If you know a good site for info about this part of boat ??

Or, can you explain it here.

So far I know ,,,, hole in boat for shaft to go through from engine. Is
the cutlass bearing what lets the shaft turn and not let the water in?

What and where is the stuffing box?

Thomas,
the "tube" that your shaft exits the hull is your shaft log. The
cutlass bearing(s) are usually rubber lined tubes of fiberglass or
bronze inserted into the shaft log to keep the shaft centered and
prevent damage to the log and wear on the shaft,they are grooved to
allow water to lubricate the bearing surface and are thus not a water
barrier. They are typically held in place by set screws. the stuffing
box is coupled to the shaft log at the inside end by a hose and
clamps...It is usually a bronze pipe-like device with a chambered end
and cap through which the shaft passes.around the shaft in the upper
end of the stuffing box are several "rings" of a flax or teflon
impregnated packing material. The cap is tightened down against the
"pipe" to compress the packing material between the wall of the
stuffing box and the shaft forming the water boundary(should still
allow a small amount of water to pass when running to prevent burning
up the packing) On wooden boats they often use a flanged stuffing box
on both ends of a drilled timber shaft log in lieu of cutlass bearings.
The stuffing boxes work much the same way as the packing on the shaft
of a standard gate-valve(water valve such as for your washing machine
or garden hose bib)
hope this helps...
regards,
markvictor
Visit my new group Bad Boat Biz here on Google
(shameless plug)

Tom,
I have been watching your other posts as well as this one and it is pretty
clear you are in the beginning stages of consideration for boat ownership.
I'm going to lay out some facts of life you probably won't want to read, but
do need to know.

1) Building a boat is not cheaper than buying one.
2) Owning a boat, using a boat, insuring a boat, establishing a place for a
boat is expensive.
3) Boat maintenance will take most of your free time.
4) If you are married, a boat will be the least popular thing you could
undertake with your other half.
5) The boat hull is 20% of the investment.
6) The majority of boat building attempts fail. The larger the boat, the
greater the failure rate.
7) Number one reason for failure in building is underestimating the total
cost in both money and time.

There are more, but your posts indicate to me that you do not have the
available money, the skills or the tools to either build or own a boat in
the class you are considering. Building a boat is very rewarding and I do
not wish to discourage you, but reality is alive and well. My advise to you
is to build a small day boat first. Get your feet wet. Failure is affordable
and success is just as sweet.
Steve


"Thomas Wentworth" wrote in message
news:huBtf.1992$zJ3.65@trnddc04...
If you know a good site for info about this part of boat ??

Or, can you explain it here.

So far I know ,,,, hole in boat for shaft to go through from engine. Is
the cutlass bearing what lets the shaft turn and not let the water in?

What and where is the stuffing box?

I agree with the previous post

BUT

There are a lot of cheep used boats that can be restored for a few cents on
the dollar. If you have basic mechanical and carpentry skills some money,
time and an interested helper/partner this could be a very rewarding way to
go. The best part is that you can choose a boat design in person not just
some study plans, see it touch it and maybe even take it for a run before
committing to it. Check places like E-Bay, there are lots of
used/damaged/repairable boats for sale. Your local newspaper would also be a
good source. If you buy a boat like this and you loose interest it will
probably still have some resale value where a pile of expensive lumber and
resin would be more difficult to get rid of.

Good luck
John
Successful restorer of 3 sailboats
1) 17' General Picnic
2) Catalina C-22 (A really great first boat)
3) 31' C&C Corvette (Current project)

"Steve Lusardi" wrote in message
...
Tom,
I have been watching your other posts as well as this one and it is pretty
clear you are in the beginning stages of consideration for boat ownership.
I'm going to lay out some facts of life you probably won't want to read,
but do need to know.

