Looking for 1/8" solid T&H veneer
 

Looking for 1/8" solid Teak and Holly veneer.
Near Connecticut would be nice.

Looking for 1/8" solid T&H veneer
 

If you find some anywhere in the world, let me know. I have looked for
6 years. Thare ain't no such animal. You can get teak and "holly"
veneered plywood but the face veneer is only about 1/32nd. I ended up
resawing and planing some solid 8/4 teak and real 4/4 holly to 3/16 and
laying it.

ddinc wrote:

Looking for 1/8" solid Teak and Holly veneer.
Near Connecticut would be nice.




--
Glenn Ashmore

I'm building a 45' cutter in strip/composite. Watch my progress (or lack
there of) at: http://www.rutuonline.com
Shameless Commercial Division: http://www.spade-anchor-us.com

Looking for 1/8" solid T&H veneer
 

I don't think it is considered veneer when it is 1/8th-inch solid but
I can assure you no one manufacturers it. You might find someone to
make it up for you but I'd hate to think what you would pay. If you
need it that badly and nothing else will do you will have to do what I
did (only for a section around my mast step): Mill it yourself if you
have a planer. If not buy whatever you can get, probably 4/4 and have
someone else mill it. You can then edge glue, remembering all the
preparation you need to glue teak (scrubbing with acetone, allowing to
dry) and you might even want to use biscuits as I did though I was
using 3/8ths. You will also need to select yhour glue carefully. I
used West System epoxy though urethane, resourcinol, or even the new
Titebond III might work. Moreover, you will not find decent holly
easy to come by. Most all of the T&H plywood today is made with maple
or other light-colored hardwoods.

On Mon, 19 Apr 2004 22:20:13 -0400, Glenn Ashmore
wrote:

If you find some anywhere in the world, let me know. I have looked for
6 years. Thare ain't no such animal. You can get teak and "holly"
veneered plywood but the face veneer is only about 1/32nd. I ended up
resawing and planing some solid 8/4 teak and real 4/4 holly to 3/16 and
laying it.

ddinc wrote:

Looking for 1/8" solid Teak and Holly veneer.
Near Connecticut would be nice.

Looking for 1/8" solid T&H veneer
 

Try World Panel Products here in FL, they will ship.
http://www.worldpanel.com/Marineplywoodsspecialty.htm
About 1/3 down the page, they have 1/2" plywood with 3 mm ( about 1/8" )
thick teak strips without holly but you could insert that your self. Another
alternative ( if you like how it looks) would be solid teak tongue and
groove flooring, pretty easy to install and can be sanded many times in case
of dents or other problems.

Good luck
J.T.

"ddinc" wrote in message
...
Looking for 1/8" solid Teak and Holly veneer.
Near Connecticut would be nice.

Looking for 1/8" solid T&H veneer
 

Actually I found this. 1/4" and 1/16"

4' x 8' x 1/4" Teak & Holly $125.00 per sheet FOB Boston

We do stock a 1/16" Teak & Holly veneer with no backer $125.00 per sheet FOB
Boston, I would suggest laminating this to a 1/16" okoume core.


Christopher F. Boulter
Boulter Plywood Corp.
24 Broadway
Somerville, MA 02145
617-666-1340

www.boulterplywood.com



"Glenn Ashmore" wrote in message
news:rN%gc.5273$uF3.3377@lakeread04...
If you find some anywhere in the world, let me know. I have looked for
6 years. Thare ain't no such animal. You can get teak and "holly"
veneered plywood but the face veneer is only about 1/32nd. I ended up
resawing and planing some solid 8/4 teak and real 4/4 holly to 3/16 and
laying it.

ddinc wrote:

Looking for 1/8" solid Teak and Holly veneer.
Near Connecticut would be nice.




--
Glenn Ashmore

I'm building a 45' cutter in strip/composite. Watch my progress (or lack
there of) at: http://www.rutuonline.com
Shameless Commercial Division: http://www.spade-anchor-us.com

Looking for 1/8" solid T&H veneer
 

I am vacuuming onto carbon/honeycomb panel for floorboards.
I am looking to save the weight of the plywood.

"J.T. Tuomela" wrote in message
...
Try World Panel Products here in FL, they will ship.
http://www.worldpanel.com/Marineplywoodsspecialty.htm
About 1/3 down the page, they have 1/2" plywood with 3 mm ( about 1/8" )
thick teak strips without holly but you could insert that your self.
Another
alternative ( if you like how it looks) would be solid teak tongue and
groove flooring, pretty easy to install and can be sanded many times in
case
of dents or other problems.

Good luck
J.T.

"ddinc" wrote in message
...
Looking for 1/8" solid Teak and Holly veneer.
Near Connecticut would be nice.

