical Navigator -- NIMA Pub 9) which will answer this question and every other question you ever had about navigation? Bowditch just had its 200th anniversary of being continuously in print, through about 75 editions. It's the standard source of basic information on all kinds of navigation. There's no need to buy it new -- any edition from the last forty years will do fine. I might add, that as a serious navigator, I own two copies of Bowditch (1962 and 1977) and don't own Chapman. Jim Woodward www.mvfintry.com "Steve" wrote in message ... Were is vertical clearance measured from (what datum)? I can't seem to find this information in any of my reference books. What I find in Chapman's, in a section on chart "Plane of Reference", states "Different planes are on different charts of various boating areas. For charts along the Atlantic coast the National Ocean Survey uses mean low water as the datum for soundings. On the Pacific coast it is the mean lower low water that is used for the reference plane....." No mention of vertical clearance. Here in the Pacific NW where tide difference are signicant the chart datum is not metioned in my Maptech Reg. 15 portfolio (or I just can't find it). Example: Today the vertical clearance under two different bridges was just too close to take a chance on and it was a +8 ft tide. I ended up playing it safe and had the draw span opened on the Hood Canal floating bridge and went out of my way to avoid going through the the Port Townsend Canal with an overhead bridge span. In each case the "stated" Vertical Clearance was enough for my 54 ft 7 inch requirement, but I had no idea what tidal state their datum was based on. (Hood Canal Bridge, east span was 55ft vert. clearance while P.T. Canal bridge was 58ft.) Sure hope the 10-20 min traffic delay for some 200 cars and trucks wasn't due to my cautions and lack of knowledge on this matter.. Please enlighten me. Steve s/v Good Intentions |
#3
|
|||
|
|||
Vertical clearance ??
The link that I posted before was to the tide chapter in Bowditch. The entire contents
are online at: http://pollux.nss.nima.mil/pubs/pubs...s.html?rid=187 There are two versions of the latest Bowditch available in hard copy - the one from the government includes a CD which has a wrapper program to do some of the navigation for you. It also has a calculator and a few other features. I don't know if the "commercial" version - roughly the same price, also has that. Old editions of Bowditch are fun - I have several, including a first and one from 1870 - I like to see what the practices and terminology was back then. "Jim Woodward" wrote in message om... Vertical clearance is usually measured above high water. The only significant exception is small scale charts where the datum may be Mean Sea Level. Such charts rarely show bridge clearances, so the difference isn't an issue. The exact datum varies from country to country. On US domestic charts, it's always Mean High Water (the average of all high tides). On foreign charts, including US charts made from foreign data, it's usually a higher datum, Mean Higher High Water (the average of the higher of the two high tides each day), Mean High Water Springs (the average of all spring tides), Highest Astronomical Tide (the highest the water ever gets without help from a storm) or maybe something else. May I suggest that you buy a copy of Bowditch (The American Practical Navigator -- NIMA Pub 9) which will answer this question and every other question you ever had about navigation? Bowditch just had its 200th anniversary of being continuously in print, through about 75 editions. It's the standard source of basic information on all kinds of navigation. There's no need to buy it new -- any edition from the last forty years will do fine. I might add, that as a serious navigator, I own two copies of Bowditch (1962 and 1977) and don't own Chapman. Jim Woodward www.mvfintry.com "Steve" wrote in message ... Were is vertical clearance measured from (what datum)? I can't seem to find this information in any of my reference books. What I find in Chapman's, in a section on chart "Plane of Reference", states "Different planes are on different charts of various boating areas. For charts along the Atlantic coast the National Ocean Survey uses mean low water as the datum for soundings. On the Pacific coast it is the mean lower low water that is used for the reference plane....." No mention of vertical clearance. Here in the Pacific NW where tide difference are signicant the chart datum is not metioned in my Maptech Reg. 15 portfolio (or I just can't find it). Example: Today the vertical clearance under two different bridges was just too close to take a chance on and it was a +8 ft tide. I ended up playing it safe and had the draw span opened on the Hood Canal floating bridge and went out of my way to avoid going through the the Port Townsend Canal with an overhead bridge span. In each case the "stated" Vertical Clearance was enough for my 54 ft 7 inch requirement, but I had no idea what tidal state their datum was based on. (Hood Canal Bridge, east span was 55ft vert. clearance while P.T. Canal bridge was 58ft.) Sure hope the 10-20 min traffic delay for some 200 cars and trucks wasn't due to my cautions and lack of knowledge on this matter.. Please enlighten me. Steve s/v Good Intentions |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
zero clearance cutting tools? | Boat Building |