1) Building a boat is not cheaper than buying one.
2) Owning a boat, using a boat, insuring a boat, establishing a place for
a boat is expensive.
3) Boat maintenance will take most of your free time.
4) If you are married, a boat will be the least popular thing you could
undertake with your other half.
5) The boat hull is 20% of the investment.
6) The majority of boat building attempts fail. The larger the boat, the
greater the failure rate.
7) Number one reason for failure in building is underestimating the total
cost in both money and time.

There are more, but your posts indicate to me that you do not have the
available money, the skills or the tools to either build or own a boat in
the class you are considering. Building a boat is very rewarding and I do
not wish to discourage you, but reality is alive and well. My advise to
you is to build a small day boat first. Get your feet wet. Failure is
affordable and success is just as sweet.
Steve


"Thomas Wentworth" wrote in message
news:huBtf.1992$zJ3.65@trnddc04...
If you know a good site for info about this part of boat ??

Or, can you explain it here.

So far I know ,,,, hole in boat for shaft to go through from engine. Is
the cutlass bearing what lets the shaft turn and not let the water in?

What and where is the stuffing box?

"Steve Lusardi" wrote in message
...
Tom,
I have been watching your other posts as well as this one and it is pretty
clear you are in the beginning stages of consideration for boat ownership.
I'm going to lay out some facts of life you probably won't want to read,
but do need to know.

1) Building a boat is not cheaper than buying one.
2) Owning a boat, using a boat, insuring a boat, establishing a place for
a boat is expensive.
3) Boat maintenance will take most of your free time.
4) If you are married, a boat will be the least popular thing you could
undertake with your other half.
5) The boat hull is 20% of the investment.
6) The majority of boat building attempts fail. The larger the boat, the
greater the failure rate.
7) Number one reason for failure in building is underestimating the total
cost in both money and time.

There are more, but your posts indicate to me that you do not have the
available money, the skills or the tools to either build or own a boat in
the class you are considering. Building a boat is very rewarding and I do
not wish to discourage you, but reality is alive and well. My advise to
you is to build a small day boat first. Get your feet wet. Failure is
affordable and success is just as sweet.
Steve


"Thomas Wentworth" wrote in message
news:huBtf.1992$zJ3.65@trnddc04...
If you know a good site for info about this part of boat ??

Or, can you explain it here.

So far I know ,,,, hole in boat for shaft to go through from engine. Is
the cutlass bearing what lets the shaft turn and not let the water in?

What and where is the stuffing box?



------------------------------------------

Dear Steve ,,,,,,,,,, oh contraire, my friend. I have actually owned and
sailed three [3] full keel, sailboats.

In fact, one of them was quite famous. But ............... and here is the
BUT part ;;; it was 20 plus years ago.

I think I have forgotten more than I ever knew. As I look into returning to
the high seas, I find that certain aspects of boat owning, maintenace,
repair, operation, cost, etc have either changed dramatically or I can't
remember the method, or procedure to follow. In some cases, such as the
Cutlass Bearing ... I just never had to deal with it as the marina did the
maintenance. That is one difference now; I plan on doing most of my own
work. I have the time ...

I also have two sons who are interested in sailing. At least today they
are.

As for the money ... to be honest, I could go out and purchase a sailboat.
I don't wish to. Why? I want to do it my way. I want things set up for
me. I want a boat that reflects my personal approach to life. I have been
on the fancy piece of fiberglass with all the blocks and sails and the gear
that never gets used. I've sat on boats that never leave the harbor. I've
talked to owners who think of sailing as writing a check. Ever hear of the
New York Yacht Club.

They are to be avoided at all cost. When Wall st goes sailing
................. you don't want to be there.

So,,,, before you make assumptions ..................

Now ............ back to the Cutlass Bearing ...

Let's see ,,, the shaft goes through a shaft log,,, and it is held in place
by a Cutlass Bearing and then there is the stuffing box ....

I'm almost ready for my first "MARINA BILL"..


TALLY HO.

I've also been confused by the term, but I have seen it applied to the
strut/bearing carrying the shaft outboard of the hull.

