BoatBanter.com

BoatBanter.com (https://www.boatbanter.com/)
-   Boat Building (https://www.boatbanter.com/boat-building/)
-   -   transom replacement on an inflatable (https://www.boatbanter.com/boat-building/76751-transom-replacement-inflatable.html)

Jack Rogers December 18th 06 02:55 PM

transom replacement on an inflatable
 
Hello--

I've got a west marine inflatable dinghy (model sb285, built by zodiac,
about 9 ft long) with a rotten transom. The plywood transom is attached
to rubber moldings on either side and these are bonded to the tubes. Has
anyone ever replaced the transom on a boat like this? It looks like
best way would be to unglue the rubber boots from the hull tubes and
replace the whole thing as a unit. Any advice appreciated!!

Thanks--Jack Rogers

James December 18th 06 04:18 PM

transom replacement on an inflatable
 
Jack Rogers wrote:

Hello--

I've got a west marine inflatable dinghy (model sb285, built by
zodiac, about 9 ft long) with a rotten transom. The plywood transom
is attached to rubber moldings on either side and these are bonded to
the tubes. Has anyone ever replaced the transom on a boat like this?
It looks like best way would be to unglue the rubber boots from the
hull tubes and replace the whole thing as a unit. Any advice
appreciated!!

Thanks--Jack Rogers


Would it be possible to stabilize the rot with something like GitRot or
System 3's Fix-Rot and then rebuild with epoxy or use an overlay of HDO
or Richlite. I've gotten small pieces of HDO from outdoor sign
manufactures and Richlite is used in counter tops. www.richlite.com has
a list of dealers/users. I'm presently using Richlite to rebuild the
front hatch opening on our 28' Irwin. Removed the sliding hatch and
replacing with a Bomar. Jim

--


Jack Rogers December 18th 06 07:09 PM

transom replacement on an inflatable
 
In article ,
"James" wrote:

Jack Rogers wrote:

Hello--

I've got a west marine inflatable dinghy (model sb285, built by
zodiac, about 9 ft long) with a rotten transom. The plywood transom
is attached to rubber moldings on either side and these are bonded to
the tubes. Has anyone ever replaced the transom on a boat like this?
It looks like best way would be to unglue the rubber boots from the
hull tubes and replace the whole thing as a unit. Any advice
appreciated!!

Thanks--Jack Rogers


Would it be possible to stabilize the rot with something like GitRot or
System 3's Fix-Rot and then rebuild with epoxy or use an overlay of HDO
or Richlite. I've gotten small pieces of HDO from outdoor sign
manufactures and Richlite is used in counter tops. www.richlite.com has
a list of dealers/users. I'm presently using Richlite to rebuild the
front hatch opening on our 28' Irwin. Removed the sliding hatch and
replacing with a Bomar. Jim


No such luck--the wood is really mush extending all the way back into
the slot where it connects to the rubber boot.

thx--jack

den December 20th 06 03:22 AM

transom replacement on an inflatable
 

Jack Rogers wrote:
In article ,


No such luck--the wood is really mush extending all the way back into
the slot where it connects to the rubber boot.
thx--jack

Den wrote....
It looks like you are in the market for a sheet of marine ply. Maybe
use several sheets laminated together with repoxy. I used black 3M 5200
to stick a transom together. (to the tubes). The transom had separated
from the tubes, and the bottom. Really difficult to clamp, and jig for
the 4 day cure time. I did it in several steps. Unfortunately a renter
ran over the starboard aft chamber and popped it, so I gave up, and
never got it in the water. When I rolled it up, it seemed to still be
holding.


den December 20th 06 03:27 AM

transom replacement on an inflatable
 

den wrote:

never got it in the water. When I rolled it up, it seemed to still be
holding.


Forgot to mention! USE THE BOOTS. They give you lots of gluing area.
Otherwise gotta use special glue which I have never heard of working
well.



All times are GMT +1. The time now is 11:49 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 BoatBanter.com