Looking for 1/8" solid T&H veneer
 

Check and make sure that is not a 1/32 teak/holly face on a crossgrain
veneer layer.

ddinc wrote:
Actually I found this. 1/4" and 1/16"

4' x 8' x 1/4" Teak & Holly $125.00 per sheet FOB Boston

We do stock a 1/16" Teak & Holly veneer with no backer $125.00 per sheet FOB
Boston, I would suggest laminating this to a 1/16" okoume core.


Christopher F. Boulter
Boulter Plywood Corp.
24 Broadway
Somerville, MA 02145
617-666-1340

www.boulterplywood.com



"Glenn Ashmore" wrote in message
news:rN%gc.5273$uF3.3377@lakeread04...

If you find some anywhere in the world, let me know. I have looked for
6 years. Thare ain't no such animal. You can get teak and "holly"
veneered plywood but the face veneer is only about 1/32nd. I ended up
resawing and planing some solid 8/4 teak and real 4/4 holly to 3/16 and
laying it.

ddinc wrote:


Looking for 1/8" solid Teak and Holly veneer.
Near Connecticut would be nice.




--
Glenn Ashmore

I'm building a 45' cutter in strip/composite. Watch my progress (or lack
there of) at: http://www.rutuonline.com
Shameless Commercial Division: http://www.spade-anchor-us.com





--
Glenn Ashmore

I'm building a 45' cutter in strip/composite. Watch my progress (or lack
there of) at: http://www.rutuonline.com
Shameless Commercial Division: http://www.spade-anchor-us.com

Looking for 1/8" solid T&H veneer
 

I've seen some t&h 1/4" ply where the face veneer was less than 1/32".
I suggest that you get a sample and see how few strokes it takes to sand through
it.


Glenn Ashmore wrote:

Check and make sure that is not a 1/32 teak/holly face on a crossgrain
veneer layer.

ddinc wrote:
Actually I found this. 1/4" and 1/16"

4' x 8' x 1/4" Teak & Holly $125.00 per sheet FOB Boston

We do stock a 1/16" Teak & Holly veneer with no backer $125.00 per sheet FOB
Boston, I would suggest laminating this to a 1/16" okoume core.


Christopher F. Boulter
Boulter Plywood Corp.
24 Broadway
Somerville, MA 02145
617-666-1340

www.boulterplywood.com



"Glenn Ashmore" wrote in message
news:rN%gc.5273$uF3.3377@lakeread04...

If you find some anywhere in the world, let me know. I have looked for
6 years. Thare ain't no such animal. You can get teak and "holly"
veneered plywood but the face veneer is only about 1/32nd. I ended up
resawing and planing some solid 8/4 teak and real 4/4 holly to 3/16 and
laying it.

ddinc wrote:


Looking for 1/8" solid Teak and Holly veneer.
Near Connecticut would be nice.




--
Glenn Ashmore

I'm building a 45' cutter in strip/composite. Watch my progress (or lack
there of) at: http://www.rutuonline.com
Shameless Commercial Division: http://www.spade-anchor-us.com





--
Glenn Ashmore

I'm building a 45' cutter in strip/composite. Watch my progress (or lack
there of) at: http://www.rutuonline.com
Shameless Commercial Division: http://www.spade-anchor-us.com

Looking for 1/8" solid T&H veneer
 

"ddinc" wrote in message ...
Actually I found this. 1/4" and 1/16"

4' x 8' x 1/4" Teak & Holly $125.00 per sheet FOB Boston

We do stock a 1/16" Teak & Holly veneer with no backer $125.00 per sheet FOB
Boston, I would suggest laminating this to a 1/16" okoume core.


I have a Foley if you need to plane anything down and there is a guy
locally that has a "Timesaver" 48" wide drum/belt sander for panels.
We are both in the Essex Ct area, Scotty


Christopher F. Boulter
Boulter Plywood Corp.
24 Broadway
Somerville, MA 02145
617-666-1340

www.boulterplywood.com



"Glenn Ashmore" wrote in message
news:rN%gc.5273$uF3.3377@lakeread04...
If you find some anywhere in the world, let me know. I have looked for
6 years. Thare ain't no such animal. You can get teak and "holly"
veneered plywood but the face veneer is only about 1/32nd. I ended up
resawing and planing some solid 8/4 teak and real 4/4 holly to 3/16 and
laying it.

ddinc wrote:

Looking for 1/8" solid Teak and Holly veneer.
Near Connecticut would be nice.




--
Glenn Ashmore

I'm building a 45' cutter in strip/composite. Watch my progress (or lack
there of) at: http://www.rutuonline.com
Shameless Commercial Division: http://www.spade-anchor-us.com