Roger

http://home.insightbb.com/~derbyrm

"Thomas Wentworth" wrote in message
news:iJStf.2010$WX3.1725@trndny09...

snip

Now ............ back to the Cutlass Bearing ...

Let's see ,,, the shaft goes through a shaft log,,, and it is held in
place by a Cutlass Bearing and then there is the stuffing box ....

The Cutless bearing is actually a bushing in the strut that holds the
prop shaft on some boats. Not all sailboats have one. When the boat
is out of the water, grab the prop and shake it from side to side. If
it goes THUNK THUNK, it needs replacing. If it just goes rattle
rattle, its still ok. To get an education, go around the boat yard
shaking the props on various boats and you will get a good idea of what
is good and bad. There are an amazing number of boats out there with
worn out cutless bearing and maybe it is not a problem for them.

Very few of the damaged boats I have seen on Ebay are worthwhile. When
they say "slight easily repairable damage", it seems to mean the glass
has been crushed in such a way that the layers have delaminated over
the entire side.

Thomas,
There was no insult intended, only good advice. Building or restoring a boat
will involve a lot of learning and gathering of skills you probably do not
have yet, but to do that is a lot of fun, if you can afford the time
investment and I wish you all the success possible. On your original
question, a cutlass bearing is a metal tube with a fluted rubber insert
through which a propeller shaft extends. Typically this bearing is supported
by a strut which is fastened to the bottom of the hull. Cutlass bearings are
"Limited Duty" bearings found mostly in inboard engined pleasure boats. They
must be lubricated by water flow, hence their mounting in struts in clear
open water. They may also be mounted in the deadwood of full keel boats, but
if mounted there, some provision must be made to provide adequate water
flow. This can be done by scoops or by engine driven pump as by the outlet
of an engine heat exchanger. Commercial craft typically use oil or grease
lubed plain bearings. Cutlass bearings will wear the propeller shaft, so
they are rarely used in commercial craft. Stuffing boxes are used where the
shaft enters the hull. They very often are mounted in a rubber bellows which
makes them self aligning, but they can be mounted hard to the hull as well.
They are not designed to provide bearing function only that of a water seal.
Very often there will be a grease fitting or oil feed arrangement to keep
them lubed. They too will wear the propeller shaft, so they are not used in
modern commercial craft. The modern replacement device for this function is
a ceramic face, spring loaded water seal, which only require occasional
inspection. The cutlass bearing or equivalent, provides propeller shaft
support at the propeller end. Typically the inboard end of the propeller
shaft is supported by the tail bearing of the marine gearbox. This bearing
also provides propeller thrust support as well by transferring drive force
to the engine mounts. This bearing must be oil lubed and cooled. In some
craft there will be a separate bearing mounted firmly to the hull that
provides the thrust function, but they will be separately oiled and cooled.
If used, it allows the engine to be mounted on vibration absorbing flexible
mounts for sound isolation reasons. I hope this explanation helps.
Steve


"Thomas Wentworth" wrote in message
news:iJStf.2010$WX3.1725@trndny09...

"Steve Lusardi" wrote in message
...
Tom,
I have been watching your other posts as well as this one and it is
pretty clear you are in the beginning stages of consideration for boat
ownership. I'm going to lay out some facts of life you probably won't
want to read, but do need to know.

1) Building a boat is not cheaper than buying one.
2) Owning a boat, using a boat, insuring a boat, establishing a place for
a boat is expensive.
3) Boat maintenance will take most of your free time.
4) If you are married, a boat will be the least popular thing you could
undertake with your other half.
5) The boat hull is 20% of the investment.
6) The majority of boat building attempts fail. The larger the boat, the
greater the failure rate.
7) Number one reason for failure in building is underestimating the total
cost in both money and time.

