Does anyone know what to do to oar rubbers to get them onto an oar?
I've got this lovely, very practical full ring stainless rowlocks that
I want to use, but I'm going a bit spare trying to get the oar rubbers
on. I've searched everywhere, does anyone know the secret?

Thanks,
Robin

PS: This is pretty much my final building task on my 16' Ian Oughtred
Ness boat I started in 1996.

Heat them up in hot water.
After they cool, they will be very tight again.


"Robin Hilliard" wrote in message
oups.com...
Does anyone know what to do to oar rubbers to get them onto an oar?
I've got this lovely, very practical full ring stainless rowlocks that
I want to use, but I'm going a bit spare trying to get the oar rubbers
on. I've searched everywhere, does anyone know the secret?

Thanks,
Robin

PS: This is pretty much my final building task on my 16' Ian Oughtred
Ness boat I started in 1996.





----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 100,000 Newsgroups
---= East/West-Coast Server Farms - Total Privacy via Encryption =---

I don't know exactly what you have but I would expect that if you can warm
the rubber in a hot water bath and soap up the oar they may slide on quite
easily.

John

"Robin Hilliard" wrote in message
oups.com...
Does anyone know what to do to oar rubbers to get them onto an oar?
I've got this lovely, very practical full ring stainless rowlocks that
I want to use, but I'm going a bit spare trying to get the oar rubbers
on. I've searched everywhere, does anyone know the secret?

Thanks,
Robin

PS: This is pretty much my final building task on my 16' Ian Oughtred
Ness boat I started in 1996.

Not sure if this will work, but a trick I use to use for putting rubber
handlebar grips onto motorcycles was coat the inside of the grip with Gas, then
slide it on. Gas softened the rubber and when it evaporated left nothing
behind (unlike soap which tended to allow the grips to slide off as well as on
:-)

-al-

"Robin Hilliard" wrote in message
roups.com...
Does anyone know what to do to oar rubbers to get them onto an oar?
I've got this lovely, very practical full ring stainless rowlocks that
I want to use, but I'm going a bit spare trying to get the oar rubbers
on. I've searched everywhere, does anyone know the secret?

Thanks,
Robin

PS: This is pretty much my final building task on my 16' Ian Oughtred
Ness boat I started in 1996.

I agree with the soap and water or use go jo.
Works like a champ putting the foam grips on fishing rods and shold do the
trick for your oars.



---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.788 / Virus Database: 533 - Release Date: 11/1/04

These sound like what I put on some oars about 15 yr ago, and my
recollection is that the directions said to roll them up, like a doughnut
and then roll them on the oar, making sure it is done the right direction.
One would need to work the doughnut in the right spot before unrolling it.

"Robin Hilliard" wrote in message
oups.com...
Does anyone know what to do to oar rubbers to get them onto an oar?
I've got this lovely, very practical full ring stainless rowlocks that
I want to use, but I'm going a bit spare trying to get the oar rubbers
on. I've searched everywhere, does anyone know the secret?

Thanks,
Robin

PS: This is pretty much my final building task on my 16' Ian Oughtred
Ness boat I started in 1996.

Methylated spirits will do the job without the risk of damage that petrol
(gas) or petroleum oils do to rubber, soap stays put for awhile and will let
the rubbers slide up and down.

Hi
A bit off/ topic but if you were asking about plastic tube it will not
be heat that make the profesional solution ------- there are a mix of
acetone and tricloretylene quite common chemicals that make magic . If
you ever tried this fluid you never use anything else when having
trouble with a hose even halve the diameter of what it shuld be .
Acetone alone can do the trick but is a bit to heavy , anyway if you
place a plastic hose in this solution the diameter can grow up 3 times
what it was, then just leave it there where you want to put it then
when the fluid are vapored out the plastic hose is back to the original
size and very tight.

P.C.

I've seen reference to methylated spirits on several occasions recently
and would like to know what it is, where do you get it and what's it
cost, please?

Thank you,
Courtney



Roger & Lorraine Martin wrote:

Methylated spirits will do the job without the risk of damage that petrol
(gas) or petroleum oils do to rubber, soap stays put for awhile and will let
the rubbers slide up and down.





--
s/v Mutiny
Rhodes Bounty II
lying Oriental, NC
WDB5619

Meths is the common name in the UK/Australia for denatured (undrinkable)
wood alcohol. Blue in colour - well it is in Australia, cheaper than a
bottle of Coke. We can buy it from places as diverse as afeways/Woolworths
and the Hardware stores.

Hope you have luck with it.

"Courtney Thomas" wrote in message
...
I've seen reference to methylated spirits on several occasions recently
and would like to know what it is, where do you get it and what's it
cost, please?

Thank you,
Courtney



Roger & Lorraine Martin wrote:

Methylated spirits will do the job without the risk of damage that
petrol
(gas) or petroleum oils do to rubber, soap stays put for awhile and will
let
the rubbers slide up and down.





--
s/v Mutiny
Rhodes Bounty II
lying Oriental, NC
WDB5619