new boat
 

According to the manual, the interface "may be used with any radio
navigation system that uses NMEA the 0180, 0181, or 0183 standard," so it
looks like I should be good to go....

--
"j" ganz @@
www.sailnow.com

"Dave" wrote in message
...
On Tue, 5 Sep 2006 16:51:15 -0700, "Capt. JG"
said:

seems to have the ability to work off the GPS that's also on the boat.

I dunno. The older units used a proprietary protocol called "Sea Talk"
(hence the "ST") and wouldn't understand NMEA (sp???). To interface the
two
required an interface box to convert the Sea Talk back and forth.

new boat
 

Capt. JG wrote:
According to the manual, the interface "may be used with any radio
navigation system that uses NMEA the 0180, 0181, or 0183 standard," so it
looks like I should be good to go....

My previous boat came with the old Nautec Autohelm 5000 auto pilot,
circa 1985. I don't know what inputs it took. I replaced it with a
ST4000 in 1994 and it was certainly NMEA compatible.

new boat
 

Kewl.

--
"j" ganz @@
www.sailnow.com

"Jeff" wrote in message
. ..
Capt. JG wrote:
According to the manual, the interface "may be used with any radio
navigation system that uses NMEA the 0180, 0181, or 0183 standard," so it
looks like I should be good to go....

My previous boat came with the old Nautec Autohelm 5000 auto pilot, circa
1985. I don't know what inputs it took. I replaced it with a ST4000 in
1994 and it was certainly NMEA compatible.

new boat
 

"Capt. JG" wrote in message
...
have juice, fuel, I called
the yard where she
had some engine work done (tune up, oil change, and the
like). Oh, it's not
our fault, maybe you're out of gas (no), maybe you
don't
have her in neutral
(no neutral safety switch on this boat - something to
think about adding).

Don't, they're stupid.

When I called the previous owner to confirm that it didn't
have one, he told
me he started the engine a couple of times in reverse. :-}


yes, but you're too smart to do that.




Come back, and we'll look into it... of course, it's a
good hour or so in
such light winds, and guess what they close in 1/2
hour.

Frustrated, I called the former owner, who couldn't
think
of any reason this
would happen. Never happened to him in 10 years. Must
be a
disconnected
wire, but he's busy at work, and the manual is in my
car
(note for later,
put manual on boat). Called the yard back... they said,
oh, maybe we forgot
to tighten the wire to the starter solenoid.
Unfortunately, I have no idea
where this wire is.


Sailing in the wee hours I noticed my nav lights
dimming,
went to start the engine ( with the starter batt) and
nada.
I also hove to as the battery was too low to trust the
AP.
The selenoid wire had broken , right at the terminal
end. I
stripped it and put it back on bare wire. Got a terminal
3
days later.

I need to replace the lenses.


lenses????

new boat
 

Bifocals. I meant the lenses for the running lights.

--
"j" ganz @@
www.sailnow.com

"Scotty" wrote in message
. ..

"Capt. JG" wrote in message
...
have juice, fuel, I called
the yard where she
had some engine work done (tune up, oil change, and the
like). Oh, it's not
our fault, maybe you're out of gas (no), maybe you
don't
have her in neutral
(no neutral safety switch on this boat - something to
think about adding).

Don't, they're stupid.

When I called the previous owner to confirm that it didn't
have one, he told
me he started the engine a couple of times in reverse. :-}


yes, but you're too smart to do that.




Come back, and we'll look into it... of course, it's a
good hour or so in
such light winds, and guess what they close in 1/2
hour.

Frustrated, I called the former owner, who couldn't
think
of any reason this
would happen. Never happened to him in 10 years. Must
be a
disconnected
wire, but he's busy at work, and the manual is in my
car
(note for later,
put manual on boat). Called the yard back... they said,
oh, maybe we forgot
to tighten the wire to the starter solenoid.
Unfortunately, I have no idea
where this wire is.


Sailing in the wee hours I noticed my nav lights
dimming,
went to start the engine ( with the starter batt) and
nada.
I also hove to as the battery was too low to trust the
AP.
The selenoid wire had broken , right at the terminal
end. I
stripped it and put it back on bare wire. Got a terminal
3
days later.

I need to replace the lenses.


lenses????

new boat
 

True Katy - maidens are never as they appear on the surface!
Scout

"katy" wrote in message
...
Capt. JG wrote:
Here's a synopsis of Excalibur's maiden voyage from the yard in SF to her
new home...