There are more, but your posts indicate to me that you do not have the
available money, the skills or the tools to either build or own a boat in
the class you are considering. Building a boat is very rewarding and I do
not wish to discourage you, but reality is alive and well. My advise to
you is to build a small day boat first. Get your feet wet. Failure is
affordable and success is just as sweet.
Steve


"Thomas Wentworth" wrote in message
news:huBtf.1992$zJ3.65@trnddc04...
If you know a good site for info about this part of boat ??

Or, can you explain it here.

So far I know ,,,, hole in boat for shaft to go through from engine.
Is the cutlass bearing what lets the shaft turn and not let the water
in?

What and where is the stuffing box?



------------------------------------------

Dear Steve ,,,,,,,,,, oh contraire, my friend. I have actually owned and
sailed three [3] full keel, sailboats.

In fact, one of them was quite famous. But ............... and here is
the BUT part ;;; it was 20 plus years ago.

I think I have forgotten more than I ever knew. As I look into returning
to the high seas, I find that certain aspects of boat owning, maintenace,
repair, operation, cost, etc have either changed dramatically or I can't
remember the method, or procedure to follow. In some cases, such as the
Cutlass Bearing ... I just never had to deal with it as the marina did the
maintenance. That is one difference now; I plan on doing most of my own
work. I have the time ...

I also have two sons who are interested in sailing. At least today they
are.

As for the money ... to be honest, I could go out and purchase a sailboat.
I don't wish to. Why? I want to do it my way. I want things set up for
me. I want a boat that reflects my personal approach to life. I have
been on the fancy piece of fiberglass with all the blocks and sails and
the gear that never gets used. I've sat on boats that never leave the
harbor. I've talked to owners who think of sailing as writing a check.
Ever hear of the New York Yacht Club.

They are to be avoided at all cost. When Wall st goes sailing
................ you don't want to be there.

So,,,, before you make assumptions ..................

Now ............ back to the Cutlass Bearing ...

Let's see ,,, the shaft goes through a shaft log,,, and it is held in
place by a Cutlass Bearing and then there is the stuffing box ....

I'm almost ready for my first "MARINA BILL"..


TALLY HO.

Hello again Thomas,
Let's dispell some more myths...and agree with some truths. We
already know thae all boats do NOT have struts, particularly full-keel
sailboats as opposed to fin-keeled....Many boats of higher -end
construction(Nordhaven comes to mind,for instance) have bearings at the
inner and outer end of the shaft log to reduce load on the TAILSHAFT
bearing of the gearbox or reduction gear and to prevent "whipping of
the shaft" ( a jump-rope-like effect) often caused by a long
unsupported length
of shaft and some misalignment-it doesn't take much-...Most commercial
craft DO have strut and cutlass bearings; I have replaced many more
than I care to count, having been in the marine service industry for
the last 27+ years... The ceramic "face seal" that Steve refers to is a
PSS "dripless shaft seal, and I see them far more often in pleasure
boats than in Commercial applications. More commercial boats who have
oil cooled upper bearings or standard logs use a TIDES type dripless
seal, a lipseal very similar to a grease seal, this must be cooled by
oil (the minority)or raw water which is engine supplied if available or
supplied by a static siphon vent in keel- cooled apps, and typically
with lower shaft RPM's (under 2000) The oil cooled stuffing boxes are
becoming increasingly scarce on all but ships, they are environmentally
detrimental as they leak oil to seawater intentionally, the approved
versions are completely lubricant-captive and are quite expensive.The
stand alone bearing and support Steve speaks of(Aqua-Drive) and similar
has a twofold purpose: it allows major shaft misalignment to facilitate
a variety of engine installations and it transfers thust directly to
the stringers as Steve said...However, the vast-almost all-majority of
propulsion engines are mounted on flexible,vibration dampening mounts,
with or without an intermediate bearing and supports...in virtually all
pleasurecraft and most small to medium commercial apps.
........But this is far more information than I think you were
seeking...lol
Good luck in whatever venture you decide to take on...Screw the
NYYC types....
Best Regards,
markvictor