The maiden voyage was interesting... single-handed her from SF South
Beach Harbor to Richmond. Engine started fine at the dock, so I raised
sails and headed up toward the Bay Bridge. Near the bridge, the wind
died, so I go to start the engine... nada... not even cranking, nothing.
After some preliminary checks, like do I have juice, fuel, I called the
yard where she had some engine work done (tune up, oil change, and the
like). Oh, it's not our fault, maybe you're out of gas (no), maybe you
don't have her in neutral (no neutral safety switch on this boat -
something to think about adding). Come back, and we'll look into it... of
course, it's a good hour or so in such light winds, and guess what they
close in 1/2 hour.

Frustrated, I called the former owner, who couldn't think of any reason
this would happen. Never happened to him in 10 years. Must be a
disconnected wire, but he's busy at work, and the manual is in my car
(note for later, put manual on boat). Called the yard back... they said,
oh, maybe we forgot to tighten the wire to the starter solenoid.
Unfortunately, I have no idea where this wire is. Fortunately, not much
vessel traffic where I'm floating, so I heave-to to a starboard tack
(give myself at least some status), open up the engine compartment, and I
go upside down inside the engine, one hand on a cell phone dying battery,
flashlight in my mouth, trying to listen/talk to the yard so their
"mechanic" can direct me, the other hand trying to reach the stupid wire.
Finally, found it, tightened it, and then she started no problem. Oh
yeah, and they didn't reconnect the low-oil and temp alarms either.

Got past the bridge, the wind picked up, so killed the engine and started
sailing again. Got about 20 kts steady wind the rest of the way, mostly
port tack. Finally had to jibe to avoid a tug/barge coming out of the
Richmond area, and the rest was easy, even did a passable job flaking the
main before I got to the dock.

Did you really think that a maiden voyage was going to be uneventful? How
naive, Jon. G;ad you made it to harbor safely.

new boat
 

Scout wrote:
True Katy - maidens are never as they appear on the surface!
Scout

"katy" wrote in message
...
Capt. JG wrote:
Here's a synopsis of Excalibur's maiden voyage from the yard in SF to her
new home...

The maiden voyage was interesting... single-handed her from SF South
Beach Harbor to Richmond. Engine started fine at the dock, so I raised
sails and headed up toward the Bay Bridge. Near the bridge, the wind
died, so I go to start the engine... nada... not even cranking, nothing.
After some preliminary checks, like do I have juice, fuel, I called the
yard where she had some engine work done (tune up, oil change, and the
like). Oh, it's not our fault, maybe you're out of gas (no), maybe you
don't have her in neutral (no neutral safety switch on this boat -
something to think about adding). Come back, and we'll look into it... of
course, it's a good hour or so in such light winds, and guess what they
close in 1/2 hour.

Frustrated, I called the former owner, who couldn't think of any reason
this would happen. Never happened to him in 10 years. Must be a
disconnected wire, but he's busy at work, and the manual is in my car
(note for later, put manual on boat). Called the yard back... they said,
oh, maybe we forgot to tighten the wire to the starter solenoid.
Unfortunately, I have no idea where this wire is. Fortunately, not much
vessel traffic where I'm floating, so I heave-to to a starboard tack
(give myself at least some status), open up the engine compartment, and I
go upside down inside the engine, one hand on a cell phone dying battery,
flashlight in my mouth, trying to listen/talk to the yard so their
"mechanic" can direct me, the other hand trying to reach the stupid wire.
Finally, found it, tightened it, and then she started no problem. Oh
yeah, and they didn't reconnect the low-oil and temp alarms either.

Got past the bridge, the wind picked up, so killed the engine and started
sailing again. Got about 20 kts steady wind the rest of the way, mostly
port tack. Finally had to jibe to avoid a tug/barge coming out of the
Richmond area, and the rest was easy, even did a passable job flaking the
main before I got to the dock.

Did you really think that a maiden voyage was going to be uneventful? How
naive, Jon. G;ad you made it to harbor safely.


I suppose you have vast experience delving into the matter.....

new boat
 

Capt. JG wrote:
...... upside down inside the engine, one hand
on a cell phone dying battery, flashlight in my mouth, trying to listen/talk
to the yard so their "mechanic" can direct me, the other hand trying to
reach the stupid wire.

Well, look at it philosophically... every small piece of
knowledge is good... it won't be the last time you hang
upside down hugging the engine... hopefully you will learn
all details of the boat's wiring and can correct other
little problems before they so rudely interrupt the fun.


..... Oh yeah, and they didn't reconnect the low-oil and temp alarms
either.


See what I mean?
Actually disconnected alarms are the best, they never go off
and cause problems & worry.

Fresh Breezes- Doug King

new boat
 

Congratulations. Look's like a nice boat. You've come a long way in ten
years.

--
jlrogers±³©
"Capt. JG" wrote in message
...
Here's a synopsis of Excalibur's maiden voyage from the yard in SF to her
new home...

The maiden voyage was interesting... single-handed her from SF South Beach
Harbor to Richmond. Engine started fine at the dock, so I raised sails and
headed up toward the Bay Bridge. Near the bridge, the wind died, so I go
to start the engine... nada... not even cranking, nothing. After some
preliminary checks, like do I have juice, fuel, I called the yard where
she had some engine work done (tune up, oil change, and the like). Oh,
it's not our fault, maybe you're out of gas (no), maybe you don't have her
in neutral (no neutral safety switch on this boat - something to think
about adding). Come back, and we'll look into it... of course, it's a good
hour or so in such light winds, and guess what they close in 1/2 hour.

Frustrated, I called the former owner, who couldn't think of any reason
this would happen. Never happened to him in 10 years. Must be a
disconnected wire, but he's busy at work, and the manual is in my car
(note for later, put manual on boat). Called the yard back... they said,
oh, maybe we forgot to tighten the wire to the starter solenoid.
Unfortunately, I have no idea where this wire is. Fortunately, not much
vessel traffic where I'm floating, so I heave-to to a starboard tack (give
myself at least some status), open up the engine compartment, and I go
upside down inside the engine, one hand on a cell phone dying battery,
flashlight in my mouth, trying to listen/talk to the yard so their
"mechanic" can direct me, the other hand trying to reach the stupid wire.
Finally, found it, tightened it, and then she started no problem. Oh yeah,
and they didn't reconnect the low-oil and temp alarms either.

Got past the bridge, the wind picked up, so killed the engine and started
sailing again. Got about 20 kts steady wind the rest of the way, mostly
port tack. Finally had to jibe to avoid a tug/barge coming out of the
Richmond area, and the rest was easy, even did a passable job flaking the
main before I got to the dock.

--
"j" ganz @@
www.sailnow.com

"Capt. JG" wrote in message
...
I finally concluded the purchase of a new, used boat. She's a Sabre 30,
Mark II, built in 1983. Except for a few minor problems, she's in great
shape. I'll probably be putting a furler on in the next couple of weeks,
but there's no huge rush as the current setup is pretty easy.

Here are a couple of picture links... on the hard and then me
single-handing to her new home in Richmond, CA.

http://sailnow.photosite.com/excalibur/
http://sailnow.photosite.com/Excalibur_maiden_voyage/

The cockpit is nice... 7'2" :-)

--
"j" ganz @@
www.sailnow.com

new boat
 

Capt. JG wrote:
Bifocals. I meant the lenses for the running lights.

Me too! Do you have Aqua Signal light?

Let me know where you find lenses.

Joe

--
"j" ganz @@
www.sailnow.com

"Scotty" wrote in message
. ..

"Capt. JG" wrote in message
...
have juice, fuel, I called
the yard where she
had some engine work done (tune up, oil change, and the
like). Oh, it's not
our fault, maybe you're out of gas (no), maybe you
don't
have her in neutral
(no neutral safety switch on this boat - something to
think about adding).

Don't, they're stupid.

When I called the previous owner to confirm that it didn't
have one, he told
me he started the engine a couple of times in reverse. :-}


yes, but you're too smart to do that.




Come back, and we'll look into it... of course, it's a
good hour or so in
such light winds, and guess what they close in 1/2
hour.

Frustrated, I called the former owner, who couldn't
think
of any reason this
would happen. Never happened to him in 10 years. Must
be a
disconnected
wire, but he's busy at work, and the manual is in my
car
(note for later,
put manual on boat). Called the yard back... they said,
oh, maybe we forgot
to tighten the wire to the starter solenoid.
Unfortunately, I have no idea
where this wire is.


Sailing in the wee hours I noticed my nav lights
dimming,
went to start the engine ( with the starter batt) and
nada.
I also hove to as the battery was too low to trust the
AP.
The selenoid wire had broken , right at the terminal
end. I
stripped it and put it back on bare wire. Got a terminal
3
days later.

I need to replace the lenses.


lenses????